Engineering topics

Hegde, Uday

Publications and source records attributed to Hegde, Uday.

14 records

NASA NTRS2019

Two-Stage Autoignition Dynamics of N-Dodecane Droplets Under Normal Gravity at High Pressures

Experimental observations of two-stage, autoignition characteristics of fiber-supported, n-dodecane fuel droplets under normal gravity are reported for a wide range of ambient temperatures, and pressures varying from 1 atm to 25 atm, which encompasses the fuel critical pressure (~ 18 atm). A high-speed camera is used to obtain backlit images of the autoignition process. During two-stage ignition, a cool-flame front forms below the droplet in the natural convective plume of the fuel vapor originating from the vaporizing droplet, and propagates upward, followed by the formation of a hot-flame kernel that expands rapidly and surrounds the droplet, eventually leading to the classical diffusion flame. Experimentally measured cool, and hot flame formation locations and propagation speeds are presented for varying initial temperatures and pressures. Measured first, and second stage ignition delay times are also reported. The influences of negative temperature coefficient (NTC) regime chemistry on flame starting location, propagation speeds, and ignition delay times are described. The first-stage cool flame characteristics are found to be controlled by both the chemistry, and physical aspects such as droplet evaporation and fuel-oxidizer mixing, while the second-stage hot flame ignition is primarily controlled by chemical kinetics. Further work is currently underway to develop models to quantitatively predict the observed behavior.

Rose, Evan↗

NASA NTRS2017

Behavior of a Salt Water Solution Near the Critical Point Under Microgravity Conditions

The Supercritical Water Mixture (SCWM) experiment conducted on the International Space Station (ISS) is designed to study a salt-water solution in the vicinity of the critical transition with a test cell filled with Na2SO4 (aq) 0.5-w. This salt is a Type II salt which undergoes a dramatic decrease in solubility past waters critical point. The paper discusses the liquid-vapor-salt distribution in the test cell for subcritical, trans-critical, and supercritical regimes. In 0-g, the vapor-liquid interface manifests itself by the presence of a large single vapor bubble that is flattened between the two windows. In contrast with pure water, the vapor bubble remains centered in the test cell and is stable for temperatures up to Tc - 50 mK. The processes leading to critical transition during heat-up, as marked by the break-up of the vapor bubble, depends on the applied heating rate. For temperature ramps 1 mKmin, the bubble interface begins to breakup with the formation of a large number of smaller bubbles. For larger temperature ramps (10mKmin), temperature gradients arise in the cell pushing the bubble toward a window surface. As the critical threshold is crossed small variations in cell temperature ( 1 mK) cause an observable spatial variation in density. However, this spatial variation is not discernible as the temperature is increased further into the supercritical regime. The salt precipitation in the vicinity of the critical crossing appears to be heterogeneous in nature with precipitates observable on the cell windows. Direct imaging as well as light scattering indicate a hexagonal structure of the precipitated salt crystals in the near critical regime. The salt deposition is not fully reversible as the temperature is reduced due to window corrosion effects which traps some of the precipitated salt. Critical temperatures as high as 1.9 K above the value for pure water (647.25 K) have been measured. Finally, results on the critical transition phenomena in the presence of an imposed temperature gradient, demonstrating the remarkable stability of the central bubble, are also presented.

near-critical↗

NASA NTRS2013

Effects of Gravity on Supercritical Water Oxidation (SCWO) Processes

The effects of gravity on the fluid mechanics of supercritical water jets are being studied at NASA to develop a better understanding of flow behaviors for purposes of advancing supercritical water oxidation (SCWO) technologies for applications in reduced gravity environments. These studies provide guidance for the development of future SCWO experiments in new experimental platforms that will extend the current operational range of the DECLIC (Device for the Study of Critical Liquids and Crystallization) Facility on board the International Space Station (ISS). The hydrodynamics of supercritical fluid jets is one of the basic unit processes of a SCWO reactor. These hydrodynamics are often complicated by significant changes in the thermo-physical properties that govern flow behavior (e.g., viscosity, thermal conductivity, specific heat, compressibility, etc), particularly when fluids transition from sub-critical to supercritical conditions. Experiments were conducted in a 150 ml reactor cell under constant pressure with water injections at various flow rates. Flow configurations included supercritical jets injected into either sub-critical or supercritical water. Profound gravitational influences were observed, particularly in the transition to turbulence, for the flow conditions under study. These results will be presented and the parameters of the flow that control jet behavior will be examined and discussed.

aqueous solutions↗

NASA NTRS2012

Evaluation of Heat Recuperation in a Concentric Hydrogen Reduction Reactor

Heat recuperation in an ISRU reactor system involves the recovery of heat from a reacted regolith batch by transferring this energy into a batch of fresh regolith. One concept for a hydrogen reduction reactor is a concentric chamber design where heat is transferred from the inner, reaction chamber into fresh regolith in the outer, recuperation chamber. This concept was tested and analyzed to define the overall benefit compared to a more traditional single chamber batch reactor. Data was gathered for heat-up and recuperation in the inner chamber alone, simulating a single chamber design, as well as recuperation into the outer chamber, simulating a dual chamber design. Experimental data was also used to improve two analytical models, with good agreement for temperature behavior during recuperation, calculated mass of the reactor concepts, and energy required during heat-up. The five tests, performed using JSC-1A regolith simulant, also explored the effectiveness of helium gas fluidization, hydrogen gas fluidization, and vibrational fluidization. Results indicate that higher hydrogen volumetric flow rates are required compared to helium for complete fluidization and mixing, and that vibrational fluidization may provide equivalent mixing while eliminating the need to flow large amounts of excess hydrogen. Analysis of the total energy required for heat-up and steady-state operations for a variety of conditions and assumptions shows that the dual-chamber concept requires the same or more energy than the single chamber concept. With no clear energy savings, the added mass and complexity of the dual-chamber makes it unlikely that this design concept will provide any added benefit to the overall ISRU oxygen production system.

Linne, Diane↗

NASA NTRS2006

Modeling of Heat and Mass Transfer in a TEC-Driven Lyophilizer

Dewatering of wet waste during space exploration missions is important for crew safety as it stabilizes the waste. It may also be used to recover water and serve as a preconditioning step for waste compaction. A thermoelectric cooler (TEC)-driven lyophilizer is under development at NASA Ames Research Center for this purpose. It has three major components: (i) an evaporator section where water vapor sublimes from the frozen waste, (ii) a condenser section where this water vapor deposits as ice, and (iii) a TEC section which serves as a heat pump to transfer heat from the condenser to the evaporator. This paper analyses the heat and mass transfer processes in the lyophilizer in an effort to understand the ice formation behavior in the condenser. The analysis is supported by experimental observations of ice formation patterns in two different condenser units.

Yuan, Zeng-Guang↗

NASA NTRS2004

Partially Premixed Flame (PPF) Research for Fire Safety

Incipient fires typically occur after the partial premixing of fuel and oxidizer. The mixing of product species into the fuel/oxidizer mixture influences flame stabilization and fire spread. Therefore, it is important to characterize the impact of different levels of fuel/oxidizer/product mixing on flame stabilization, liftoff and extinguishment under different gravity conditions. With regard to fire protection, the agent concentration required to achieve flame suppression is an important consideration. The initial stage of an unwanted fire in a microgravity environment will depend on the level of partial premixing and the local conditions such as air currents generated by the fire itself and any forced ventilation (that influence agent and product mixing into the fire). The motivation of our investigation is to characterize these impacts in a systematic and fundamental manner.

Puri, Ishwar K.↗

NASA NTRS2004

Lifted Partially Premixed Flames in Microgravity

Lifted Double and Triple flames are established in the UIC-NASA Partially Premixed microgravity rig. The flames examined in this paper are established above a coannular burner because its axisymmetric geometry allows for future implementation of other non-intrusive optical diagnostic techniques easily. Both burner-attached stable flames and lifted flames are established at normal and microgravity conditions in the drop tower facility.

Lock, Andrew J.↗

NASA NTRS2003

Gravity Effects Observed In Partially Premixed Flames

Partially premixed flames (PPFs) contain a rich premixed fuel air mixture in a pocket or stream, and, for complete combustion to occur, they require the transport of oxidizer from an appropriately oxidizer-rich (or fuel-lean) mixture that is present in another pocket or stream. Partial oxidation reactions occur in fuel-rich portions of the mixture and any remaining unburned fuel and/or intermediate species are consumed in the oxidizer-rich portions. Partial premixing, therefore, represents that condition when the equivalence ratio (phi) in one portion of the flowfield is greater than unity, and in another section its value is less than unity. In general, for combustion to occur efficiently, the global equivalence ratio is in the range fuel-lean to stoichiometric. These flames can be established by design by placing a fuel-rich mixture in contact with a fuel-lean mixture, but they also occur otherwise in many practical systems, which include nonpremixed lifted flames, turbulent nonpremixed combustion, spray flames, and unwanted fires. Other practical applications of PPFs are reported elsewhere. Although extensive experimental studies have been conducted on premixed and nonpremixed flames under microgravity, there is a absence of previous experimental work on burner stabilized PPFs in this regard. Previous numerical studies by our group employing a detailed numerical model showed gravity effects to be significant on the PPF structure. We report on the results of microgravity experiments conducted on two-dimensional (established on a Wolfhard-Parker slot burner) and axisymmetric flames (on a coannular burner) that were investigated in a self-contained multipurpose rig. Thermocouple and radiometer data were also used to characterize the thermal transport in the flame.

Puri, Ishwar K.↗

NASA NTRS2003

Interaction Between Flames and Electric Fields Studied

The interaction between flames and electric fields has long been an interesting research subject that has theoretical importance as well as practical significance. Many of the reactions in a flame follow an ionic pathway: that is, positive and negative ions are formed during the intermediate steps of the reaction. When an external electric field is applied, the ions move according to the electric force (the Coulomb force) exerted on them. The motion of the ions modifies the chemistry because the reacting species are altered, it changes the velocity field of the flame, and it alters the electric field distribution. As a result, the flame will change its shape and location to meet all thermal, chemical, and electrical constraints. In normal gravity, the strong buoyant effect often makes the flame multidimensional and, thus, hinders the detailed study of the problem.

Yuan, Zeng-Guang↗

NASA NTRS2001

The Behavior of Methane-Air Partially Premixed Flames Under Normal- and Zero-G Conditions

Partially premixed flames (PPFs) represent a class of hybrid flames containing multiple reaction zones. These flames are established when less than stoichiometric quantity of oxidizer is molecularly mixed with the fuel stream before entering the reaction zone where additional oxidizer is available for complete combustion. This mode of combustion can be used to exploit the advantages of both nonpremixed and premixed flames regarding operational safety, lower pollutant emissions and flame stabilization. A double flame containing a fuel-rich premixed reaction zone, which is anchored by a nonpremixed reaction zone, is one example of a partially premixed flame. A triple flame is also a PPF that contains three reaction zones, namely, a fuel-rich premixed zone, a fuel-lean premixed zone, and a nonpremixed reaction zone. Herein we focus on two aspects of our investigation, one involving the development of optical diagnostics that can be used on a microgravity rig, which has been recently fabricated, and the other on the numerically predicted differences between normal- and zero-gravity PPFs. Both the measurements and simulations examine the detailed structure of methane-air PPFs stabilized on a Wolfhard-Parker slot burner.

Puri, Ishwar K.↗

NASA NTRS1999

DARTFire Sees Microgravity Fires in a New Light--Large Data Base of Images Obtained

The recently completed DARTFire sounding rocket microgravity combustion experiment launched a new era in the imaging of flames in microgravity. DARTFire stands for "Diffusive and Radiative Transport in Fires," which perfectly describes the two primary variables--diffusive flow and radiation effects--that were studied in the four launches of this program (June 1996 to September 1997). During each launch, two experiments, which were conducted simultaneously during the 6 min of microgravity, obtained results as the rocket briefly exited the Earth s atmosphere.

Olson, Sandra L.↗

NASA NTRS1997

Structure of Microgravity Transitional and Pulsed Jet Diffusion Flames

This paper describes results obtained in a study of pulsed gas jet diffusion flames to better characterize the recently observed vortex/flame interactions in microgravity transitional and turbulent diffusion flames, and to improve the understanding of large-scale structures in corresponding normal-gravity flames. In preparation for a space experiment, tests were conducted in the 5.18-Second Zero-Gravity Facility of the NASA Lewis Research Center. Both unpulsed and pulsed laminar flames were studied and numerical modeling of these flames was carried out for data comparison and model validation. In addition, complementary tests for a series of unpulsed flames were conducted on-board the NASA KC-135 research aircraft. The microgravity transitional and turbulent gas-jet diffusion flames have been observed to be dominated by large-scale disturbances, or structures. These structures first appear intermittently in the flame at Reynolds numbers (based on the cold jet injection properties) of about 2100. With increase in injection Reynolds number, the rate of intermittent disturbances increases until the generation becomes continuous at Reynolds numbers of 3000 and higher. The behavior of these structures depends upon the velocity and temperature characteristics of the jet/flame shear layer. These characteristics are different in normal gravity and microgravity.

Bahadori, M. Yousef↗

NASA NTRS1997

Characteristics of Non-Premixed Turbulent Flames in Microgravity

The overall objectives of this research are: (1) to obtain and analyze experimental data on flame images, and the spatial and temporal distributions of temperature, radiation, velocity and gas-phase species in microgravity turbulent gas-jet diffusion flames; and (2) to utilize these data to validate and refine the existing predictive capabilities. Work on this project commenced in June 1996. The first investigations on turbulent gas-jet diffusion flames in microgravity were initiated by Bahadori and co-workers in 1991. These studies have shown that significant differences exist in the transition processes in normal-gravity and microgravity flames, and that the turbulent flames in microgravity behave very differently as compared to their buoyancy-dominated normal-gravity counterparts. For example, in the transition regime while the visible flame height, for given fuel and nozzle size, in normal gravity decreases, the height of the microgravity flame increases. In the fully developed turbulent regime, the normal-gravity flame height is independent of injection velocity, whereas the microgravity flame height continues to increase, although at a lower rate than in the laminar and transitional regimes. Other differences between the normal-gravity and microgravity flames arise in the jet shear-layer instability characteristics, extent of the transitional regime and blow-off limit characteristics.

Hegde, Uday↗

NASA NTRS1997

Diffusive and Radiative Transport in Fires Experiment: DARTFire

A low velocity, opposed-flow, flame spread experiment designed for execution on a sounding rocket is described. Early results of infrared and ultraviolet-visible imaging using video cameras and narrow band filters are described along with planned digital image data reduction. Measured and computed spread rates show that the classical thermal regime for flame spread over thick PMMA persists, for 50% O2, down to about 5 cm/s, at which point a transition to a microgravity regime in which radiation eventually leads to extinction in at least a quiescent environment. The microgravity regime of flame spread is then distinct from the thermal and kinetic regimes previously identified.

Olson, Sandra L.↗