Engineering topics
Publications and source records attributed to Hays, Cameron.
Pyruvate-derived dialkoxyalkanoates (DAOAs) were synthesized in good yield using a mild protocol. Combustion performance and physical properties of DAOAs compare favorably to other low-carbon diesel fuels.
Polyoxymethylene ethers (POMEs) are a class of low-soot and high-cetane oxygenate oligomers of structure RO-(CH 2 O-) $n$ -R, with different chain lengths ($n$) and end-groups (R) that determine their diesel-like fuel properties. Commercial POMEs with methyl end-groups (MM-POME 3-6 ) exhibit undesirably low energy density and high-water solubility. A previous computational assessment indicated that the lower heating value (LHV) and water solubility for MM-POME 3-6 both improve upon end-group exchange with larger butyl, $iso$-butyl and $iso$-pentyl end-groups. Here, we expanded upon our initial trans-acetalization reaction that employed 1-butanol to install butyl end-groups to also include branched, higher carbon-number end-groups using $iso$-butanol and fusel oil as reagents. Additionally, these new products are termed $i$B*POME 1-6 , and FOil*POME 1-5 , respectively, and collectively referred to as R*POMEs. They possess the advantaged properties of the parent MM-POME 3-6 while exhibiting higher LHV (31 MJ kg -1 and 28 MJ kg -1 for $i$B*POME 1-6 , and FOil*POME 1-5 , respectively) and much reduced water solubility (2.7 g L -1 and 1 g L -1 for $i$B*POME 1-6 , and FOil*POME 1-5 , respectively). Additional fuel property analyses were performed using 20 vol% blends of the R*POMEs with a base diesel fuel. Overall, the greater energy density and decreased water solubility of the R*POMEs, as well as their synergistic blending with diesel at moderate blend levels, provide the greatest benefits to consumers and position this group of products as an environmentally friendlier blendstock alternative to the commercially available MM-POME 3-6 .
The multicomponent nature of and variability of biomass makes chemical upgrading via a single process stream to a single end use infeasible for most feedstocks. A more promising approach is to identify upgrading strategies (encompassing bioprocessing, catalysis, and separations) which valorize varied biomass fractions to distinct products to which each is best suited. A robust procedure to carry out this goal should incorporate comparison of various upgrading procedures as well as suitability of products to a slate of identified end uses. We applied this strategy to one biomass-derived feedstock, volatile fatty acids (VFAs) derived from wet waste arrested anaerobic digestion, by developing a computer program, VFA Upgrading to Liquid Transportation fUels Refinery Estimation (VULTURE) which evaluates VFA catalytic upgrading to liquid transportation fuels. VULTURE considers multiple separations, catalysis (ketonization, hydrogenation), and fuel application options, generating hundreds of candidate scenarios for a given VFA stream, then selects several promising strategies that optimize bio-content of products with properties best suited for target fuel types. We find that VFAs are upgraded most efficiently when separate light alcohol (C3-6) and heavy hydrocarbon or alcohol (C7-13) fractions are targeted to create gasoline and heavy-duty (diesel or jet) fuels or fuel blends. Surrogate property testing of VULTURE-recommended fuels reveals that most predictive models employed are robust, while rigorous process simulation shows that the simple unit operation assumptions used in VULTURE are largely accurate, especially for heavy-duty fuel synthesis. Techno-economic and life-cycle analyses show that VFA-derived fuels are profitable and have dramatically (=57%) lower carbon intensities than fossil analogs.
Biomass conversion to fuels and chemicals is crucial to decarbonization, but choosing an advantageous upgrading pathway out of many options is challenging. Rigorously evaluating all candidate pathways (process simulation, product property testing) requires a prohibitive amount of research effort; even simple upgrading schemes have hundreds of possible permutations. We present a method enabling high-throughput screening by approximating upgrading unit operations and drop-in compatibility of products (e.g., fuel properties) and apply it to volatile fatty acid (VFA) conversion to liquid transportation fuels via a MATLAB script, VFA Upgrading to Liquid Transportation fUels Refinery Estimation (VULTURE). VULTURE selects upgrading configurations that maximize fuel blend bio-derived content. We validate VULTURE's approximations through surrogate fuel property testing and process simulation. Techno-economic and life cycle analyses suggest that VFA upgrading processes down-selected by VULTURE are profitable and have low carbon intensities, demonstrating the potential for the strategy to accelerate process development timelines at decreased costs.
Underutilized wet waste is a promising feedstock for production of carbon-neutral or carbon-negative liquid transportation fuels. Arrested methanogenesis of wet wastes by microbes, which produces mixtures of C2-C8 carboxylic acids (volatile fatty acids, VFAs), is practiced industrially at a pilot scale and the VFA products can be catalytically upgraded to molecules suitable for use as transportation fuels (alcohols and alkanes) via sequential ketonization and hydrogenation, both steps of which have been demonstrated with high (>90%) yield at the lab scale. We present in this work a simulation-based decision-making framework which evaluates upgrading strategies of VFAs to alcohol- and hydrocarbon-based neat and blended diesel, jet, and gasoline fuels. The processes utilize sequential upgrading steps (ketonization and hydrogenation) accompanied by one distillation step (either separating VFAs before ketonization or alcohols after ketone hydrogenation) to form two liquid streams: a light alcohol stream best suited as a light-duty fuel and a heavy alcohol or hydrocarbon stream best suited as a diesel or jet fuel. Suitability of the liquid products as transportation fuels and maximum blending levels with petrofuels comes from simulation of critical fuel properties (boiling point, flash point, lower heating value, viscosity, melting point, water solubility, and cetane/octane number). Catalytic upgrading steps and fuel property mixing models used by the simulation are experimentally validated. We demonstrate the flexibility of the decision-making algorithm by evaluating processing scenarios for experimentally-observed VFA profiles with varied carbon chain length distributions. Processing scenarios are optimized for either maximum total renewable carbon utilization or production of heavy-duty (jet or diesel) fuels. We evaluate the economic viability and CO2 emissions of each proposed upgrading scenario using techno-economic and life cycle analyses. The decision-making framework developed in this work can also be used to down-select promising strategies for upgrading of other bio-based feedstocks to sustainable fuels and chemicals.
This study developed the design principle of bio-derived ether fuels with low soot emission and high reactivity based on an experiment-theory combined approach.
Methyl-terminated polyoxymethylene ethers (MM-POMEs), having the formula CH 3 O-(CH 2 O)n-CH 3 (n = 3-6), are a class of oxygenates with desirable diesel-like fuel properties including high cetane number and low soot formation. However, their low energy density and high water-solubility present barriers to their adoption. Both concerns were recently addressed by our research group by synthesizing a mixture of POME structures having butyl end-groups and n = 1-6, termed B*POME1-6. B*POME1-6 maintained the advantageous properties of the parent MM-POMEs, and exhibited improved energy density and most notably, dramatically decreased water solubility. For evaluation against a set of criteria for a blended diesel blendstock, a 20 vol% blend of B*POME1-6 with a base diesel fuel was investigated here. Oxidation stability, cetane number, sooting tendency, lubricity and conductivity were improved in the B*POME1-6 blend compared with the base diesel, while also maintaining the flash point, cloud point, energy density, viscosity, and boiling point requirements. The B*POME1-6 product demonstrated a synergistic blending behavior at 10 vol% and a linear blending behavior at 20-30 vol% blends, in agreement with similar POME blends at comparable blend levels. Finally, common environmental and toxicity models performed on B*POME1-6 component molecules suggested they have a greater propensity to partition into the water compartment compared to a common diesel surrogate, but with a lower tendency to bioaccumulate.
Supercritical methanol (SCM) solvolysis and catalysis has recently emerged as a promising pathway to produce gasoline-range light alcohols from woody biomass through staged depolymerization and hydro-deoxygenation (DHDO). Here, structure-property relationships of Cu"M"AlO x catalysts (M = Mg, Zr, and Ce) are examined for upgrading delignified hybrid poplar via SCM-DHDO. CuCeAlO x displays the highest activity, increasing the C 2 -C 7 alcohol production rate and selectivity by twofold in batch reactions, and >50% in semicontinuous reactions relative to the current state-of-the-art CuMgAlO x . The performance of CuCeAlOx is correlated with its high reducibility and acidity. Cu sintering and biogenic impurity poisoning are identified as possible deactivation mechanisms over 60 h of continuous testing. The gasoline-range SCM-DHDO products are comprised of primarily aliphatic alcohols that result in improved energy density and favorably reduced vapor pressure, relative to ethanol, with the tradeoff of nonsynergistic octane blending with conventional gasoline and lower oxidation stability. Overall, this work highlights the potential to produce suitable light oxygenates by SCM-DHDO processing for gasoline bioblendstock applications.
With the increasing pressure to decarbonize the transportation sector, exploring strategies that can reduce emissions from light-duty vehicles (LDV) has become critical. Bioblendstocks that allow for higher engine efficiency and fuel economy could complement vehicle electrification and help reach carbon neutrality by 2050. In this context, the potential of a mixture of iso-olefins as a bioblendstock was investigated for multimode boosted spark-ignition (SI)/advanced compression ignition (ACI) engine operation designed to achieve higher overall vehicle fuel economy. By establishing the relationship between the molecular structure of iso-olefins and research octane number (RON), octane sensitivity (S) (i.e., the difference between RON and motor octane number [MON]), and phi-sensitivity a dimethyl-hexenes rich olefins mixture (DMHROM) was identified as a preferred blendstock for SI/ACI combustion engines. Here, a pathway for DMHROM production from biomass-derived ethanol was developed and scaled up. More than 1 gallon of DMHROM blendstock was produced for fuel properties assessment including engine testing. Measurements in a Cooperative Fuel Research Engine showed that the DMHROM blendstock possesses a RON of 94 and S of 13.5, and blends synergistically. Rapid compression machine tests coupled with single-cylinder gasoline direct injection engine measurements demonstrated the 20 vol.% DMHROM blend has higher phi-sensitivity than an olefin-free gasoline base fuel and a typical California Reformulated Gasoline Blendstock for Oxygenate Blending (CARBOB) gasoline fuel. These results demonstrate the potential of DMHROM for improving gasoline fuel performance and quality for operation under ACI conditions. The effectiveness of the aftertreatment system in mitigating emissions was verified and showed that the pure DMHROM blendstock and 20 vol.% blend would not increase non-methane organic gases, NO x , and carbon monoxide (CO) emissions. The DMHROM blendstock was found to slightly decrease sooting tendency when added to a gasoline-base fuel (i.e., ~6% reduction at 20 vol.% blending level). Oxidation stability and lubricant compatibility were both confirmed for the 20 vol.% blend. Overall, these results demonstrate that dimethyl-hexenes have potential for improving engine efficiency and fuel economy while meeting emissions regulations and ASTM specifications for gasoline fuel.
Methyl-terminated polyoxymethylene ethers (MM-POMEs), having the formula CH3O–(CH2O)n–CH3 (n = 3–5), are a high-cetane, low-sooting group of oxygenates that have recently attracted attention as potential diesel blendstocks. Despite these attractive fuel properties, MM-POMEs have shortcomings due to their low energy density and high water solubility. Guided by a computational fuel property assessment for POMEs with longer end-groups, the most promising improvements in the desired compression ignition fuel properties were observed for butyl-terminated POMEs. Here, an acid-catalyzed transacetalization reaction was developed to exchange the methyl end-groups of MM-POMEs (n = 3–6) with butyl end-groups. The reaction utilizes an ion-exchange resin as the acid catalyst at mild reaction conditions of 60 °C and atmospheric pressure. Approximately 100 mL of butyl-exchanged POMEs in the diesel boiling range were produced, enabling laboratory-scale fuel property testing. The butyl-terminated POME mixture possesses the advantaged fuel properties of the parent MM-POMEs (low-soot, high-cetane) while exhibiting improved energy density (lower heating value (LHV) of 30 MJ/kg) and substantially reduced water solubility (7.3 g/L) compared to the parent MM-POME mixture (LHV of 19 MJ/kg , water solubility of 258 g/L).
Significance To meet the growing demand for sustainable aviation fuels (SAF), conversion pathways are needed that leverage wet waste carbon and meet jet fuel property specifications. Here, we demonstrate SAF production from food waste–derived volatile fatty acids (VFA) by targeting normal paraffins for a near-term path to market and branched isoparaffins to increase the renewable content long term. Combining these distinct paraffin structures was shown to synergistically improve VFA-SAF flash point and viscosity to increase the renewable blend limit to 70%. Life cycle analysis shows the dramatic impact on the carbon footprint if food waste is diverted from landfills to produce VFA-SAF, highlighting the potential to meet jet fuel safety, operability, and environmental goals.