Ex situ bismuth doping for efficient CdSeTe thin-film solar cells with open-circuit voltages exceeding 900 mV
We dope CdTe solar cells with Bi after the device structure is completed using a solution process.
CdTe solar cell↗
Engineering topics
Heben, Michael J.
Publications and source records attributed to Heben, Michael J..
Enhanced understanding of recombination mechanisms in high-performance tin-lead perovskite solar cells
Not Available
Abudulimu, Abasi (ORCID:0000000217940993)↗
Evaporated CdSe for Efficient Polycrystalline CdSeTe Thin-Film Solar Cells
Recent progress has shown that alloying cadmium telluride (CdTe) with cadmium selenide (CdSe) to create a CdSexTe1-x (CdSeTe) gradient region can significantly boost the performance of polycrystalline CdSeTe thin-film solar cells. However, improper CdSeTe alloying might introduce problematic band alignment and deleterious voids at the front interface, limiting the benefit maximization of this technique. Here, we show that the CdSe layers deposited by thermal evaporation result in CdSeTe cells with a higher performance than the sputtered CdSe. This is because evaporated CdSe can avoid the formation of voids at the front interface, producing improved front junction quality with suppressed front junction nonradiative recombination. The champion cell using evaporated CdSe demonstrated a power conversion efficiency (PCE) of 19.7%, much higher than 18.1% in the cell using sputtered CdSe.
cadmium selenide↗
Suppressed deprotonation enables a durable buried interface in tin-lead perovskite for all-perovskite tandem solar cells
Low-band-gap tin (Sn)-lead (Pb) perovskites are a critical component in all-perovskite tandem solar cells (APTSCs). Current state-of-the-art Sn-Pb perovskite devices exclusively use poly(3,4-ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) as the hole-transport layer (HTL) but suffer from undesired buried-interface degradation. Here, we show that the deprotonation of the –SO 3 H group in PSS is the root cause of the interface degradation due to its low acid dissociation constant (pK a ), leading to acidic erosion and iodine volatilization in Sn-Pb perovskites. We identify that HTL featuring the carboxyl (–COOH) group with a higher pK a , such as poly[3-(4-carboxybutyl)thiophene-2,5-diyl] (P3CT), can suppress deprotonation and strengthen the interface, mitigating the buried-interface degradation. Motivated by established P3CT modification, we introduce Pb doping to P3CT to increase its work function and reduce interfacial energy loss. Furthermore, we fabricate APTSCs with a champion efficiency of 27.8% and an operational lifetime of over 1,000 h, with 97% retaining efficiency under maximum power point tracking.
08 HYDROGEN↗
Four–Terminal Perovskite–CdSeTe Tandem Solar Cells: From 25% toward 30% Power Conversion Efficiency and Beyond
Thin-film tandem photovoltaic (PV) technology has emerged as a promising avenue to enhance power conversion efficiency beyond the radiative efficiency limit of single-junction devices. Combining a tunable wide-bandgap perovskite cell with a commercially established narrow-bandgap cadmium selenium telluride (CdSeTe) cell in a comparatively easy-to-fabricate four-terminal (4-T) arrangement is a great step in that direction. Herein, the impact of the transparent back contact and the perovskite absorber bandgap on the performance of 4-T perovskite–CdSeTe tandem solar cells is investigated. 4-T perovskite–CdSeTe tandem device architecture with ≈25% efficiency is demonstrated and a feasible pathway is shown to improve the tandem efficiency to more than 30%. Furthermore, the results show that the integration of CdSeTe with perovskite in 4-T tandem PV configurations represents a significant advancement toward achieving higher efficiency and low-cost tandem PVs.
14 SOLAR ENERGY↗
Comprehensive Study of Carrier Recombination in High‐Efficiency CdTe Solar Cells Using Transient Photovoltage
Cadmium telluride (CdTe) solar cells represent a commercially successful photovoltaic technology, with an annual production capacity approaching 20 GW. However, improving the open-circuit voltage (V OC ) remains challenging. This study aims to deepen the understanding of charge carrier recombination in CdTe solar cells and to explore alternative dynamical characterization methods that address the limitations found in conventionally used time-resolved photoluminescence for CdTe solar cells. Transient photovoltage and transient photocurrent techniques are utilized to investigate charge carrier dynamics under conditions resembling real-world solar cell operation. The results reveal that an effective nonradiative recombination lifetime of 580 ns dominates the charge dynamics at VOC values below 850 mV. Above this threshold, radiative recombination becomes significant, with a radiative recombination coefficient of 1.1 × 10 −9 cm 3 s −1 . Additionally, the stationary charge carrier density at 1 sun is determined to be around 1 × 10 14 cm −3 . By accurately determining both radiative and nonradiative recombination, this work provides a comprehensive understanding of carrier dynamics in high-performing CdTe devices and paves the way for improving the V OC and performance of CdTe solar cells.
CdTe solar cells↗
The effect of remnant CdSe layers on the performance of CdSeTe/CdTe photovoltaic devices
Thin film CdTe-based photovoltaic devices have achieved high efficiency above 22 %. The recent improvement in efficiency is due to Se alloying in the CdTe absorbers to form a CdSeTe/CdTe structure. The subsequent band gap grading increases the short circuit current density. The Se can be introduced by depositing a precursor thin film of either CdSe or a CdSeTe alloy and then diffusing the Se into the CdTe during the high temperature cadmium chloride activation process. Using CdSe is preferred because it is easier to control the Se concentration. However, during fabrication of the CdSeTe/CdTe devices, the CdSe thickness needs to be precisely controlled to prevent the retention of a CdSe remnant layer after the activation treatment. Retention of a remnant CdSe layer causes a dramatic reduction in device efficiency. In this work, we show that the reduction in efficiency is caused by a number of factors. The remnant CdSe layer is n-type which moves the position of the p-n junction. Also, it is widely thought that the CdSe remnants are photo-inactive. In this work, we clarify that the individual CdSe grains are actually highly photo-active. However, the grain sizes in the CdSe remnant and the adjacent CdSeTe layer are very small resulting in a high grain boundary area. Although the grain boundaries are passivated with chlorine, cathodoluminescence imaging and electrical measurements show that this is only partially effective. Also, EQE measurements show that the remnant CdSe causes parasitic absorption. Overall, the remnant CdSe layer causes a reduction in short circuit current density and device efficiency. The thickness of the CdSe precursor layer and the cadmium chloride activation process conditions must be precisely optimised to ensure that all the CdSe is consumed and inter-diffused to form the CdSeTe alloy for highest efficiency devices.
CdSe remnant↗
Approach to determining the limiting recombination mechanism in CdTe-based solar cells
Not Available
Energy & Fuels↗
Cadmium Telluride Accelerator Consortium (CTAC)
The United States is the leader in cadmium telluride (CdTe) photovoltaic (PV) manufacturing, and CdTe is the second most-deployed solar technology in the world. The CdTe Accelerator Consortium (CTAC) was formed to enhance U.S. technology leadership and competitiveness in CdTe photovoltaics (PV) including increasing cell efficiencies, decreasing module costs, and maintaining or increasing domestic CdTe PV material and module production. Leadership for the 3-year consortium was selected by an NREL team through a competitive solicitation. CTAC was formally announced on August 1st by U.S. Secretary of Energy Jennifer M. Granholm and U.S. Representative Marcy Kaptur at an event held at University of Toledo. We will give an overview of CTAC research directions along with their goals and activities. We can also discuss how CTAC relates to the National Renewable Energy Laboratory (NREL) and to the U.S. Manufacturing of Advanced Cadmium Telluride Photovoltaics Consortium (US-MAC). Visit our poster to find out who leads CTAC and how you can get involved.
costs↗
Seed‐Assisted Growth for Scalable and Efficient Perovskite Solar Modules
Perovskite solar modules (PSMs) have shown remarkable photovoltaic potentials, but they still suffer from large power conversion efficiency (PCE) loss on scale‐up and instability due to inferior uniformity and crystallization over large areas. Herein, the scalable production of efficient and stable PSMs using a suite of all‐scalable fabrication methods featuring a two‐step blade/dip‐coating approach to deposit the perovskite absorber layer is demonstrated. Rubidium chloride is introduced to embed (PbI 2 ) 2 RbCl complex seeds in the first‐deposited PbI 2 precursor, which assists in uniform crystallization of the perovskite layer with high crystallinity and reduced defect density over large areas. Following the optimization of RbCl additives, a champion PSM with 17.9% PCE on a 7.6 × 7.6 cm 2 substrate with a 37 cm 2 aperture area is achieved. Moreover, the RbCl‐incorporated PSMs demonstrate excellent reproducibility and stability under continuous 1 sun illumination. This work shows that the two‐step blade/dip coating is a promising method for producing high‐efficiency and stable PSMs on an industrially relevant scale.
Energy & Fuels↗
Understanding and Advancing Bifacial Thin Film Solar Cells under Dual Illumination
There is a great deal of interest in increasing the energy yield from thin film solar cells by implementing bifacial operation. However, deleterious band bending and high interface recombination at the back transparent electrode can cause problems. Herein, it is investigated how bifacial thin film devices perform when illuminated through the front, back, and simultaneously through both interfaces using numerical modeling. It is shown that the downward band bending near the back interface is reduced during illumination when the carrier concentration is low. This effect is not found when the doping is relatively high, but the minority carrier distribution is still modified. Under either condition, the power generated under bifacial illumination exceeds the sum of the power generated when the illumination is solely from the back or the front. It is also shown that the back-illuminated device performance is independent of the angle at which the light enters the back of the device, which provides accommodation for scattered light. Finally, the power enhancement is calculated for bifacial devices relative to front-illuminated devices, and is shown that any significant loss in frontside power generation is difficult to overcome with back illumination under real-world albedo conditions.
CdTe↗
Incorporating Potassium Citrate to Improve the Performance of Tin‐Lead Perovskite Solar Cells
Abstract Easy‐to‐form tin vacancies at the buried interface of tin‐lead perovskites hinder the performance of low‐bandgap perovskite solar cells (PSCs). Here, a synergistic strategy by incorporating potassium citrate (PC) into the poly(3,4‐ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) hole‐transport layer to passivate the buried interface of Sn‐Pb PSCs is reported. PC neutralizes the acidity of PEDOT:PSS and stabilizes the perovskite front surface, enhancing device stability. Citrate moieties coordinate with Sn 2+ on the buried perovskite surface, preventing Sn 2+ oxidation and suppressing defect formation. Additionally, potassium cations incorporate into Sn‐Pb perovskites, enhancing crystallinity and passivating halide defects. The combined benefits enable efficient low‐bandgap Sn‐Pb PSCs with a power conversion efficiency of 22.7% and a high open‐circuit voltage of 0.894 V. Using this method, 26.1% efficiency for all‐perovskite tandem solar cells is demonstrated. These results emphasize the significance of buried interface passivation in developing efficient and stable Sn‐Pb PSCs and all‐perovskite tandem solar cells.
14 SOLAR ENERGY↗
Brief: Daily Performance Changes in Metal Halide Perovskite PV Modules
Metal halide perovskite photovoltaic modules deployed outdoors and held at their maximum power point show daily, reversible, relative changes of up to 30% in efficiency between morning and afternoon. Predicting energy yield and quantifying reliability will require properly handling such daily performance changes.
14 SOLAR ENERGY↗
Engineering Perovskite Precursor Inks for Scalable Production of High‐Efficiency Perovskite Photovoltaic Modules
Abstract Blade coating of perovskite solar cells (PSCs) and modules has progressed considerably toward the industrial production of perovskite photovoltaics. Developing stable perovskite precursors is critical for achieving uniform coating over large areas. Here, the engineering of a perovskite precursor solution consisting of 2‐methoxyethanol (2‐Me) and 1,3‐dimethyl‐imidazolidinone (DMI) with superior intermediate phase stability that enables scalable production of efficient perovskite solar modules is reported. With this perovskite precursor solution, uniform and pinhole‐less perovskite film is deposited over a large area of > 100 cm 2 and higher‐efficiency PSCs and modules are obtained. The best‐performing unit cell and module with n‐i‐p configuration reach power conversion efficiencies of 23.4% and 20.1%, respectively. Additionally, a series of non‐destructive metrology methods, such as spectroscopic ellipsometry, hyperspectral photoluminescence, electroluminescence, and laser beam‐induced current mapping, are employed to assess and guide the development the blade‐coated perovskite modules. This results show that rational engineering of precursor inks for blade coating is promising for the scalable production of efficient perovskite solar modules.
36 MATERIALS SCIENCE↗
CdTe-based thin film photovoltaics: Recent advances, current challenges and future prospects
Cadmium telluride (CdTe)-based cells have emerged as the leading commercialized thin film photovoltaic technology and has intrinsically better temperature coefficients, energy yield, and degradation rates than Si technologies. More than 30 GW peak (GWp) of CdTe-based modules are installed worldwide, multiple companies are in production, modules are shipping at up to 18.6% efficiency, and lab cell efficiency is above 22%. We review developments in the science and technology that have occurred over approximately the past decade. These achievements were enabled by manufacturing innovations and scaling module production, as well as maximizing photocurrent through window layer optimization and alloyed CdSe x Te 1-x (CST) absorbers. Improved chlorine passivation processes, film microstructure, and serendipitous Se defect passivation significantly increased minority carrier lifetime. Efficiencies >22% have been realized for both Cu and As doped CST-based cells. The path to further efficiency gains hinges primarily on increasing open circuit voltage (V oc ) and fill factor (FF) through innovations in materials, fabrication methods, and device stacks. Replacing the longstanding Cu doping with As doping is resulting in better module stability and is being translated to large-scale production. To realize 25% efficiency and >1 V V oc , research and development is needed to increase the minority carrier lifetime beyond 100 ns, reduce grain boundary and interface recombination, and tailor band diagrams at the front and back interfaces. Many of these goals have been realized separately however combining them together using scalable manufacturing approaches has been elusive to date. We review these achievements and outstanding opportunities for this remarkable photovoltaic technology.
14 SOLAR ENERGY↗
Oxygen Management to Avoid Photo-Inactive Cd(S,Se) for Efficient Cd(Se,Te) Solar Cells
Our previous work has demonstrated that the formation of a penternary cadmium chalcogenide Cd(O,S,Se,Te) region can significantly reduce the front interface recombination in Cd(Se,Te)-based thin-film solar cells. In this work, we have shown that oxygen management during the device fabrication is crucial to form this region. While both the CdS and CdSe layer depositions and the postdeposition CdCl2 treatment should be conducted in the presence of oxygen, the CdTe deposition should be conducted in an oxygen-free atmosphere. Improper oxygen management leads to low device performance due to the formation of a photoinactive Cd(S,Se) region and reduced absorber quality. Additionally, we investigated the carrier transport and collection properties in devices with photoinactive Cd(S,Se) and photoactive Cd(O,S,Se,Te) at the front interface to gain comprehensive understanding of the mechanisms that resulted in improved efficiencies approaching 20%.
CdTe deposition↗
Water-Assisted Lift-Off Process for Flexible CdTe Solar Cells
In recent years, various lift-off methods have been developed to fabricate lightweight and flexible cadmium telluride (CdTe)-based solar cells. In this work, we report flexible cadmium sulfide (CdS)/CdTe solar cells using a water-assisted lift-off approach. Here we demonstrate that an additional cadmium chloride treatment for the CdS film is critical to improve the grain size of CdS and the post-deposited CdTe film and the electron conductivity of the CdS film. As a result, the quality of the CdS/CdTe front junction is significantly improved with reduced nonradiative recombination. Finally, our lightweight and flexible polycrystalline CdTe solar cells demonstrate a champion power conversion efficiency of 12.6%.
14 SOLAR ENERGY↗
Control-Centric Living Laboratory for Management of Distributed Energy Resources
Not Available
Kini, Roshan L.↗