Engineering topics

Hattis, Philip D.

Publications and source records attributed to Hattis, Philip D..

6 records

NASA NTRS1992

Evaluation of some significant issues affecting trajectory and control management for air-breathing hypersonic vehicles

Horizontal takeoff airbreathing-propulsion launch vehicles require near-optimal guidance and control which takes into account performance sensitivities to atmospheric characteristics while satisfying physically-derived operational constraints. A generic trajectory/control analysis tool that deepens insight into these considerations has been applied to two versions of a winged-cone vehicle model. Information that is critical to the design and trajectory of these vehicles is derived, and several unusual characteristics of the airbreathing propulsion model are shown to have potentially substantial effects on vehicle dynamics.

Hattis, Philip D.↗

NASA NTRS1992

Air-breathing hypersonic vehicle guidance and control studies: An integrated trajectory/control analysis methodology, phase 2

An integrated trajectory/control analysis algorithm has been used to generate trajectories and desired control strategies for two different hypersonic air-breathing vehicle models and orbit targets. Both models used cubic spline curve fit tabulated winged-cone accelerator vehicle representations. Near-fuel-optimal, horizontal takeoff trajectories, imposing a dynamic pressure limit of 1000 psf, were developed. The first model analysis case involved a polar orbit and included the dynamic effects of using elevons to maintain longitudinal trim. Analysis results indicated problems with the adequacy of the propulsion model and highlighted dynamic pressure/altitude instabilities when using vehicle angle of attack as a control variable. Also, the magnitude of computed elevon deflections to maintain trim suggested a need for alternative pitch moment management strategies. The second analysis case was reformulated to use vehicle pitch attitude relative to the local vertical as the control variable. A new, more realistic, air-breathing propulsion model was incorporated. Pitch trim calculations were dropped and an equatorial orbit was specified. Changes in flight characteristics due to the new propulsion model have been identified. Flight regimes demanding rapid attitude changes have been noted. Also, some issues that would affect design of closed-loop controllers were ascertained.

Hattis, Philip D.↗

NASA NTRS1991

Integrated trajectory and control analysis for generic hypersonic vehicles

A tool which supports integrated assessment of air-breathing hypersonic vehicle trajectory management and control strategy has been developed by Hattis and Malchow (1991). Using a two-point boundary value problem solution technique, the tool can construct an entire near-minimum-fuel trajectory and desired control strategy from takeoff to orbit, while satisfying physically derived inequality constraints and while achieving efficient propulsive mode phasing. A strategy is also formulated to construct preliminary trajectory and control history representations with less computational burden than required for the overall flight profile assessment. A tabulated example hypersonic vehicle model has been used to demonstrate the integrated analysis methodology. To assure good numerical behavior when the algorithm uses tabulated model data, a multidimensional cubic spline curve smoothing routine has been developed. A dynamic-pressure-constrained, near-fuel-optimal trajectory was computed to provide examples of information that the methodology can provide. Previously unspecified propulsive discontinuities were located, flight regimes demanding rapid attitude changes were identified, available and closed-loop controller authority was ascertained, and inadequacies in vehicle and specific subsystem model representations were determined.

Hattis, Philip D.↗

NASA NTRS1991

Air-breathing hypersonic vehicle guidance and control studies; An integrated trajectory/control analysis methodology: Phase 1

A tool which generates optimal trajectory/control histories in an integrated manner is generically adapted to the treatment of single-stage-to-orbit air-breathing hypersonic vehicles. The methodology is implemented as a two point boundary value problem solution technique. Its use permits an assessment of an entire near-minimum-fuel trajectory and desired control strategy from takeoff to orbit while satisfying physically derived inequality constraints and while achieving efficient propulsive mode phasing. A simpler analysis strategy that partitions the trajectory into several boundary condition matched segments is also included to construct preliminary trajectory and control history representations with less computational burden than is required for the overall flight profile assessment. A demonstration was accomplished using a tabulated example (winged-cone accelerator) vehicle model that is combined with a newly developed multidimensional cubic spline data smoothing routine. A constrained near-fuel-optimal trajectory, imposing a dynamic pressure limit of 1000 psf, was developed from horizontal takeoff to 20,000 ft/sec relative air speed while aiming for a polar orbit. Previously unspecified propulsive discontinuities were located. Flight regimes demanding rapid attitude changes were identified, dictating control effector and closed-loop controller authority was ascertained after evaluating effector use for vehicle trim. Also, inadequacies in vehicle model representations and specific subsystem models with insufficient fidelity were determined based on unusual control characteristics and/or excessive sensitivity to uncertainty.

Hattis, Philip D.↗

NASA NTRS1989

Predictive Attitude Maintenance For A Space Station

Paper provides mathematical basis for predictive management of angular momenta of control-moment gyroscopes (CMG's) to control attitude of orbiting space station. Numerical results presented for pitch control of proposed power-tower space station. Based on prior orbit history and mathematical model of density of atmosphere, predictions made of requirements on dumping and storage of angular momentum in relation to current loading state of CMG's and to acceptable attitude tolerances.

Hattis, Philip D.↗

NASA NTRS1987

Shuttle orbit flight control design lessons - Direction for Space Station

The Space Shuttle orbit flight control system, which operates during all exo-atmospheric flight phases, has successfully met operational requirements. Many design integration and operational issues that required resolution during development and testing provide an experience base that will benefit the development of future space systems, particularly the Space Station. To this end, the applicable Shuttle and Space Station hardware/software is reviewed with some perspective provided on how current design groundrules were derived and how issues that affected the Shuttle orbit control system design are a pathway for the Space Station. Some of the most significant lessons learned from the Shuttle are summarized, with a discussion of the effect of performance and design of hardware, including the data processing system on software structures and usage procedures. Crew interface issues and important results from man-in-the-loop tests are summarized. Problems resulting from trying to meet difficult orbital operational objectives, including some sophisticated payload operations are characterized. Several proposed Shuttle flight control design improvements, developed in response to some of the lessons learned so far, are identified. Potential application of the Shuttle design lessons and new control technologies to the Space Station are discussed.

Cox, Kenneth J.↗