Search NASA⌕ Search

Engineering topics

Hedgepeth, J. M.

Publications and source records attributed to Hedgepeth, J. M..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Mission to Planet Earth technology assessment and development for large deployable antennas

A NASA R&D program, the Large Deployable Antenna program, was initiated to investigate and demonstrate the availability of critical technologies for passive microwave imagers. The science objectives, current state-of-the-art, a number of electromagnetic configurations under consideration, and the mechanical systems development effort are presented. The program team conducted a detailed technology review, evaluated the feasibility and technology readiness for a large dual-reflector radiometer, and developed a system concept for a 25-meter deployable radiometer. The study approach involved determining basic operational parameters and configurations for a geosynchronous wide-scanning radiometer from which specific structural requirements were utilized as goals (rather than specifications) with which specific technologies could be evaluated.

Rogers, C. A.↗
NASA NTRS1989

Structures for remotely deployable precision antennas

Future space missions such as the Earth Science Geostationary Platform (ESGP) will require highly accurate antennas with apertures that cannot be launched fully formed. The operational orbits are often inaccessible to manned flight and will involve expendable launch vehicles such as the Delta or Titan. There is therefore a need for completely deployable antenna reflectors of large size capable of efficiently handling millimeter wave electromagnetic radiation. The parameters for the type of mission are illustrated. The logarithmic plot of frequency versus aperture diameter shows the regions of interest for a large variety of space antenna applications, ranging from a 1500-meter-diameter radio telescope for low frequencies to a 20-meter-diameter infrared telescope. For the ESGP, a major application is the microwave radiometry at high frequencies for atmospheric sounding. Almost all existing large antenna reflectors for space employ a mesh-type reflecting surface. Examples are shown and discussed which deal with the various structural concepts for mesh antennas. Fortunately, those concepts are appropriate for creating the very large apertures required at the lower frequencies for good resolution. The emphasis is on the structural concepts and technologies that are appropriate to fully automated deployment of dish-type antennas with solid reflector surfaces. First the structural requirements are discussed. Existing concepts for fully deployable antennas are then described and assessed relative to the requirements. Finally, several analyses are presented that evaluate the effects of beam steering and segmented reflector design on the accuracy of the antenna.

Hedgepeth, J. M.↗
NASA NTRS1986

Structural concepts for large solar concentrators

Solar collectors for space use are examined, including both early designs and current concepts. In particular, attention is given to stiff sandwich panels and aluminum dishes as well as inflated and umbrella-type membrane configurations. The Sunflower concentrator is described as an example of a high-efficiency collector. It is concluded that stiff reflector panels are most likely to provide the long-term consistent accuracy necessary for low-orbit operation. A new configuration consisting of a Pactruss backup structure, with identical panels installed after deployment in space, is presented. It is estimated that concentration ratios in excess of 2000 can be achieved with this concept.

Hedgepeth, J. M.↗
NASA NTRS1986

Synchronously Deployable Truss Structures

Structure lightweight, readily deployed, and has reliable joints. New truss concept, designated as "pac truss," developed. Features easy deployment without need for complex mechanisms. Structures of this type deployed in free flight by controlled release of stored energy in torsional springs at selected hinges located throughout structure. Double-folding technique used in beam model applicable to flat planar trusses, allowing structures of large expanse to fold into compact packages and be deployed for space-platform applications.

Rhodes, M. D.↗
NASA NTRS1985

Inflatable Column Structure

Lightweight structural member easy to store. Billowing between circumferential loops of fiber inflated column becomes series of cells. Each fiber subjected to same tension along entire length (though tension is different in different fibers). Member is called "isotensoid" column. Serves as jack for automobiles or structures during repairs. Also used as support for temporary bleachers or swimming pools.

Hedgepeth, J. M.↗
NASA NTRS1985

Precision antenna reflector structures

The assembly of the Large Precise Reflector Infrared Telescope is detailed. Also given are the specifications for the Aft Cargo Carrier and the Large Precision Reflector structure. Packaging concepts and options, stowage depth and support truss geometry are also considered. An example of a construction scenario is given.

Hedgepeth, J. M.↗
NASA NTRS1985

Finite element analysis of partly wrinkled membranes

The development of a nonlinear numerical algorithm for the analysis of stresses and displacements in partly wrinkled flat membranes, and its implementation on the SAP VII finite-element code are described. A comparison of numerical results with exact solutions of two benchmark problems reveals excellent agreement, with good convergence of the required iterative procedure. An exact solution of a problem involving axisymmetric deformations of a partly wrinkled shallow curved membrane is also reported.

Miller, R. K.↗
NASA NTRS1984

Support structures for large infrared telescopes

An infrared telescope requires an accuracy of its reflecting surfaces of less than a micrometer. Future missions may require such accuracy from telescopes that are 20 meters or larger in diameter. The structure for supporting such a telescope will most probably take the form of a deep truss. Various approaches for constructing the primary mirror in space are illustrated. One that employs automated deployment of interconnected reflector-structure modules was described in detail. Estimates were made of the precision obtainable with properly configured truss structures and the required ability of active control systems for achieving the desired accuracy.

Hedgepeth, J. M.↗
NASA NTRS1984

A study of structural concepts for ultralightweight spacecraft

Structural concepts for ultralightweight spacecraft were studied. Concepts for ultralightweight space structures were identified and the validity of heir potential application in advanced spacecraft was assessed. The following topics were investigated: (1) membrane wrinkling under pretensioning; (2) load-carrying capability of pressurized tubes; (3) equilibrium of a precompressed rim; (4) design of an inflated reflector spacecraft; (5) general instability of a rim; and (6) structural analysis of a pressurized isotensoid column. The design approaches for a paraboloidal reflector spacecraft included a spin-stiffened design, both inflated and truss central columns, and to include both deep truss and rim-stiffened geodesic designs. The spinning spacecraft analysis is included, and the two truss designs are covered. The performances of four different approaches to the structural design of a paraboloidal reflector spacecraft are compared. The spinning and inflated configurations result in very low total masses and some concerns about their performance due to unresolved questions about dynamic stability and lifetimes, respectively.

Miller, R. K.↗
NASA NTRS1984

Finite element analysis of wrinkling membranes

The development of a nonlinear numerical algorithm for the analysis of stresses and displacements in partly wrinkled flat membranes, and its implementation on the SAP VII finite-element code are described. A comparison of numerical results with exact solutions of two benchmark problems reveals excellent agreement, with good convergence of the required iterative procedure. An exact solution of a problem involving axisymmetric deformations of a partly wrinkled shallow curved membrane is also reported.

Miller, R. K.↗
NASA NTRS1983

Structures for large precision reflectors

The design and fabrication of a highly accurate large aperture infrared reflecting telescope is discussed. The structural concept is an off axis Cassegrainian design with a focal length equal to the aperture diameter. Thermal shielding, peak heat fluxes, cooling rates, active control tasks, and deployment sequence are discussed.

Hedgepeth, J. M.↗
NASA NTRS1983

Design concepts for large reflector antenna structures

Practical approaches for establishing large, precise antenna reflectors in space are described. Reflector surfaces consisting of either solid panels or knitted mesh are considered. The approach using a deep articulated truss structure to support a mesh reflector is selected for detailed investigations. A new sequential deployment concept for the tetrahedral truss is explained. Good joint design is discussed, and examples are described both analytically and by means of demonstration models. The influence of curvature on the design and its vibration characteristics are investigated.

Hedgepeth, J. M.↗
NASA NTRS1982

An algorithm for finite element analysis of partly wrinkled membranes

A generalization and numerical implementation is presented of the Stein-Hedgepeth (1961) continuum theory for the analysis of partly wrinkled membranes, such as the tensioned membrane surfaces which are found in spacecraft structural components. The approach has its basis in experimental observations showing that when wrinkles develop in a membrane parallel to the x direction, the associated overall contraction in the y direction exceeds that predicted by the Poisson's ratio effect.

Miller, R. K.↗
NASA NTRS1982

Accuracy potentials for large space antenna reflectors with passive structure

Analytical results indicate that a careful selection of materials and truss design, combined with accurate manufacturing techniques, can result in very accurate surfaces for large space antennas. The purpose of this paper is to examine these relationships for various types of structural configurations. Comparisons are made of the accuracy achievable by truss- and dome-type structures for a wide range of diameter and focal length of the antenna and wavelength of the radiated signal.

Hedgepeth, J. M.↗
NASA NTRS1982

Influence of fabrication tolerances on the surface accuracy of large antenna structures

One of the sources of error in radio frequency antennas is the lack of dimensional precision of the surface. This paper presents an approach for estimating the amount of error caused by random dimensional imperfections of the many structural elements which make up a truss-type antenna. A principle of equivalence between the analyses of statistical errors and of the natural vibration frequencies of the structure is developed. Examples are presented to show the application of this equivalence principle to the determination of average surface errors of several types and proportions of antenna structures.

Hedgepeth, J. M.↗
NASA NTRS1982

Finite element analysis of wrinkling membranes

The finite element analysis of wrinkling membranes was investigated. The determination of stresses and deformations within large partly wrinkled membrane surfaces is a problem of significant technical interest in such areas as conceptual design and analysis of ultra lightweight spacecraft structures. A closed-form solution to an axisymmetric problem involving partial wrinkling of an inflated shallow membrane was obtained. In particular, a membrane in the shape of a sperical annulus was considered. The outer edge of the annulus was assumed to be fixed so that no displacements occur along the outer perimeter. The inner edge is assumed to be clamped to a rigid movable plug. Solutions for the complete stress, strain, and displacement fields under the assumption of inextensional material behavior are presented for the case of pure torsional loads applied to the plug, and for the case of pure axial loads applied to the plug.

Miller, R. K.↗
NASA NTRS1981

Efficient structures for geosynchronous spacecraft solar arrays. Phase 1, 2 and 3

Structural concepts for deploying and supporting lightweight solar-array blankets for geosynchronous electrical power are evaluated. It is recommended that the STACBEAM solar-array system should be the object of further study and detailed evaluation. The STACBEAM system provides high stiffness at low mass, and with the use of a low mass deployment mechanism, full structural properties can be maintained throughout deployment. The stowed volume of the STACBEAM is acceptably small, and its linear deployment characteristic allows periodic attachments to the solar-array blanket to be established in the stowed configuration and maintained during deployment.

Adams, L. R.↗