Engineering topics

Harrah, S. D.

Publications and source records attributed to Harrah, S. D..

5 records

NASA NTRS1995

Simulation of the 1994 Charlotte Microburst with Look-Ahead Windshear Radar

A severe microburst occurred on 2 July 1994 at Charlotte, NC, and was associated with the crash of USAir Flight 1016 (FL-1016) (Salottolo 1994; Phillips 1994). The inbound DC-9 unexpectedly encountered a rapidly intensifying rainshaft just seconds before it was to touchdown on runway 18R. The aircraft crashed after encountering strong windshear, killing 37 of the 57 souls on board. The pilots did not recognize the windshear condition in time to prevent the accident and received no warning from the aircraft's Honeywell in-situ windshear detection system or from ground-based systems (Charlotte maintains both an ASR-9 weather radar and a Phase-2 LLWAS). Also two other aircraft landed ahead of FL-1016 without incident and reported smooth approaches to 18R. Section-2 of this paper reports briefly on the reconstruction of the event based on numerical results generated by the Terminal Area Simulation System (TASS) as presented at the National Transportation Safety Board (NTSB) public hearing (Proctor 1994). Section-3 discusses the simulation of this event with a look-ahead windshear radar.

Proctor, F. H.↗

NASA NTRS1993

Integrated display of multi-sensor geophysical and electromagnetic flight data

Low-altitude wind shear has been identified by several aviation interests as a significant hazard to the safety of flying. The hazard may be greatest when the wind shear is due to an unpredicted and short-lived microburst occurring in the immediate flight path of an aircraft during takeoff or landing. Researchers from the NASA Langley Research Center have investigated wind shear by developing a suite of remote sensing instruments and then using these instruments in an airborne wind shear detection flight program. Among these instruments were a Doppler radar, a lidar, and an infrared sensor; these were supported by in situ measurements of aircraft and environmental parameters and by ground-based Doppler radars. The basic problem addressed was the airborne detection and measurement of meteorologically-induced wind shear sufficiently ahead of the aircraft to allow avoidance. If the remote measurements of the shear and its associated radar reflectivity did not exceed set limits, the airplane then continued through the wind shear so that in situ measurements could be made for comparison. Initial detection and vectoring to the wind shear was normally given from a ground-based Doppler weather radar and most of the wind shear events were due to microbursts, both wet and dry. This paper considers the problems of sampling the wind shear event, time and space registration among the various sensors, coordination of the various sensors' beams and sampling volumes, and also various techniques for portraying the data, both for research and for presentation. Examples are given based on data from the 1991 and 1992 NASA/FAA wind shear flights, and the results and conclusions are generalized to other flight experiments involving multi-sensor electromagnetic data sets.

Delnore, V. E.↗

NASA NTRS1993

Description and availability of airborne Doppler radar data

An airborne, forward-looking, pulse, Doppler radar has been developed in conjunction with the joint FAA/NASA Wind Shear Program. This radar represents a first in an emerging technology. The radar was developed to assess the applicability of an airborne radar to detect low altitude hazardous wind shears for civil aviation applications. Such a radar must be capable of looking down into the ground clutter environment and extracting wind estimates from relatively low reflectivity weather targets. These weather targets often have reflectivities several orders of magnitude lower than the surrounding ground clutter. The NASA radar design incorporates numerous technological and engineering achievements in order to accomplish this task. The basic R/T unit evolved from a standard Collins 708 weather radar, which supports specific pulse widths of 1-7 microns and Pulse Repetition Frequencies (PRF) of less than 1-10 kHz. It was modified to allow for the output of the first IF signal, which fed a NASA developed receiver/detector subsystem. The NASA receiver incorporated a distributed, high-speed digital attenuator, producing a range bin to range bin automatic gain control system with 65 dB of dynamic range. Using group speed information supplied by the aircraft's navigation system, the radar signal is frequency demodulated back to base band (zero Doppler relative to stationary ground). The In-phase & Quadrature-phase (I/Q) components of the measured voltage signal are then digitized by a 12-bit A-D converter (producing an additional 36 dB of dynamic range). The raw I/Q signal for each range bin is then recorded (along with the current radar & aircraft state parameters) by a high-speed Kodak tape recorder.

Harrah, S. D.↗

NASA NTRS1991

Transverse electric scattering widths for strips-Fourier transform technique

A technique which is based on Fourier transformations is introduced for predicting scattering widths. For a strip it is shown that explicit determination of the linear current density is not necessary for bistatic or monostatic scattering width calculations. Comparisons of the predictions of the technique are made with the integral equation technique predictions, which do not require explicit evaluations of linear current densities.

Cockrell, C. R.↗

NASA NTRS1990

An analysis of the effects of secondary reflections on dual-frequency reflectometers

The error-producing mechanism involving secondary reflections in a dual-frequency, distance measuring reflectometer is examined analytically. Equations defining the phase, and hence distance, error are derived. The error-reducing potential of frequency-sweeping is demonstrated. It is shown that a single spurious return can be completely nullified by optimizing the sweep width.

Hearn, C. P.↗