Asymmetric chloride-mediated electrochemical process for CO 2 removal from oceanwater
CO 2 is removed from oceanwater acidified during chloride-mediated electrochemically modulated reaction of bismuth electrodes.
Kim, Seoni↗
Engineering topics
Hatton, T. Alan
Publications and source records attributed to Hatton, T. Alan.
Electrochemical direct air capture of CO 2 using neutral red as reversible redox-active material
Direct air capture of carbon dioxide is a viable option for the mitigation of CO 2 emissions and their impact on global climate change. Conventional processes for carbon capture from ambient air require 230 to 800 kJ thermal per mole of CO 2 , which accounts for most of the total cost of capture. Here, we demonstrate electrochemical direct air capture using neutral red as a redox-active material in an aqueous solution enabled by the inclusion of nicotinamide as a hydrotropic solubilizing agent. The electrochemical system demonstrates a high electron utilization of 0.71 in a continuous flow cell with an estimated minimum work of 35 kJ e per mole of CO 2 from 15% CO 2 . Further exploration using ambient air (410 ppm CO 2 in the presence of 20% oxygen) as a feed gas shows electron utilization of 0.38 in a continuous flow cell to provide an estimated minimum work of 65 kJ e per mole of CO 2 .
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Nondimensional Analysis of a Hollow Fiber Membrane Contactor for Direct Air Capture
Not provided.
Engineering↗
Improved CO 2 Capture Performance of Electrochemically Mediated Amine Regeneration Processes with Ionic Surfactant Additives
For the effective reduction of global CO 2 emissions, it is essential to develop and deploy efficient and cost-effective technologies for CO 2 capture, especially from large point sources. We recently developed an electrochemically mediated amine regeneration (EMAR) system to replace traditional thermal desorption for the capture of CO 2 from post-combustion flue gases. Despite EMAR effectiveness on a laboratory scale, concerns regarding the high gas-to-liquid ratio in the electrochemical cell and long-term instability of the electrodes need to be addressed before further scale-up of the process to a pilot plant and beyond can be entertained. Accordingly, we investigated the effect of using sodium dodecyl sulfate (SDS) as an anionic surfactant and dodecyltrimethylammonium bromide (DTAB) as a cationic surfactant on the process operation. It was found that it is advantageous to use an anionic surfactant for a system such as EMAR that contains hydrophilic electrodes and a positively charged electrochemically active species. The overall cell resistance was notably reduced when SDS anionic surfactant was used. The precipitation of copper particles observed in the anode outlet when no surfactant was used was effectively avoided when SDS was added to the electrolyte, resulting in electrode stability. In addition, smaller gas bubbles were produced in the presence of the SDS surfactant, which resulted in less blockage of the electrode by the gas with a resultant lower cell potential under constant current conditions, driving more efficient CO 2 desorption. This led to an ~25% reduction in the electrochemical energy requirement, the lowest ever achieved experimentally for the EMAR process. Altogether, the addition of a very low concentration of SDS resulted in the successful circumvention of the important problems faced by the EMAR system regarding further scale-up.
36 MATERIALS SCIENCE↗
Technoeconomic Analysis of the Electrochemically Mediated Amine Regeneration CO 2 Capture Process
The electrochemically mediated amine regeneration (EMAR) process presents an alternative route to the conventional thermal amine regeneration for carbon capture from a flue gas source. In this study, we conducted an economic analysis on the EMAR system for postcombustion CO2 capture from a 550 MWe power plant capturing 3.1 MtCO2 annually and from a mini steel mill with annual capture close to 170 ktCO2. We followed the recommendation of the National Energy Technology Laboratory (NETL) 2010 report to estimate the cost of CO2 avoided ([$/tCO2]). Detailed cost modeling of the electrochemical separation stage was conducted. This is integrated with the entire process flowsheet (e.g., including absorber, compressor, pumps, and other auxiliary equipment). Here, we identified the membrane cost as the dominant capital cost for the electrochemical separation train. At a membrane unit price of less than 10/m2, the CO2 capture cost can be reduced to below 50/tCO2 with optimized process conditions (e.g., desorption pressure and utilization of waste heat). Improvements in process design, cell construction, and solvent formulation may lead to additional reductions in the CO2 capture cost.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
An Electrochemically Mediated Amine Regeneration Process with a Mixed Absorbent for Postcombustion CO 2 Capture
Electrochemically mediated amine regeneration (EMAR) was recently developed to avoid the use of thermal means to release CO2 captured from postcombustion flue gas in the benchmark amine process. To address concerns related to the high vapor pressure of ethylenediamine (EDA) as the primary amine used in EMAR, a mixture of EDA and aminoethylethanolamine (AEEA) was investigated. The properties of the mixed amine systems, including the absorption rates, electrolyte pH and conductivity, and CO2 capacity, were evaluated in comparison with those of solely EDA. The mixed amine system had similar properties to that of EDA, indicating no significant changes would be necessary for the future implementation of the EMAR process with mixed amines as opposed to that with just EDA. The electrochemical performance of the mixed amines in terms of the cell voltage, gas desorption rate, electron utilization, and energetics was also investigated. A 50/50 mixture of EDA and AEEA displayed the lowest energetics: ~10% lower than that of 100% EDA. With this mixture, a continuous EMAR process, in which the absorption column was connected to the electrochemical cell as the desorption stage, was tested over 100 h. The cell voltage was very stable and there was a steady gas output close to theoretical values. The desorbed gas was further analyzed and found to be 100% CO2, confirming no evaporation of the amine. The mixed absorbent composition was also characterized using titration and nuclear magnetic resonance (NMR) spectroscopy, and the results showed no amine degradation. Furthermore, these findings that demonstrate a stable, low vapor pressure absorbent with improved energetics are promising and could be a guideline for the future development of EMAR for CO2 capture from flue gas and other sources.
54 ENVIRONMENTAL SCIENCES↗
Flue Gas CO 2 Capture via Electrochemically Mediated Amine Regeneration: Desorption Unit Design and Analysis
We analyzed the performance of an electrochemical desorption unit to be implemented in an electrochemically mediated amine regeneration (EMAR) process, which separates CO 2 and regenerates the amine upon modulation of a targeted species that complexes with the amine molecules. Using a simplified one-dimensional boundary layer model, we combined the kinetic expressions of the faradaic reactions with mass transfer effects to analyze the polarization behavior of the flow cell. Mass transfer limitations become dominant at high current densities, leading to increases in energy consumption. An understanding of scaling laws with key parameters, such as the Sherwood number, is required to achieve high power operation with minimal mass transfer losses. Because the EMAR chemistry is sensitive to temperature, heat distribution in the unit is also examined. Our results indicate that the desorption performance increases with addition of a high-temperature heat source. Additionally, incorporation of membrane crossover suggests energy losses because of diffusion and migration of active species. Furthermore, these findings inform on scaling laws for at-scale desorber design and provide a model for scaling up the EMAR system for larger scale operations.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
CO 2 Capture Using Electrochemically Mediated Amine Regeneration
We describe the current status of our research on, and the development of, the Electrochemically Mediated Amine Regeneration (EMAR) process for the capture of CO2 from flue gases. The absorption step in the EMAR process is the same as in the widely used amine process, but the desorption step is accomplished electrochemically as opposed to by a thermal swing used in the amine process. Our laboratory unit has operated continuously for over 200 h, spanning 130 absorption/desorption cycles. We have established an understanding of the thermodynamics of the EMAR process and provided engineering estimates of key features (energetics and sizing) of this technology. The EMAR system does not rely on steam integration, making it a truly plug-and-play unit that can be easily deployed for a range of applications. The EMAR system can also be scaled-down for distributed, modular, and small-scale operations (e.g., stainless steel mini-mills, etc.). Here, results to date indicate that the EMAR process has the potential to be a viable option for post-combustion CO2 capture.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
A Fluorescence Recovery After Photobleaching (FRAP) Technique for the Measurement of Solute Transport Across Surfactant-Laden Interfaces
The technique of Fluorescence Recovery After Photobleaching (FRAP) has been applied to the measurement of interfacial transport in two-phase systems. FRAP exploits the loss of fluorescence exhibited by certain fluorophores when over-stimulated (photobleached), so that a two-phase system, originally at equilibrium, can be perturbed without disturbing the interface by strong light from an argon-ion laser and its recovery monitored by a microscope-mounted CCD camera as it relaxes to a new equilibrium. During this relaxation, the concentration profiles of the probe solute are measured on both sides of the interface as a function of time, yielding information about the transport characteristics of the system. To minimize the size of the meniscus between the two phases, a photolithography technique is used to selectively treat the glass walls of the cell in which the phases are contained. This allows concentration measurements to be made very close to the interface and increases the sensitivity of the FRAP technique.
Browne, Edward P.↗
Measurement of resistance to solute transport across surfactant-laden interfaces using a Fluorescence Recovery After Photobleaching (FRAP) technique
A noninvasive fluorescence recovery after photobleaching (FRAP) technique is under development to measure interfacial transport in two phase systems without disturbing the interface. The concentration profiles of a probe solute are measured in both sides of the interface by argon-ion laser, and the system relaxation is then monitored by a microscope-mounted CCD camera.
Browne, Edward P.↗