Search NASA⌕ Search

Engineering topics

Hattar, Khalid

Publications and source records attributed to Hattar, Khalid.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Tiny Bubbles: Combined HR(S)TEM and 4D-STEM Analysis of Sub-Nanometer He Bubbles in Au

Irradiation produces a distribution of defect sizes in materials, with the smallest defects often below one nanometer in size and approaching the scale of a single unit cell in metals. While high-resolution scanning transmission electron microscopy (STEM)-based imaging can directly image structures at this level, techniques such as four-dimensional STEM (4D-STEM) enable characterization of materials across large fields of view, capturing a more representative volume that can be valuable for quantifying defects, their distributions, and the associated strain fields. Here we present a combined HRSTEM and 4D-STEM approach to study the model system of He bubble implantation in an Au thin film. The present work is of general interest for the study of materials in extreme environments, as it demonstrates an effective way to characterize even the tiniest sub-nanometer sized He bubbles in addition to larger irradiation defects.

atomic-resolution STEM↗
DOE OSTI2024

Creep and failure at metal-oxide interfaces

Small-scale bicrystal creep experiments were performed on contacts formed via in situ high-temperature diffusion bonding of metal-oxide interfaces including Ag-ZrO 2 , Pd-ZrO 2 , Pt-ZrO 2 , and Ag-high entropy oxide. This work characterizes deformation and failure at metal-oxide interfaces during mechanical loading. Interfacial sliding can be activated easily, while tensile interfacial creep was not observed at any condition of stress or temperature measured. Plastic strain, instead, localizes within the metal under tensile loading. A variety of mechanisms for plastic strain occur in the metal including lattice dislocation-mediated plasticity, twinning, low-angle grain boundary formation, and low-angle grain boundary creep. Surface and low-angle grain boundary diffusion occur under conditions where no metal-oxide tensile creep is observed, highlighting the significant differences in their interfacial mechanical response. High-temperature interfacial failure occurs when the mean curvature at the contact neck is approximately zero and the applied stresses comparable to brittle fracture stresses. The brittle fracture stresses were measured to be σ ƒ = 180 ± 90 MPa at the Ag-ZrO 2 interface at 225 °C, σ ƒ = 460 ± 160 MPa at the Pd-ZrO 2 interface at 680 °C, and σ ƒ = 640 ± 440 MPa at the Pt-ZrO 2 interface at 1010 °C.

Creep↗
DOE OSTI2024

The Isotopic Limit of Recycling

Despite advances in recycling technologies and practices, the world still mostly operates on a once-through materials use cycle. The once-through approach to the materials supply chain cannot work into perpetuity. The vast majority of current recycling efforts focus on mechanical or chemical separation-based techniques and are often subsequently limited on the number of times a component can be recycled or upcycled. By looking at things from a particle physics and nuclear history perspective, we propose a thought experiment to determine the physical limit of recycling and propose subsequent limits and standards to evaluate all recycling efforts. This uncommon approach to analysis demonstrates that the current limits to recycling are not physical in nature but engineering.

Lang, Eric↗
DOE OSTI2024

Laterally Modulating Carrier Concentration by Ion Irradiation in CdO Thin Films for Mid‐IR Plasmonics

This report demonstrates tunable carrier densities in CdO thin films through local ion irradiation, providing lateral control of mid‐IR optical properties. Ion‐solid interactions produce donor‐like defects that boost electron concentrations from the practical minimum of 2.5 × 10 19 cm −3 to a maximum of 2.5 × 10 20 cm −3 by metered ion exposure. This range is achieved using He, N, Ar, or Au ions at 1–2.8 MeV; when normalized by displacements per atom, all ion species produce comparable results. Since CdO is well‐described by the Drude model, irradiation‐tuned carrier densities directly alter the infrared dielectric function, and in turn, mid‐infrared optical properties. Further, it is demonstrated that by combining irradiation with traditional lithography, CdO films expose to ions in the presence of 3‐µm thick, patterned photoresist exhibit lateral carrier density profiles with ≈400‐nm resolution. Scanning near‐field optical microscopy reveals sharp optical interfaces with almost no companion contrast in surface morphology, microstructure, or crystallinity. Finally, CdO lateral homostructures supporting surface plasmon polaritons (SPPs) are demonstrated whose dispersion relation can be tuned through periodic patterning in a monolithic platform by simple nanofabrication. Numerical simulations show these polaritons result from strong coupling between excitations at CdO plasma frequencies and SPPs supported by the platinum substrate.

cadmium oxide↗
DOE OSTI2024

Dynamic Deformation in Nuclear Graphite and Underlying Mechanisms

Time-dependent deformation in nuclear graphite is influenced by the creation and migration of radiation-induced defects in the reactor environment. This study investigates the role of pre-existing defects such as point defect clusters and Mrozowski cracks in nuclear graphite IG-110. Separate specimens were irradiated with a 2.8 MeV Au 2+ beam with a fluence of 4.38 × 10 14 cm −2 and an 8 MeV C 2+ beam with a fluence of 1.24 × 10 16 cm −2 . Microscopic specimens were either mechanically loaded inside a transmission electron microscope (TEM) or subjected to ex situ indentation-based creep loading. In situ TEM tests showed significant plasticity in regions highly localized around the Mrozowski cracks, resembling slip or ripplocation bands. Slip bands were also seen near regions without pre-existing defects but at very high stresses. Ex situ self-ion irradiation embrittled the specimens and decreased the creep displacement and rate, while heavy ion irradiation resulted in the opposite behavior. We hypothesize that the large-sized gold ions (compared to the carbon atoms) induced interplanar swelling as well as cross-plane channels for increased defect mobility. These findings illustrate the role of pre-existing defects in the dynamic relaxation of stresses during irradiation and the need for more studies into the radiation environment’s impact on the mechanical response of nuclear graphite.

creep deformation↗
DOE OSTI2024

Alloying effects on the microstructure and properties of laser additively manufactured tungsten materials

A large body of literature within the additive manufacturing (AM) community has focused on successfully creating stable tungsten (W) microstructures due to significant interest in their application for extreme environments. However, cracking and additional embrittling features at grain boundaries have resulted in poorly performing materials, stymying the application of AM as a manufacturing technique for W. Several alloying strategies, such as ceramic particles and ductile elements, have emerged with the promise to eliminate cracking while simultaneously enhancing stability against recrystallization. Here, in this work, we provide new insights regarding the defects and microstructural features that result from the introduction of ZrC for grain refinement and NiFe as a ductile reinforcement phase – in addition to the resulting thermophysical and mechanical properties. ZrC is shown to promote microstructural stability with increased hardness due to the formation of ZrO 2 dispersoids. Conversely, NiFe forms into micron-scale FCC phase regions within a BCC W matrix, producing enhanced toughness relative to pure AM W. A combination of these effects is realized in the WNiFe + ZrC system and demonstrates that complex chemical environments coupled with the tuning of AM microstructures provides an effective pathway for enabling laser AM W materials with enhanced stability and performance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Probing phonon focusing, thermomechanical behavior, and moiré patterns in van der Waals architectures using surface acoustic waves

Surface acoustic waves (SAWs) propagate along solid-air, solid-liquid, and solid-solid interfaces. Their characteristics depend on the elastic properties of the solid. Combining transmission electron microscopy (TEM) experiments with molecular dynamics (MD) simulations, we probe atomic environments around intrinsic defects that generate SAWs in vertically stacked two-dimensional (2D) bilayers of MoS 2 . Our joint experimental-simulation study provides insights into SAW-induced structural and dynamical changes and thermomechanical responses of MoS 2 bilayers. Using MD simulations, we compute mechanical properties from the SAW velocity and thermal conductivity from thermal diffusion of SAWs. The results for Young’s modulus and thermal conductivity of an MoS 2 monolayer are in good agreement with experiments. The presence of defects, such as nanopores which generate SAWs, reduces the thermal conductivity of 2D-MoS 2 by an order of magnitude. We also observe dramatic changes in moiré patterns, phonon focusing, and cuspidal structures on 2D-MoS 2 layers.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Using in situ UO 2 bicrystal sintering to understand grain boundary dislocation nucleation kinetics and creep

Capillary evolution at bicrystal UO 2 grain boundaries is characterized using in situ transmission electron microscopy. The discontinuous nature of the densification process, both particle rotation and axial strain, along with the large activation stress for densification support a hypothesis that grain boundary strain in UO 2 follows nucleation rate limited kinetics at low to intermediate stresses, that is, less than ≈ 10 8 PA. Further, the temperature dependence of the average activation stress for sintering agrees well with analysis of bulk sintering data and creep data reported within the literature when analyzed in the context of a grain boundary dislocation nucleation rate limited kinetic model.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The radiation instability of thermally stable nanocrystalline platinum gold

Here, recent experimentally validated alloy design theories have demonstrated nanocrystalline binary alloys that are stable against thermally induced grain growth. An open question is whether such thermal stability also translates to stability under irradiation. In this study, we investigate the response to heavy ion irradiation of a nanocrystalline platinum gold alloy that is known to be thermally stable from previous studies. Heavy ion irradiation was conducted at both room temperature and elevated temperatures on films of nanocrystalline platinum and platinum gold. Using scanning/transmission electron microscopy equipped with energy-dispersive spectroscopy and automated crystallographic orientation mapping, we observe substantial grain growth in the irradiated area compared to the controlled area beyond the range of heavy ions, as well as compositional redistribution under these conditions, and discuss mechanisms underpinning this instability. These findings highlight that grain boundary stability against one external stimulus, such as heat, does not always translate into grain boundary stability under other stimuli, such as displacement damage.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Interfacially Enhanced Superconductivity in Fe(Te,Se)/Bi 4 Te 3 Heterostructures

Realizing topological superconductivity by integrating high-transition-temperature (T C ) superconductors with topological insulators can open new paths for quantum computing applications. Here, a new approach is reported for increasing the superconducting transition temperature $T^{onset}_C$ by interfacing the unconventional superconductor Fe(Te,Se) with the topological insulator Bi–Te system in the low-Se doping regime, near where superconductivity vanishes in the bulk. The critical finding is that the $T^{onset}_C$ of Fe(Te,Se) increases from nominally non-superconducting to as high as 12.5 K when Bi 2 Te3 is replaced with the topological phase Bi 4 Te 3 . Interfacing Fe(Te,Se) with Bi4Te3 is also found to be critical for stabilizing superconductivity in monolayer films where $T^{onset}_C$ can be as high as 6 K. Measurements of the electronic and crystalline structure of the Bi 4 Te 3 layer reveal that a large electron transfer, epitaxial strain, and novel chemical reduction processes are critical factors for the enhancement of superconductivity. This novel route for enhancing T C in an important epitaxial system provides new insight on the nature of interfacial superconductivity and a platform to identify and utilize new electronic phases.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2024

Inducing a tunable skyrmion-antiskyrmion system through ion beam modification of FeGe films

Abstract Skyrmions and antiskyrmions are nanoscale swirling textures of magnetic moments formed by chiral interactions between atomic spins in magnetic noncentrosymmetric materials and multilayer films with broken inversion symmetry. These quasiparticles are of interest for use as information carriers in next-generation, low-energy spintronic applications. To develop skyrmion-based memory and logic, we must understand skyrmion-defect interactions with two main goals—determining how skyrmions navigate intrinsic material defects and determining how to engineer disorder for optimal device operation. Here, we introduce a tunable means of creating a skyrmion-antiskyrmion system by engineering the disorder landscape in FeGe using ion irradiation. Specifically, we irradiate epitaxial B20-phase FeGe films with 2.8 MeV Au 4+ ions at varying fluences, inducing amorphous regions within the crystalline matrix. Using low-temperature electrical transport and magnetization measurements, we observe a strong topological Hall effect with a double-peak feature that serves as a signature of skyrmions and antiskyrmions. These results are a step towards the development of information storage devices that use skyrmions and antiskyrmions as storage bits, and our system may serve as a testbed for theoretically predicted phenomena in skyrmion-antiskyrmion crystals.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2024

Compositionally complex carbide ceramics: A perspective on irradiation damage

Extensive experimental and computational studies have demonstrated outstanding physical and chemical properties of the novel materials of compositionally complex carbides (CCCs), enabling their promising applications in advanced fission and fusion energy systems. This perspective provides a comprehensive overview of radiation damage behavior reported in the literature to understand the fundamental mechanisms related to the impact of multi-principal metal components on phase stability, irradiation-induced defect clusters, irradiation hardening, and thermal conductivity of compositionally complex carbides. Several future research directions are recommended to critically evaluate the feasibility of designing and developing new ceramic materials for extreme environments using the transformative “multi-principal component” concept. Compared to the existing materials for nuclear applications including stainless steels, nickel alloys, ZrC, SiC, and potentially high-entropy alloys, as well as certain other compositionally complex ceramic families. CCCs appear to be more resistant to amorphization, growth of irradiation defect clusters, and void swelling.

36 MATERIALS SCIENCE↗