Engineering topics

Haviland, J. K.

Publications and source records attributed to Haviland, J. K..

At least 19 records

NASA NTRS1991

Design of cryogenic tanks for space vehicles shell structures analytical modeling

The initial objective was to study the use of superplastically formed corrugated hat section stringers and frames in place of integrally machined stringers over separate frames for the tanks of large launch vehicles subjected to high buckling loads. The ALS was used as an example. The objective of the follow-on project was to study methods of designing shell structures subjected to severe combinations of structural loads and thermal gradients, with emphasis on new combinations of structural arrangements and materials. Typical applications would be to fuselage sections of high speed civil transports and to cryogenic tanks on the National Aerospace Plane.

Copper, Charles↗

NASA NTRS1985

Digital control system for space structure dampers

A digital controller was developed using an SKD-51 System Design Kit, which incorporates an 8031 microcontroller. The necessary interfaces were installed in the wire wrap area of the SKD-51 and a pulse width modulator was developed to drive the coil of the actuator. Also, control equations were developed, using floating-point arithmetic. The design of the digital control system is emphasized, and it is shown that, provided certain rules are followed, an adequate design can be achieved. It is recommended that the so-called w-plane design method be used, and that the time elapsed before output of the up-dated coil-force signal be kept as small as possible. However, the cycle time for the controller should be watched carefully, because very small values for this time can lead to digital noise.

Haviland, J. K.↗

NASA NTRS1984

Digital control system for space structural dampers

Digital control systems for space structural dampers, also referred to as inertia or proof-mass dampers are investigated. A damper concept is improved by adding a small taper to the proof-mass, and using a proximeter to determine position. Another damper using a three inch stroke rather than the standard one inch stroke is described. Provisions are made for a relative velocity feedback. In one approach, the digital controller is modified to accept the signal from a linear velocity transducer. In the other, the velocity feedback is included in the digital program. An overall system concept for the use of the dampers is presented.

Haviland, J. K.↗

NASA NTRS1984

Digital control system for space structural dampers

A recently developed concept for a damper was improved by adding a small taper to the proof-mass, and using a proximeter to determine position. Also, an experimental damper was built using a three-inch stroke in place of the standard one-inch stroke. The analog controller initially used was replaced by an independent digital controller slaved to a TRS-80 Model I computer, which also serves as a highly effective, low-cost development system. An overall system concept for the use of proof-mass dampers is presented.

Haviland, J. K.↗

NASA NTRS1983

Large space structure damping design

Several FORTRAN subroutines and programs were developed which compute complex eigenvalues of a damped system using different approaches, and which rescale mode shapes to unit generalized mass and make rigid bodies orthogonal to each other. An analytical proof of a Minimum Constrained Frequency Criterion (MCFC) for a single damper is presented. A method to minimize the effect of control spill-over for large space structures is proposed. The characteristic equation of an undamped system with a generalized control law is derived using reanalysis theory. This equation can be implemented in computer programs for efficient eigenvalue analysis or control quasi synthesis. Methods to control vibrations in large space structure are reviewed and analyzed. The resulting prototype, using electromagnetic actuator, is described.

Pilkey, W. D.↗

NASA NTRS1978

Unsteady loads due to propulsive lift configurations. Part A: Investigation of scaling laws

This study covered scaling laws, and pressure measurements made to determine details of the large scale jet structure and to verify scaling laws by direct comparison. The basis of comparison was a test facility at NASA Langley in which a JT-15D exhausted over a boilerplater airfoil surface to reproduce upper surface blowing conditions. A quarter scale model was built of this facility, using cold jets. A comparison between full scale and model pressure coefficient spectra, presented as functions of Strouhal numbers, showed fair agreement, however, a shift of spectral peaks was noted. This was not believed to be due to Mach number or Reynolds number effects, but did appear to be traceable to discrepancies in jet temperatures. A correction for jet temperature was then tried, similar to one used for far field noise prediction. This was found to correct the spectral peak discrepancy.

Morton, J. B.↗

NASA NTRS1978

Unsteady loads due to propulsive lift configurations. Part C: Development of experimental techniques for investigation of unsteady pressures behind a cold model jet

As part of an overall study of the scaling laws for the fluctuating pressures induced on the wings and flaps of STOL aircraft by jet engine impingement, an experimental investigation was made of the near field fluctuating pressures behind a cold circular jet, both when it was free and when it was impinging on a flat plate. Miniature static pressure probes were developed for measurements in the free jet and on the flat plate which were connected by plastic tubing to 1/8 inch microphones and acted as pressure transducers. Using a digital correlator together with an FFT program on the CDC 6400 computer, spectral densities, relative amplitudes, phase lags, and coherences were also obtained for the signals from pairs of these probes, and were used to calibrate these probes directly against microphones. This system of instrumentation was employed to obtain single point rms and third octave surveys of the static pressures in the free jet and on the surface of the plate.

Haviland, J. K.↗

NASA NTRS1978

Unsteady loads due to propulsive lift configurations. Part D: The development of an experimental facility for the investigation of scaling effects on propulsive lift configurations

The design and construction of an experimental facility for the investigation of scaling effects in propulsive lift configurations are described. The facility was modeled after an existing full size NASA facility which consisted of a coaxial turbofan jet engine with a rectangular nozzle in a blown surface configuration. The flow field of the model facility was examined with and without a simulated wing surface in place at several locations downstream of the nozzle exit plane. Emphasis was placed on obtaining pressure measurements which were made with static probes and surface pressure ports connected via plastic tubing to condenser microphones for fluctuating measurements. Several pressure spectra were compared with those obtained from the NASA facility, and were used in a preliminary evaluation of scaling laws.

Haviland, J. K.↗

NASA NTRS1977

Modelling techniques for jet impingement

A technique for testing scale models for the determination of fluctuating pressure loads due to jet impingement has been investigated using a quarter-scale model of a boilerplate test facility in which a JT-15D engine with a rectangular outer nozzle blows over a small curved airfoil representing the upper-surface of a wing. When model and full-scale spectra of fluctuating surface pressures are reduced to plots of pressure coefficient power-spectral density vs Strouhal number, moderate agreement is obtained, but a shift of spectral peaks is noted. However, when a correction for the ratio of average jet to ambient temperature is applied, the spectral peaks agree.

Haviland, J. K.↗

NASA NTRS1976

Calculation of subsonic and supersonic steady and unsteady aerodynamic forces using velocity potential aerodynamic elements

Expressions for calculation of subsonic and supersonic, steady and unsteady aerodynamic forces are derived, using the concept of aerodynamic elements applied to the downwash velocity potential method. Aerodynamic elements can be of arbitrary out of plane polygon shape, although numerical calculations are restricted to rectangular elements, and to the steady state case in the supersonic examples. It is suggested that the use of conforming, in place of rectangular elements, would give better results. Agreement with results for subsonic oscillating T tails is fair, but results do not converge as the number of collocation points is increased. This appears to be due to the form of expression used in the calculations. The methods derived are expected to facilitate automated flutter analysis on the computer. In particular, the aerodynamic element concept is consistent with finite element methods already used for structural analysis. The method is universal for the complete Mach number range, and, finally, the calculations can be arranged so that they do not have to be repeated completely for every reduced frequency.

Haviland, J. K.↗

NASA NTRS1976

Fluctuating pressures in flow fields of jets

The powered lift configurations under present development for STOL aircraft are the externally blown flap (EBF), involving direct jet impingement on the aircraft flaps, and the upper surface blown (USB), where the jet flow is attached on the upper surface of the wing and directed downwards. Towards the goal of developing scaling laws to predict unsteady loads imposed on the structural components of these STOL aircraft from small model tests, the near field fluctuating pressure behavior for the simplified cases of a round free cold jet and the same jet impinging on a flat plate was investigated. Examples are given of coherences, phase lags (giving convection velocities), and overall fluctuating pressure levels measured. The fluctuating pressure levels measured on the flat plate are compared to surface fluctuating pressure levels measured on full-scale powered-lift configuration models.

Schroeder, J. C.↗

NASA NTRS1976

Investigations of scaling laws for jet impingement

The statistical properties of tangential flows over surfaces were investigated by two techniques. In one, a laser-Doppler velocimeter was used in a smoke-laden jet to measure one-point statistical properties, including mean velocities, turbulent intensities, intermittencies, autocorrelations, and power spectral densities. In the other technique, free stream and surface pressure probes connected to 1/8 inch microphones were used to obtain single point rms and 1/3 octave pressures, as well as two point cross correlations, the latter being converted to auto spectra, amplitude ratios, phase lags, and coherences. The results of these studies support the vortex model of jets, give some insights into the effects of surface impingement, and confirm that jet diameter and velocity are the scaling parameters for circular jets, while Reynolds number is relatively unimportant.

Morton, J. B.↗

NASA NTRS1975

Unsteady loads due to propulsive lift configurations

The flow of a jet over an airfoil representative of upper surface blowing was studied using laser techniques. Experimental techniques were developed for the investigation of unsteady pressures behind a cold model jet. Construction of a 1/4 scale model of the 'Beach' test configuration was completed along with construction of a portable detector. The portable detector is used in conjunction with a laser to measure jet flows during tests on the 'Beach' facility. The detector incorporates both optical and electronic components.

Morton, J. B.↗

NASA NTRS1974

Topics in structural dynamics: Nonlinear unsteady transonic flows and Monte Carlo methods in acoustics

The results are reported of two unrelated studies. The first was an investigation of the formulation of the equations for non-uniform unsteady flows, by perturbation of an irrotational flow to obtain the linear Green's equation. The resulting integral equation was found to contain a kernel which could be expressed as the solution of the adjoint flow equation, a linear equation for small perturbations, but with non-constant coefficients determined by the steady flow conditions. It is believed that the non-uniform flow effects may prove important in transonic flutter, and that in such cases, the use of doublet type solutions of the wave equation would then prove to be erroneous. The second task covered an initial investigation into the use of the Monte Carlo method for solution of acoustical field problems. Computed results are given for a rectangular room problem, and for a problem involving a circular duct with a source located at the closed end.

Haviland, J. K.↗

NASA NTRS1973

Integral equation for small perturbations of irrotational flows

An investigation is conducted concerning the validity of analytical methods which are based on deriving an integral equation, taking into account small perturbations in the case of a nonuniform but irrotational flow. The results obtained apply to a wide Mach number range, but are restricted to small amplitude motions and to nonviscous flows. It is shown that the integral equation relating the unknown velocity potential to the known normal flow velocity can be derived from the appropriate Green's identity.

Haviland, J. K.↗

NASA NTRS1973

Monte Carlo applications to acoustical field solutions

The Monte Carlo technique is proposed for the determination of the acoustical pressure-time history at chosen points in a partial enclosure, the central idea of this technique being the tracing of acoustical rays. A statistical model is formulated and an algorithm for pressure is developed, the conformity of which is examined by two approaches and is shown to give the known results. The concepts that are developed are applied to the determination of the transient field due to a sound source in a homogeneous medium in a rectangular enclosure with perfect reflecting walls, and the results are compared with those presented by Mintzer based on the Laplace transform approach, as well as with a normal mode solution.

Haviland, J. K.↗

NASA NTRS1973

Downwash-velocity potential method for oscillating surfaces.

The application of the downwash-velocity potential method to the case of oscillating surfaces is developed, and calculated forces are given on rectangular airfoils of aspect ratio two rotating about midchord in subsonic flows. These are compared with other results published in the literature for reduced frequencies up to nine-tenths, and for Mach numbers up to nine-tenths. The concept of 'aerodynamic elements' is presented, the computed results representing three possible types of rectangular element.

Haviland, J. K.↗

NASA NTRS1972

Transport phenomena of reactive fluid flow in heterogeneous combustion processes.

A previously developed computer program was used to model two transient hybrid combustion processes involving tubes of solid Plexiglas. In the first study, representing combustion of a hybrid rocket, the oxidizing gas was oxygen, and calculations were continued sufficiently long to obtain steady-state values. Systematic variations were made in reaction rate constant, mass flow rate, and pressure, alternatively using constant and temperature dependent regression rate models for the fuel surface. Consistent results were obtained, as is evidenced by the values for the mass function of the reaction product and the flame temperature, for which plots are supplied. In the second study, fire initiation in a duct was studied, with an air mixture as the oxidizing gas. It was demonstrated that a satisfactory flame spread mechanism could be reproduced on the computer. In both of the above applications, the general, transient, two-dimensional conservation equations were represented, together with chemical reactions, solid-fuel interface conditions, and heat conduction in the solid fuel.

Hung, W. S. Y.↗