Search NASA⌕ Search

Engineering topics

Hassanein, A.

Publications and source records attributed to Hassanein, A..

At least 19 records

Comprehensive analysis of disruption mitigation methods using gas and pellet-like injections in ITER-like Tokamaks

Abstract Inert-gas shielding could be an effective mechanism for protection of plasma facing surfaces (PFS) against plasma particles impact and photon radiation heat loads during transient events in fusion devices. Neutral gas injection is one promising way to mitigate erosion of tokamak components and contamination. The objective of this work is to study and optimize mitigation methods using neutral gas and pellet-like injections to decrease the heat load to the divertor surfaces and to prevent vaporization of the various internal surfaces due to transient events in ITER-like devices. The integrated self-consistent models implemented in the HEIGHTS package was used for detailed analysis of the potential secondary plasma generation from the injected inert gas, its radiative characteristics, and shielding effectiveness. We varied the density, size, and location of an argon gas cloud to minimize the disruption energy deposited into the divertor components. We also investigated innovative ways for minor changes in ITER-like internal design to mitigate disruptions. We found the optimum parameters to fully protect ITER tokamak surfaces from erosion and vaporization during plasma instabilities. This preliminary analysis showed that using Ar gas injection methods could lead to enhancement in components lifetime in ITER-like and future DEMO devices with minor design changes.

Science & Technology - Other Topics↗

Temporal pre-pulse shaping in dual pulse laser produced plasma for the optimization of the EUV source in tin microdroplet system

Dual-laser beams interacting with small droplets of liquid tin are currently the most efficient systems for producing the 13.5 nm EUV photon radiation source required for the next generation microchips. Usually, EUV light is produced during the second main-pulse stage, while the pre-pulse (PP) is used for target preparation, i.e., droplet preheating, vaporization, and target deformation. However, the PP laser energy can be utilized more efficiently if the EUV producing plasma is being developed during the PP stage as well. In this work, we study the ways of optimization of the PP laser temporal shape to achieve conditions for maximum EUV output during the pre-pulse. The size of the deformed droplet is kept optimized for the following main laser pulse. Our simulations showed a significant increase in the EUV output at the pre-pulse stage when a ramping profile is used for the laser temporal shape. Using the ramped square pre-pulse produces 24% gain in the EUV output in comparison with the standard Gaussian temporal profile (i.e., regular Nd:YAG shape) for the same energy of the laser pulse.

36 MATERIALS SCIENCE↗

ELM sputter erosion modeling of a tungsten coated small angle slot divertor in DIII-D

We modeled plasma edge localized mode (ELM) sputter erosion for a Small Angle Slot divertor with a tungsten coated region (SAS-VW), designed for experiments in the DIII-D tokamak, and proposed for use in future advanced tokamaks. The simulations use a free-streaming, 1000 eV, C +6 and D +1 ELM impingement model, with SOLPS-ITER, ITMC-DYN, and REDEP/WBC code packages for background plasma, material response, and erosion/redeposition respectively. The results show ELM'ing plasma gross and net tungsten erosion fluxes of the mixed-material C/W surface peaking at the slot entrance region, and an order of magnitude higher than for non-ELMs. The per-pulse erosion, however, remains low, of order 0.5 nm, due to expected moderate ELM frequencies and duration in DIII-D. Here, the ELMs result in a ~25x higher peak sputtered W current leaving the divertor slot region, towards the core plasma, compared to the ELM-free plasma case. The time-integrated escape current, however, may not significantly affect core plasma high-Z contamination concerns, for a 1% ELM duty factor, but may be an issue for higher frequency ELMs. In general, the modeling results appear favorable for effective testing of the SAS-VW divertor in DIII-D, and extrapolation to innovative divertor designs in future ITER-like and DEMO fusion devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Liquid lithium as divertor material to mitigate severe damage of nearby components during plasma transients

The successful operation of thermonuclear fusion reactors such as ITER, DEMO, and future commercial plants is mainly determined by the optimum choice of materials for various components. The objective of this work is to accurately and comprehensively simulate the entire device in 3D to predict pros and cons of various materials, e.g., liquid lithium in comparison to tungsten and carbon to predict future ITER-like and DEMO divertor performances. We used our comprehensive HEIGHTS simulation package to investigate ITER-like components response during transient events in exact 3D geometry. Starting from the lost hot core plasma particles through SOL, deposition on the divertor surface, and the generation of secondary plasma of divertor materials. Our simulations predicted significant reduction in the heat loading and damage to the divertor nearby and internal components in the case when lithium is used on the divertor plates. While if tungsten or carbon are used on the divertor plate, significant melting areas and vaporization spots can occur (less for carbon) on the reflector, dome, and stainless steel tubes, and even parts of the first walls can melt due to the high radiation power of the secondary divertor plasma. Lithium photon radiation deposition into the divertor and nearby surfaces was decreased by two orders of magnitude compared to tungsten and by one order of magnitude compared to carbon. This analysis showed that using liquid lithium for ITER-like surfaces and future DEMO can lead to significant enhancement in components lifetime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

New proposed ITER divertor design using carbon insert on tungsten to mitigate ELMs and secondary radiation effects on nearby components

Abstract Building a successful device for the magnetic fusion energy production is a great challenge. ITER is an international project of the tokamak based magnetic fusion design being developed for the demonstration of the feasibility of thermonuclear technologies for future realization of successful commercial fusion energy. A key obstacle to a successful magnetic fusion energy production is however, the performance during abnormal events including plasma disruptions and edge-localized modes (ELMs). A credible reactor design must tolerate at least a few of these transient events without serious consequences such as melting of the structure. This paper investigates and compares the performance of the current ITER tokamak design during two types of transient events, i.e., ELMs occurring at normal operation and disruptions during abnormal operation. We simulated the divertor components response using our integrated 3D HEIGHTS package. The simulations include self-consistent modeling of the interaction of the released core plasma particles with the initial solid divertor material, energy deposition processes, vaporization of divertor material, secondary plasma formation and MHD evolution, incident core particles collisions and scattering from this dense secondary plasma, photon radiation of secondary plasma, and the resulting heat loads on nearby components. Our simulations showed that using a small carbon insert around the strike point can significantly reduce the overall expected damage on the tungsten dome structure, reflector plates, and prevent tungsten vaporization and its potential core plasma contamination.

47 OTHER INSTRUMENTATION↗

Tungsten–carbon surface evolution and erosion modeling for a small angle slot divertor in DIII-D

Abstract We modeled tungsten–carbon mixed surface evolution, sputtering erosion, and transport for the tungsten coated region of a small angle slot (SAS) divertor design for the DIII-D tokamak. This divertor concept aims to achieve a closed slot dissipative plasma to minimize heat load and surface erosion, and to study high- Z material performance. Our advanced simulations use coupled ITMC-DYN material mixing/response and 3D full kinetic REDEP/WBC erosion/redeposition code packages, with divertor plasma solution from the SOLPS-ITER package with 4 MW power input. The SAS design geometry and resulting in-slot plasma parameters cause significant differences in predicted sputter/transport from a conventional divertor. For 2% C/D incident plasma ratio, an equilibrium mixed C/W surface is attained at ∼30 s of discharge, from wall sputtered carbon transported to the 10 cm long tungsten divertor region. Tungsten remains exposed to the plasma, but the evolved surface composition varies with different C/D ratios. Tungsten is primarily sputtered from the mixed surface by impinging carbon ions in the +1 to +4 charge states, with some self-sputtering. Redeposition of sputtered tungsten to the divertor is significant, ∼80% along the higher plasma temperature attached plasma SAS entrance region, but this is less than the typically near-unity values for a conventional divertor. Plasma-incident carbon is highly backscattered (∼50%) from the mixed surface, with little redeposition (<10%); this helps maintain tungsten in the surface sputter zone. Carbon is mainly sputtered from the mixed surface by D + ions, also with low redeposition (∼10%–30%). Finally, the modeling shows non-zero but low sputtered tungsten current from the divertor to the core plasma direction. These results appear favorable for effective testing of a tungsten-containing SAS divertor in DIII-D, and extrapolation of mixed-material evolution/response findings to the analogous low- Z /high- Z , Be/W, ITER plasma facing system.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

An integrated approach to understanding RF vacuum arcs

Although used in the design and costing of large projects such as linear colliders and fusion tokamaks, the theory of vacuum arcs and gradient limits is not well understood. Almost 120 years after the isolation of vacuum arcs, the exact mechanisms of the arcs and the damage they produce are still being debated. We describe our simple and general model of the vacuum arc that can incorporate all active mechanisms and aims to explain all relevant data. Our four stage model, is based on experiments done at 805 MHz with a variety of cavity geometries, magnetic fields, and experimental techniques as well as data from Atom Probe Tomography and failure analysis of microelectronics. The model considers the trigger, plasma formation, plasma evolution and surface damage phases of the RF arc. This paper also examines how known mechanisms can explain the observed sharp field dependence, fast breakdown times and observed surface damage. We update the model and discuss new features while also pointing out where new data would be useful in extending the model to a wider range of frequencies.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Potential design problems for ITER fusion device

The international thermonuclear experimental reactor (ITER) is a worldwide project currently being built in France for the demonstration of the feasibility of thermonuclear technologies for future realization of successful commercial fusion energy. ITER is of the tokamak based design using strong magnetic fields to confine the very hot plasma needed to induce the fusion reaction. Tokamak devices are currently the front leading designs. Building a successful magnetic fusion device for energy production is of great challenge. A key obstacle to such design is the performance during abnormal events including plasma disruptions and so-called edge-localized modes (ELMs). In these events, a massive and sudden release of energy occurs quickly, due to loss of full or partial plasma confinement, leading to very high transient power loads on the reactor surface boundaries. A successful reactor design should tolerate several of these transient events without serious damages such as melting and vaporization of the structure. This paper highlights, through comprehensive state-of-the-art computer simulation of the entire ITER interior design during such transient events, e.g., ELMs occurring at normal operation and disruptions during abnormal operation, potential serious problems with current plasma facing components (PFCs) design. The HEIGHTS computer package is used in these simulations. The ITER reactor design was simulated in full and exact 3D geometry including all known relevant physical processes involved during these transient events. The current ITER divertor design may not work properly and may requires significant modifications or new innovative design to prevent serious damage and to ensure successful operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Modeling, analysis, and code/data validation of DIII-D tokamak divertor experiments on ELM and non-ELM plasma tungsten sputtering erosion

Abstract We analyzed recent DIII-D tokamak tungsten divertor probe experiments using advanced, coupled, sputter erosion/redeposition, plasma, and surface response code packages. Modeling is done for ELMing H-mode, and L-mode plasmas, impinging on various size tungsten deposits on Divertor Material Evaluation System (DiMES) carbon probes. The simulations compute 3D, full kinetic, sub-gyromotion, impurity sputtering and transport, including changes in tungsten surface composition and response due to mixed deuterium and carbon ions irradiation. Per our analysis, ELM (edge localized mode) plasma sputtering in DIII-D mostly involves free-streaming high energy (∼500–1000 eV) D + and C +6 ions, with high near-surface plasma density. L-Mode sputtering is due to impurity sputtering (C, W) only, with lower density. All cases show complete redeposition of tungsten on the divertor, with significant redeposition on the tungsten spots themselves, and low self-sputtering. Comparison of ELM plasma gross tungsten erosion simulation results with in-situ spectroscopic data is good, as are code/data comparisons of net erosion using post-exposure Rutherford backscattering (RBS) data for the L-mode probes. The analysis, extrapolated to a full tungsten divertor, implies low net erosion and negligible plasma contamination from sputtering. These results support the use of high-Z plasma facing surfaces in ITER and beyond.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fusion Energy Sciences Exascale Requirements Review. An Office of Science review sponsored jointly by Advanced Scientific Computing Research and Fusion Energy Sciences, January 27-29, 2016, Gaithersburg, Maryland

The additional computing power offered by the planned exascale facilities could be transformational across the spectrum of plasma and fusion research — provided that the new architectures can be efficiently applied to our problem space. The collaboration that will be required to succeed should be viewed as an opportunity to identify and exploit cross-disciplinary synergies. To assess the opportunities and requirements as part of the development of an overall strategy for computing in the exascale era, the Exascale Requirements Review meeting of the Fusion Energy Sciences (FES) community was convened January 27–29, 2016, with participation from a broad range of fusion and plasma scientists, specialists in applied mathematics and computer science, and representatives from the U.S. Department of Energy (DOE) and its major computing facilities. This report is a summary of that meeting and the preparatory activities for it and includes a wealth of detail to support the findings. Technical opportunities, requirements, and challenges are detailed in this report (and in the recent report on the Workshop on Integrated Simulation). Science applications are described, along with mathematical and computational enabling technologies. Also see http://exascaleage.org/fes/ for more information.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A Comparative Study of Single-pulse and Double-pulse Laser-Induced Breakdown Spectroscopy with Uranium-containing Samples

Laser-induced breakdown spectroscopy (LIBS) holds potential advantages in special nuclear material (SNM) sensing and nuclear forensics which require rapid analysis, minimal sample preparation and stand-off distance capability. SNM, such as U, however, result in crowded emission spectra with LIBS, and characteristic emission lines are challenging to discern. It is well-known that double-pulse LIBS (DPLIBS) improves the signal intensity for analytes over conventional single-pulse LIBS (SPLIBS). This study investigates U signal in a glass matrix using DPLIBS and compares to signal features obtained using SPLIBS. DPLIBS involves sequential firing of 1.06 µm Nd:YAG pre-pulse and 10.6 µm TEA CO2 heating pulse in near collinear geometry. Optimization of experimental parameters including inter-pulse delay and energy follows identification of characteristic lines and signals for bulk analyte Ca and minor constituent analyte U for both DPLIBS and SPLIBS. Spatial and temporal coupling of the two pulses in the proposed DPLIBS technique yields improvements in analytical merits with negligible further damage to the sample compared to SPLIBS. Subsequently, the study discusses optimum plasma emission conditions of U lines and relative figures of merit in both SPLIBS and DPLIBS. Investigation into plasma characteristics also addresses plausible mechanisms related to observed U analyte signal variation between SPLIBS and DPLIBS.

Skrodzki, P. J.↗

Characterization of ultrafast laser-ablation plasma plumes at various Ar ambient pressures

Expansion dynamics and internal plume structures of fs laser ablated brass plasma in Ar at various pressure levels ranging from vacuum to atmospheric were studied using multitude of diagnostic tools including time resolved and time integrated 2-dimensional imaging, optical time of flight measurements and visible emission spectroscopy. Temporal evolution of excited Cu and Zn species in the plume were imaged using band pass interference filters and compared its hydrodynamic expansion features with spectrally integrated images of the plume. 2D imaging coupled with monochromatic line selection showed several interesting features at various pressure levels which include velocity differences among the plume species, emission intensity distribution, plasma temperature, electron density etc. Plume confinement, enhanced signal intensity, and dual peak structures in time-of-flight profiles were observed at intermediate pressure range of ~10 Torr. Optimum signal to background ratio was also observed in this pressure range. As a result, possible mechanisms for observed changes in plume shape, optical emission intensity and dual peak structures in time-of-flight profiles were discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Collimation of laser-produced plasmas using axial magnetic field

We investigated the expansion dynamics of laser-produced plasmas expanding into an axial magnetic field. Plasmas were generated by focusing 1.064 µm Nd:YAG laser pulses onto a planar tin target in vacuum and allowed to expand into a 0.5 T magnetic-filed where field lines were aligned along the plume expansion direction. Gated images employing intensified CCD showed focusing of the plasma plume, which were also compared with results obtained using particle-in-cell modelling methods. The estimated density and temperature of the plasma plumes employing emission spectroscopy revealed significant changes in the presence and absence of the 0.5T magnetic field. In the presence of the field, the electron temperature is increased with distance from the target, while the density showed opposite effects.

laser produced plasma↗

An overview of recent physics results from NSTX

Currently, the National Spherical Torus Experiment (NSTX) is being upgraded to operate at twice the toroidal field and plasma current (up to 1 T and 2 MA), with a second, more tangentially aimed neutral beam (NB) for current and rotation control, allowing for pulse lengths up to 5 s. Recent NSTX physics analyses have addressed topics that will allow NSTX-Upgrade to achieve the research goals critical to a Fusion Nuclear Science Facility. These include producing stable, 100% non-inductive operation in high-performance plasmas, assessing plasma-material interface (PMI) solutions to handle the high heat loads expected in the next-step devices and exploring the unique spherical torus (ST) parameter regimes to advance predictive capability. Non-inductive operation and current profile control in NSTX-U will be facilitated by co-axial helicity injection (CHI) as well as radio frequency (RF) and NB heating. CHI studies using NIMROD indicate that the reconnection process is consistent with the 2D Sweet-Parker theory. Full-wave AORSA simulations show that RF power losses in the scrape-off layer (SOL) increase significantly for both NSTX and NSTX-U when the launched waves propagate in the SOL. Moreover, Toroidal Alfven eigenmode avalanches and higher frequency Alfven eigenmodes can affect NB-driven current through energy loss and redistribution of fast ions. The inclusion of rotation and kinetic resonances, which depend on collisionality, is necessary for predicting experimental stability thresholds of fast growing ideal wall and resistive wall modes. Neutral beams and neoclassical toroidal viscosity generated from applied 3D fields can be used as actuators to produce rotation profiles optimized for global stability. DEGAS-2 has been used to study the dependence of gas penetration on SOL temperatures and densities for the MGI system being implemented on the Upgrade for disruption mitigation. PMI studies have focused on the effect of ELMs and 3D fields on plasma detachment and heat flux handling. Simulations indicate that snowflake and impurity seeded radiative divertors are candidates for heat flux mitigation in NSTX-U. Studies of lithium evaporation on graphite surfaces indicate that lithium increases oxygen surface concentrations on graphite, and deuterium-oxygen affinity, which increases deuterium pumping and reduces recycling. In situ and test-stand experiments of lithiated graphite and molybdenum indicate temperature-enhanced sputtering, although that test-stand studies also show the potential for heat flux reduction through lithium vapour shielding. Non-linear gyro kinetic simulations have indicated that ion transport can be enhanced by a shear-flow instability, and that non-local effects are necessary to explain the observed rapid changes in plasma turbulence. Predictive simulations have shown agreement between a microtearing-based reduced transport model and the measured electron temperatures in a microtearing unstable regime. Finally, two Alfven eigenmode-driven fast ion transport models have been developed and successfully benchmarked against NSTX data. Upgrade construction is moving on schedule with initial physics research operation of NSTX-U planned for mid-2015.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

In-situ TEM/heavy ion irradiation on ultrafine-and nanocrystalline-grained tungsten: Effect of 3 MeV Si, Cu and W ions

Plasma facing components for future fusion applications will experience helium- and neutron-induced structural damage. Direct observation of the in-situ dynamic response of such components during particle beam exposure assists in fundamental understanding of the physical phenomena that give rise to their irradiation resistance. We investigated the response of ultrafine and nanocrystalline-grained tungsten to 3 MeV heavy ion irradiations (Si{sup 2} {sup +}, Cu{sup 3} {sup +} and W{sup 4} {sup +}) for the simulation of neutron-induced damage through transmutation reactions via in-situ ion irradiation–transmission electron microscopy experiments. Defect densities as a function of irradiation dose (displacement per atom) and fluence were studied. Four stages of defect densities evolution were observed, as a function of irradiation dose: 1) increase in defect density at lower doses, 2) higher defect production rate at the intermediate doses (before saturation), 3) reaching the maximum value, and 4) drop of the defect density in the case of W{sup 4} {sup +}, possibly due to defect coalescence and grain boundary absorption of small defect clusters. The effect of grain size on defect densities was investigated and found that defect densities were independent of grain size in the ultrafine and nanocrystalline region (60–400 nm). These results were compared to other heavy ion irradiation studies of structural materials. - Graphical abstract: Bright-field TEM micrographs and defect densities of UF and NC tungsten grains irradiated with a) Si{sup +} {sup 2} at 1.03 dpa: 1) 140 nm — 7.2 × 10{sup −} {sup 3} defects/nm{sup 2}, 2) 122 nm — 6.9 × 10{sup −} {sup 3} defects/nm{sup 2}, 3) 63 nm — 4.7 × 10{sup −} {sup 3} defects/nm{sup 2}, and 4) 367 nm — 6.4 × 10{sup −} {sup 3} defects/nm{sup 2}; b) Cu{sup +} {sup 3} to 3.79 dpa: 1) 228 nm — 4.3 × 10{sup −} {sup 3} defects/nm{sup 2}; 2) 202 nm — 5.9 × 10{sup −} {sup 3} defects/nm{sup 2}; and 3) 137 nm — 6.1 × 10{sup −} {sup 3} defects/nm{sup 2}; and c) W{sup +} {sup 4} to 5.72 dpa: 1) 372 nm — 2.3 × 10{sup −} {sup 3} defects/nm{sup 2} and 2) 128 nm — 4.5 × 10{sup −} {sup 3} defects/nm{sup 2}. - Highlights: • Heavy ion irradiations were performed on UF and NC grained tungsten. • Irradiations were performed with 3 MeV (Si{sup 2} {sup +}, Cu{sup 3} {sup +} and W{sup 4} {sup +}) ions at RT. • Defect density vs. dpa demonstrated four different stages in the case of W{sup 4} {sup +} irradiation. • Defect coalescence and absorption by the grain boundaries were observed after a dose of 3 dpa during W{sup 4} {sup +} irradiation. • No correlation existed between the grain width and the defect density for the UF and NC region.

36 MATERIALS SCIENCE↗