Search NASA⌕ Search

Engineering topics

He, Xin

Publications and source records attributed to He, Xin.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Thermomechanical Modeling and Analysis of a High-Temperature Light Trapping Planar Cavity Receiver

Solar energy harnessed through concentrating solar power (CSP) systems offers a promising path to sustainable energy production, with the efficiency and longevity of these systems relying on key components like solar receivers. This study analyzes the thermomechanical behavior of an innovative enclosed light-trapping solar receiver optimized for particle heating applications. The receiver utilizes sheet metal alloys to form enclosed cavities that reflect and trap incoming solar flux, as well as enclosed channels that contain fluidized particle beds absorbing solar heat. Finite element analysis (FEA) is applied to predict the receiver's thermomechanical performance under extreme solar flux conditions. Temperature distributions from a thermal model simulating a multi-panel assembly at steady state are input into the FEA thermomechanical model for stress analysis. A key aspect of the analysis focuses on evaluating creep-fatigue damage, with a design target of achieving a 30- year service life. Various stress relief techniques are also proposed to extend the receiver's service life. The results highlight the significant impact of the particle-to-wall heat transfer coefficients (HTCs), ranging from 800 W/m2*K to 1400 W/m2*K. The 800 W/m2*K case shows a maximum von Mises stress of 164 MPa, while the 1400 W/m2*K case reduces it to 150 MPa. The creep life increases from 4,000 hrs in the 800 W/m2*K case to over 100,000 hrs in the 1400 W/m2*K case with Inconel 740H used, indicating that higher HTCs reduce stress and extend lifespan. This research advances the design of high-efficiency, low-stress solar receivers for particle-based thermal energy storage in CSP and industrial heating applications.

concentrating solar power↗
DOE OSTI2024

Development of High Temperature (>700°C) Molten Salt Pump Technology for Generation 3 Solar Power Tower Systems

Bearings are required for long-shafted pumps historically used in concentrating solar thermal power applications. For molten chloride salts, bearings for such service conditions are not commercially available, nor has a design been demonstrated to work. Therefore, a project was sponsored by the Department of Energy’s Solar Energy Technologies Office for the development and demonstration of a submerged bearing for use in chloride salt pumps. This project’s tasks covered the tribological testing of candidate materials and the design, fabrication, testing, and post-test analysis of full-scale salt-compatible bearings. This work expands upon previous work. The effects of potential particulate in the salt were investigated through tribological bench testing. Through 11 tests, the MgO particulate size and concentration in a molten chloride salt were varied, and the effects on friction, wear rate, and wear characteristics were recorded. Novel journal bearings for chloride salt service were designed and fabricated based on these results. The bearings were of a relevant scale (i.e., for a 1.5 in. pump shaft) to demonstrate the technology with respect to further scale-up. The bearings were made of Haynes 244 and Yttria Partially Stabilized Zirconia. A custom bearing test rig, salt tanks, and associated infrastructure (e.g., heaters, tanks, transfer lines, gas flow control) were designed, procured, and installed. A few issues were encountered in the system fabrication process, resulting in delay of the project schedule. The system was successfully fabricated and assembled. Heating, cover gas, and pump motor systems were integrated into the control logic. This progress of the bearing test system represents a significant step forward towards demonstrating this promising technology. Nevertheless, the project ended before testing of the full-scale bearings could be performed.

14 SOLAR ENERGY↗
DOE OSTI2024

Simulating Wind-Driven Loading on PV Systems

As PV modules continue to trend toward larger, thinner, and more flexible forms they grow more susceptible to damage from dynamic wind loading. As a result, understanding the impact of wind on PV systems, particularly when mounted on compliant solar-tracking hardware, and identifying robust, stable array layouts and stow strategies is becoming increasingly important for the PV community. We are developing an open-source software package, PVade (PV aerodynamic design engineering), to simulate the cascading fluid-structure interaction that occurs within single-axis, solar-tracking arrays to enable researchers to test hardware, layout, and tracker control changes, leading to enhanced stability and a reduction in wind-driven damage. We will give an overview of the PVade software and present the latest outcomes from our ongoing validation campaign in which we compare time series and statistical structural responses with field data. From there, we will present simulated results from a larger, multi-row array and highlight the effect of varying tracker angles on stability and the differences between positive and negative tilt angles.

fluid↗
DOE OSTI2024

A Simulation and Optimization Framework for Managing Wind-Driven Loading on PV Systems

As PV modules continue to trend toward larger, thinner, and more flexible forms they grow more susceptible to damage from dynamic wind loading. As a result, understanding the impact of wind on PV systems, particularly when mounted on solar-tracking hardware, and identifying robust, stable array layouts and stow strategies is becoming increasingly important for the PV community. We are developing an open-source software package, PVade (PV aerodynamic design engineering), to simulate the cascading fluid-structure interaction that occurs within solar-tracking arrays to enable researchers to test hardware, layout, and tracker control changes, leading to enhanced stability and a reduction in wind-driven damage. We will give an overview of the PVade software and present the latest outcomes from our ongoing validation campaign in which we compare statistical structural responses with field data. From there, we will present simulated results from a larger, multi-row array and highlight the effect of varying tracker angles on stability as measured by both acceleration and deformation, focusing on the stability differences between positive and negative tilt angles.

fluid structure interaction↗
DOE OSTI2024

Comparison of Eco-Friendly Ionic Liquids and Commercial Bio-Derived Lubricant Additives in Terms of Tribological Performance and Aquatic Toxicity

Approximately half of the lubricants sold globally find their way into the environment. The need for Environmentally Acceptable Lubricants (EALs) is gaining increased recognition. A lubricant is composed of a base oil and multiple functional additives. The literature has been focused on EAL base oils, with much less attention given to eco-friendly additives. This study presents the tribological performance and aquatic toxicity of four short-chain phosphonium-phosphate and ammonium-phosphate ionic liquids (ILs) as candidate anti-wear and friction-reducing additives for EALs. The results are benchmarked against those of four commercial bio-derived additives. The four ILs, at a mere 0.5 wt% concentration in a synthetic ester, demonstrated a 30–40% friction reduction and >99% wear reduction, superior to the commercial baselines. More impressively, all four ILs showed significantly lower toxicity than the bio-derived products. In an EPA-standard chronic aquatic toxicity test, the sensitive model organism, Ceriodaphnia dubia, had 90–100% survival when exposed to the ILs but 0% survival in exposure to the bio-derived products at the same concentration. This study offers scientific insights for the future development of eco-friendly ILs as lubricant additives.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Mitigating municipal solid waste fouling in biofuel conversion via screw surface modifications

Here, municipal solid waste (MSW)'s 40–60 % carbon content makes it a feedstock for biofuel production via pyrolysis. One challenge in the conversion process is MSW fouling due to thermal decomposition. The accumulated deposit on the injection screw often leads to plugging and constriction. This study examined the morphology and composition of the MSW fouling deposit and conducted a thermal simulation to understand the temperature gradience of the injection screw. Surface modifications including smoothening and anti-adhesion coating were proposed for the injection screw to address the deposit problem. For evaluating the candidate mitigations, a bench-scale fouling test was developed with the gas environment, temperature, and sliding speed relevant to the contact interface between the MSW particles and the screw. Results suggested that a smoother screw surface could reduce the grip and a non-metallic coating with a lower surface energy could decrease adhesion, consequently leading to less fouling. Specifically, reducing the roughness from 2 to 0.6 and then to 0.2 μm proportionally decreased the amount of deposit, and the diamond-like-carbon, CrN, and NiCr–CrC composite coatings effectively hindered the fouling process. This study provides fundamental insights into the MSW fouling and proof-of-concept of potential mitigations through the screw surface modification.

09 BIOMASS FUELS↗
DOE OSTI2024

Evaluation of a New Approach for Entrainment and Detrainment Rate Estimation

Entrainment and detrainment rates (ε and δ) constitute the most critical free parameters in mass flux schemes commonly employed for cumulus parameterizations. Recently, Zhu et al. (2021) introduced a new approach that utilizes aircraft observations to simultaneously estimate ε and δ for cumulus clouds, overcoming the limitation of other observation-based approaches that solely yield ε without offering insights into δ. This study aims to comprehensively evaluate the reliability of this new approach. First, evaluation using an Explicit Mixing Parcel Model demonstrates the capability of the new approach to back-calculate predetermined ε and δ based on the physical properties before and after the entrainment mixing. Second, evaluation using large-eddy simulations illustrates that the new approach yields consistent ε and δ profiles compared to the traditional approach. Sensitivity tests indicate a weak sensitivity of the estimated δ with the new approach to the entrained air source. A decrease in the proportion of cloudy air in the assumed detrained air leads to a reduction in the estimated δ, while ε remains unaffected. Finally, the most appropriate assumptions for entrained and detrained air are discussed. Estimating ε for cumulus parameterizations involves acquiring ambient air more than 500 m away from the cloud edge as entrained air. Due to implicit mean field approximations in the traditional approach, determining the optimal assumption for detrained air properties proves challenging. Finally, this study confirms the reliability of the new approach in estimating ε and δ, providing confidence in its application to extensive observational data and advancement in parameterization.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2024

Predicting Instability and the Effect of Wind Loading on Single-Axis Trackers

As PV modules continue to trend toward larger, thinner, and more flexible forms they grow more susceptible to damage from dynamic wind loading. As a result, understanding the impact of wind on PV systems, particularly when mounted on solar-tracking hardware, and identifying robust, stable array layouts and stow strategies is becoming increasingly important for the PV community. In our ongoing DuraMAT project, we are developing an open-source software package, PVade (PV aerodynamic design engineering), to simulate the cascading fluid-structure interaction that occurs within solar-tracking arrays to enable researchers to test hardware, layout, and tracker control changes, leading to enhanced stability and a reduction in wind-driven damage. We will give an overview of the PVade software, highlighting recent user-interface and algorithm developments, before presenting the latest outcomes from our ongoing validation campaign in which we analyze and compare with experimental data obtained from a DuraMAT 1 project. From there, we will present simulated results from a larger, multi-row array and highlight relationships between varying tracker angles and stability as measured by different experimentally validated metrics.

fluid structure interaction↗
DOE OSTI2024

Minimizing Toxicity and Optimizing Lubricity of Ionic Liquids for Eco-Friendly Lubrication

As much as 60 million liters of lubricating fluids end up in the environment annually, and thus, the environmental impact of lubricants is increasingly recognized in addition to meeting the rheological and tribological requirements. Although US Environmental Protection Agency-approved environmentally acceptable base fluids are available, there is a lack of additives that are both nontoxic and effective in wear protection. Here, this study reports the successful development of a new class of ionic liquids (ILs) with demonstrated significantly lower aquatic toxicity and superior friction reduction and wear protection capabilities compared with a commercial lubricant additive and some ILs reported in the literature. Specifically, ammonium phosphate and phosphonium phosphate ILs with four-carbon alkyls have been identified with balanced oil solubility, thermal stability, toxicity, and lubricity, which provide fundamental insights for future development of eco-friendly ILs.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Assessing the cost-effectiveness of carbon neutrality for light-duty vehicle sector in China

China’s progress in decarbonizing its transportation, particularly vehicle electrification, is notable. However, the economically effective pathways are underexplored. To find out how much cost is necessary for carbon neutrality for the light-duty vehicle (LDV) sector, this study examines twenty decarbonization pathways, combining the New Energy and Oil Consumption Credit model and the China-Fleet model. We find that the 2060 zero-greenhouse gas (GHG) emission goal for LDVs is achievable via electrification if the battery pack cost is under CNY483/kWh by 2050. However, an extra of CNY8.86 trillion internal subsidies is needed under pessimistic battery cost scenarios (CNY759/kWh in 2050) to eliminate 246 million tonnes of CO 2 -eq by 2050 ensuring over 80% market penetration of battery electric vehicles (BEVs) in 2050. Moreover, the promotion of fuel cell electric vehicles is synergy with BEVs to mitigate the carbon abatement difficulties, decreasing up to 34% of the maximum marginal abatement internal investment.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2023

Ionic liquids containing quaternary ammonium and phosphonium cations, and their use as environmentally friendly lubricant additives

An ionic liquid composition having the following generic structural formula: wherein Z is N or P, and R 1 , R 2 , R 3 , and R 4 are independently selected from hydrogen atom and hydrocarbon groups having one to four carbon atoms with optional interconnection to form a cyclic group that includes Z, and wherein R 1 , R 2 , R 3 , and R 4 are all hydrocarbon groups when Z is P, and X− is a phosphorus-containing or carboxylate anion, particularly an organophosphate, organophosphonate, or organophosphinate anion, or a thio-substituted analog thereof containing hydrocarbon groups with at least three carbon atoms. Also described are lubricant compositions comprising the above ionic liquid and a base lubricant, wherein the ionic liquid is dissolved in the base lubricant. Further described are methods for applying the ionic liquid or lubricant composition onto a mechanical device for which lubrication is beneficial, with resulting improvement in friction reduction, wear rate, and/or corrosion inhibition.

Qu, Jun↗
DOE OSTI2023

Tracking Flows of End-of-Life Battery Materials and Manufacturing Scrap

This paper defines terms such as “recycling rate” that enable the characterization of flows of battery materials and expands the terminology to accommodate the description of complex product recycling. It also estimates the maximum percentage of U.S. demand for critical elements that could be satisfied by recycling as demand continues to grow, and it defines and estimates the recycling rate for lithium-ion batteries. Finally, it clarifies the role of manufacturing scrap as the domestic U.S. supply chain is built up. It concludes that recycling will be important in the long term, but growth still requires that new material be extracted to supply additional material.

25 ENERGY STORAGE↗
DOE OSTI2023

Observational study of relationships between entrainment rate, homogeneity of mixing, and cloud droplet relative dispersion

The entrainment–mixing process is key to the cloud’s dynamical and microphysical processes. However, to the best of our knowledge, no study has quantitatively linked entrainment rate and homogeneity of mixing. Additionally, their combined effects on cloud droplet relative dispersion and physical mechanisms are even more unclear. This study analyzed the aircraft measurements of cumulus clouds collected in the Holistic Interactions of Shallow Clouds, Aerosols, and Land-Ecosystems field campaign to identify these relationships. The relationship between the entrainment rate and homogeneous mixing degree was found to be moderately positive, and the underlying mechanisms related to mixing and evaporation time scales and environmental relative humidity were explored. The relationship between relative dispersion and entrainment rate changes from positive to negative with increasing entrainment rate, depending on the dominance of evaporation of large or small droplets. The relative dispersion first increases and then decreases with increasing homogeneous mixing degree, validating the results of previous model simulations. Further, the results shed new light on understanding the interactions between cloud microphysics and cloud dynamics through turbulent entrainment and mixing processes.

54 ENVIRONMENTAL SCIENCES↗