Engineering topics

Harrison, Shay

Publications and source records attributed to Harrison, Shay.

4 records

DOE OSTI2024

Emerging continuous SiC fibers for high-temperature applications

Silicon carbide (SiC) fibers are responsible for the ultimate strength and toughness of SiC-fiber reinforced composites in harsh environments. The development of a new generation of continuous SiC fibers continues to advance the mechanical properties of composite materials. Tyranno™ SA4 fiber was recently released as a successor of Tyranno™ SA3 fiber. Laser-driven chemical vapor deposition (LCVD) has been adopted as an alternative fiber processing route to synthesizing high-strength SiC fiber with tailorable small diameters and chemical compositions. Both Tyranno™ SA4 and laser-driven CVD fibers show very high tensile strength, about 4 GPa in the as-fabricated condition. The degradation of thermal stability and strength due to annealing in an inert environment were similar for Tyranno™ SA3 and SA4 fibers because of their similar carbon-rich, crystalline microstructure. Silicon-rich fibers produced by LCVD possessed heterogeneous crystallinity, which was attributed to laser power distribution and showed microstructural instability at 1500 °C and above. Finally, the new SiC fibers demonstrated an increase in as-fabricated strength but faced the same challenges in environmental resistance as the traditional SiC fibers do.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Hydrothermal corrosion of laser printed SiC fibers under extreme environment

We report SiC/SiC fiber composites are proposed cladding materials to improve the accident tolerance of commercial light water nuclear reactor fuel. To evaluate their viability, understanding the kinetics of corrosion under irradiation and high-temperature, high-pressure aqueous environment is critical. In the present work, the microstructure and mechanical properties of novel SiC fibers manufactured by Laser Chemical Vapor Deposition (LCVD) are introduced. The LCVD technology has control over microstructure and stoichiometry while allowing for high purity manufacturing, all key qualities needed in search of an optimum SiC fiber for nuclear energy applications. The isolated hydrothermal corrosion of commercially available carbon-rich Hi-Nicalon Type-S fibers is compared to the LCVD stoichiometric and LCVD silicon-rich fibers. Autoclave testing was carried out at 310°C and 14 MPa in the absence of irradiation. In a separate study, the effect of gamma irradiation on the fibers in the room-temperature environment was analyzed. It was observed from the experiments that the dissolution of the fibers was highly dependent on the stoichiometric ratio, fiber surface morphology and thermal pre-treatment of fibers. Contrary to previous findings, fiber dissolution was also visible under low-temperature gamma irradiation in aqueous environment with LCVD fibers showing lower dissolution.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Additive manufacturing of silicon carbide for nuclear applications

Additive manufacturing (AM) is a rapidly evolving technology being considered for nuclear applications. A special focus on AM to fabricate nuclear-grade silicon carbide (SiC) is explored in this paper. First, we present currently available AM processing options for SiC. AM methods commonly used for other ceramics, in which the feedstocks are forms of polymers, powders, and/or reactive chemical vapors, are also applicable to SiC. SiC phases are formed by pyrolysis of pre-ceramic polymer, direct reaction of powder precursors, sintering of SiC powders, or chemical vapor deposition/infiltration. Second, we discuss how the different microstructures of SiC materials fabricated by various processing methods affect their behavior in nuclear environments. Third, we discuss state-of-the-art AM technologies for the fabrication of relatively pure SiC, which show great potential to retain its strength under neutron irradiation: (1) binder jet printing followed by chemical vapor infiltration, (2) laser chemical vapor deposition, and (3) selective laser sintering of SiC powders.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Innovative accident tolerant fuel concept enabled through direct manufacturing technology

Nuclear energy is one of the largest sources of carbon-free electricity in the world. Some countries are looking at new ways to support and revitalize the nuclear sector since the Fukushima disaster. The accident tolerant fuel program is geared toward improving the safety of nuclear energy by investigating materials that can replace or modify the current uranium-dioxide nuclear fuel and zirconium-based cladding. This research program is being supported by all major nuclear countries since 2011. The practical limitations on allowable uranium enrichment has taken the focus away from the most promising fuels with high radioactivity retention such as tristructural isotropic particle fuel. To overcome such enrichment limitation, a new fuel concept is proposed using advanced ceramic direct manufacturing with laser-induced chemical vapor deposition. The fuel-as-fiber concept is an accident-tolerant fuel design that features high thermal conductivity, strong capability of radioactivity retention and most importantly requires reasonable enrichment levels with uranium nitride as the fuel. In this work, the initial fabrication of uranium-based fuel with laser-induced chemical vapor deposition technology is demonstrated. Then an advanced multi-physics guided modeling approach based on finite element analysis codes and informed by the manufacturing capabilities is developed to accelerate the advancement of fuel-as-fiber concept for use in current light-water reactor technology. The detailed thermomechanical analysis showed promising results for viability of the innovative fuel-as-fiber concept. The predicted stresses in the fuel structural materials were similar to the case of tristructural isotropic particle fuel experience base that has shown excellent reliability in retention of fuel radioactivity at high temperatures.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗