Search NASA⌕ Search

Engineering topics

Heidet, F.

Publications and source records attributed to Heidet, F..

At least 19 records

Full Length Assembly Testing in PELICAN (Final Report)

In support of the development of the U.S. Department of Energy (DOE) Versatile Test Reactor (VTR), a thermal hydraulics test facility was constructed to generate experimental measurement of the pressure drop across a single full-scale assembly containing prototypic axial reflectors, fuel, and plena components. Constructed and operated at Argonne National Laboratory, the Pressure drop Experimental Loop for Investigations of Core Assemblies in Nuclear reactors (PELICAN) facility was designed to achieve hydraulic conditions identical to those anticipated for a full-scale fuel assembly located in the VTR core in the region with the highest flow rate. Using water as surrogate for liquid sodium, the flow loop was operated at elevated temperatures and pressures to match the thermophysical properties of liquid sodium and ensure matching Reynolds and Euler numbers. The measurement objectives for data generated from this test facility was driven primarily by the validation needs for code calculations and simulations of the reference VTR core. These objectives focused on the need to validate pressure drop results across the various segments of the fuel assembly as they relate directly to the pumping power and safety of the reactor. Presented in this report are experimental results and analytical comparisons based on testing of a full-length assembly in PELICAN. Housed within a hexagonal test section extending 3.4 m in length, the tested assembly features a prototypic lower reflector, grid plates, wire-wrapped rod bundle, upper reflector, and exit region. The rod bundle extends over 1.5 m in length and contains 217 individual wire-wrapped rods with dimensions that best reflect the reference VTR design. The as-tested bundle assembly was fabricated using 316 stainless steel 0.25-inch (6.35-mm) diameter rods wrapped with 0.04-inch (1.016-mm) diameter wire at a helical pitch of 10.51 inch (26.6 cm). Details of the method for in-house wire-wrapping, assembly, and installation are provided later in this report. Experimental measurements of pressure drop at 19 positions along the test assembly were recorded for a range of flow conditions, with special attention paid to key locations within the assembly, including component inlet and outlet, transition, and wire-wrapped rod bundle regions. Testing conditions were based on 110°C water with flow rates ranging from 50 to 450 GPM (3 to 27 kg/s) at the inlet of the test assembly generating Reynolds numbers and velocities up to ~8.0×10 4 and ~7.8 m/s, respectively, within the rod bundle region. Non-dimensional values for the friction factor were then calculated based on these experimental measurements and compared against those predicted by various analytical correlations available from open literature. Predictions by the upgraded Cheng and Todreas, Rehme, and Novendstern correlations fell within 4% to those values measured experimentally.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Updated Reference VTR Core for CD-1

A preliminary reference core design was previously developed for the Versatile Test Reactor. The main features are that it is a 300 MW th sodium-cooled fast reactor using ternary metallic fuel U-20Pu-10Zr and able to achieve peak fast fluxes (E n > 0.1 MeV) in excess of 4.0x10 15 n/cm 2 -s. The plutonium in the fuel was assumed to be “reactor grade”, with a fissile quality of about 72% (i.e., 239 Pu and 241 Pu comprise 72% of the plutonium isotopes), and the uranium was assumed to be low-enriched uranium with 5% 235 U. This preliminary core design has been used through the CD-0 phase of the VTR project. Progression of the work after CD-0 led to revising, updating and refining the reference VTR core design, based on considerations from the various VTR teams: fuel, experiment, safety, and plant design teams. The objective of this report is to summarize the various changes made and details added to the model, to provide a description of the updated reference VTR core design and of its performance characteristics. This includes the traditional reactor physics characteristics, fuel cycle details, reactivity coefficients, temperature distributions, control rod worths and shutdown requirements. All of these define the updated “reference VTR core” intended to be used through CD-1.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Versatile Test Reactor Conceptual Core Design

The VTR is a 300-MW(thermal) sodium-cooled fast reactor (SFR) designed for the specific purpose of delivering unique testing capabilities to enable the advancement of all reactor technologies. With its flux level, irradiation volume, and operational flexibility, the VTR will enable accelerated testing of materials, fuels, and various components needing irradiation testing. Proven SFR technologies and design approaches have been leveraged in designing the VTR core, ensuring the highest possible readiness level. This resulted in the VTR using ternary metallic fuel and delivering fast flux levels in excess of 4 x 10 15 n/cm 2 ∙ s over large useful volumes, corresponding to about 60 dpa/year in steel. As part of the design efforts, the VTR core performance has been determined for a representative configuration, ensuring that the reactivity control systems offer sufficient shutdown margins, that the core can be safely cooled in all situations, and that reactivity feedback coefficients are conducive to a favorable safety behavior. Furthermore, the incorporation of features such as fuel assembly storage in the shield region supports the flexible and reliable operation of the VTR. Additional design work has been ongoing as well. This includes thorough shielding performance evaluations to ensure safe operation of the VTR, verification and validation of the design tools used to achieve compliance with Nuclear Quality Assurance (NQA-1) requirements, early assessment of the impact of irradiation experiments on the core performance envelope and associated margins, and in-depth uncertainty quantification efforts to quantify the anticipated range of performance characteristics. An experimental program supporting the VTR core design has been set up, with the current focus being on thermal-hydraulic experiments. The purpose of this experimental program is to obtain confirmatory measurements to serve directly as part of the core design basis or as part of the validation cases supporting the simulation tools used.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Benchmark Specification for FFTF LOFWOS Test #13

The Fast Flux Test Facility (FFTF) at the Hanford site in Washington was designed by the Westinghouse Electric Corporation for the U.S. Department of Energy. FFTF was a 400 MW thermal, oxide-fueled, liquid sodium cooled test reactor, built to assist development and testing of advanced fuels and materials for fast breeder reactors. After reaching criticality in 1980, FFTF operated until 1992, providing the U.S. Department of Energy (DOE) with the means to test fuels, materials, and other components in a fast neutron flux environment. In July 1986, a series of unprotected transients (with the plant protection system intentionally disabled) were performed in FFTF as part of the passive safety demonstration program. Among these were thirteen loss of flow without scram (LOFWOS) tests. The goals of this program included confirming the liquid metal reactor safety margins, providing data for computer code validation, and demonstrating the inherent and passive safety benefits of specific design features. The test defined in this benchmark is LOFWOS Test #13, which was initiated at 50% power and 100% flow with the pump pony motors turned off. This benchmark specification is intended to support collaborative efforts within international partnerships on the validation of simulation tools and models in the area of Sodium-cooled Fast Reactor (SFR) safety. Validated tools and models are needed to evaluate SFR inherent safety characteristics and assess the impact of passive design features in response to accident initiators. Comparisons with experimental data and the results of safety analyses from other groups create unique opportunities to improve predictive capabilities of computational codes and methods for SFR modeling and simulation. The conditions of the LOFWOS test along with the feedback from FFTF’s limited free bow core restraint system and the novel passive reactivity control Gas-Expansion Modules (GEMs) pose a very challenging and uniquely valuable benchmark exercise.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Multiphysics Analyses of the Bottom Components of the 3D Printed Transformational Challenge Reactor

This research presents multi-physics analyses on the bottom components of the Transformational Challenge Reactor (TCR) facility. These components include the bottom axial reflector and the steel exit cone. The bottom axial reflector is made of pure silicon carbide elements hosting helium cooling channels These elements are 3D printed and therefore can host any arbitrary shape of the helium cooling channels. The design of the bottom reflector considers the neutronics and thermo-fluid dynamics performances as well as the manufacturing process optimization. More precisely, the best design of the bottom reflector reduces neutron leakage by avoiding straight cylindrical helium channels that facilitate neutron leakage, minimizes the helium flow pressure drop, and reduces the number of 3D printed silicon carbide pieces. The exit cone steel structure collects the hot helium from the bottom fuel assemblies and channels the cold helium to the top of the fuel assemblies. The steel simultaneous contact with hot and cold helium flows sets a large thermal gradient. Different designs of the exit cone are proposed to reduce the steel equivalent stress from the helium thermal load. The multi-physics analyses have been performed using Ansys Fluent, Ansys Mechanical, STAR-CCM+, and Serpent computer programs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Benchmark Exercise for the Control Rod Swelling Evaluation

The VTR core has six reactivity control assemblies and three safety assemblies. The control assemblies or primary control rods are adjusted during the normal operation to balance the core reactivity and to control the reactor power. A typical control assembly radial layout is presented in Figure 1. The figure shows the swelled absorber (B 4 C) rod. Initially, helium gas fills the gap between the pin and the cladding before irradiation swelling takes place. For VTR, HT9 steel was selected as the cladding and duct material. The main neutron absorbing material used in the VTR is B 4 C. When residing in the core, the neutronics, thermophysical, and mechanical properties of the materials used in a control assembly will degrade due to accumulated neutron damage. Material degradation limits how long a control assembly can reside in the core. Many phenomena affect the control assembly lifetime, such as the loss of reactivity worth due to B 4 C depletion, the mechanical interaction of the absorber rod and the cladding due to B 4 C swelling, the helium gas buildup in the pin due to B-10 capture, etc. B 4 C swelling, which causes closure of the gap between the absorber rod and the cladding, is usually considered as the main limiting factor from past experience. An initial study was conducted at PNNL to evaluate the irradiation behavior of a VTR control assembly. The evaluation was performed using the CNRD2 code that was initially developed for the FFTF. The study also included an assessment of the VTR control assembly and focused on a 61-pin control assembly design, which is different from that used (37-pin design) in the core design study. The study conducted by PNNL was reviewed independently by ANL. A Python script referred to as the Control Assembly Evaluation Script (CAES) was developed for the independent review and additional assessment of 37-pin control assembly design. The script has focused on the assessment of the absorber rod swelling for its importance in determining the control assembly lifetime. CAES uses geometry, neutronics, materials data as input to predict the swelling of the absorber rod during its residence in the reactor core. The results from CAES showed some non-negligible differences against the PNNL results. Some of the differences can be attributed to the different interpretation of the control rod assembly dimensions. To resolve this issue, a benchmark exercise was proposed. The benchmark specification was developed by PNNL. The benchmark exercise was performed independently at PNNL and ANL using different codes/scripts (CRND2 and CAES). This memo documents the results calculated using the different codes. However, this report is limited to presenting the results obtained. Further investigation of the cause of the observed difference will be performed as part of future activities, pending continuation of the VTR program.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

PELICAN Status Report for Year 2021

The Pressure Drop Experimental Loop for Investigations of Core Assemblies in Advanced Nuclear Reactors, PELICAN, is a novel experimental facility designed and constructed to recreate the prototypic full scale hydraulic flow conditions for the Versatile Test Reactor (VTR) currently under development by the U.S. Department of Energy. To support VTR design efforts, PELICAN is used to replicate VTR’s primary heat transport system (PHTS) in the core assembly region. The measurement objectives for data generated from this test facility are to mimic the prototypic VTR assembly and to meet the validation needs for code calculations and simulations of the reference design for the VTR core. These objectives focus on the need to validate pressure drop results across the various segments of the fuel assembly, including the axial reflectors, fuel, and transition regions, as they relate directly to the pumping power and safety behavior of the reactor. In the following sections, the major milestones for the experimental work performed on PELICAN over the calendar year (CY) 2021 are presented. In the next section, we discuss the assembly and shakedown testing of the facility. In Section 3, an analysis of the errors in the major measurements is performed. In Section 4 and 5 we present the results from the first set of test articles placed inside the loop. The design of the remaining test articles as part of the full assembly are shown in Section 6 and the conclusion and path forward for the following year, CY22 is given in the final section.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Conceptual Design of the Transformational Challenge Reactor

The Transformational Challenge Reactor is a 3-MW(thermal) helium-cooled experimental nuclear reactor designed using an additive manufacturing–informed agile design process. This design process leverages rapid prototyping and advanced materials from emerging additive manufacturing technologies, key characteristics that enable rapid design maturation. The resulting core design incorporates a blend of advanced reactor technologies into an intermediate-spectrum microreactor, including conventionally manufactured tristructural isotropic (TRISO) fuel particles in an advanced manufactured SiC fuel element and a solid yttrium hydride moderator encapsulated in steel. Matured during the design effort, these technologies are incorporated with additively manufactured steel support and fluidic structures to form a 75-cm-outer-diameter cylindrical active core region. Below and above the active core region are axial SiC reflectors, which are housed inside the reactor pressure vessel. The reactor is controlled with an annular shroud actuated external to the pressure vessel in the gap between the pressure vessel and a steel radial reflector. A safety rod is at the center of the core to shut down the reactor when necessary. Helium pressurized at 5 MPa is forced into the pressure vessel below the core and around the core to the top plenum before it is forced down through the axial reflectors and the active core region. The primary pressurized helium loop is operated up to 500°C and includes the pressure vessel, the circulator, and the hot side of a helium-to-air heat exchanger. The secondary loop rejects all heat from the primary loop to ambient air through a heat exchanger. A vented temporary confinement building contains the entire primary loop, with penetrations for a stack, cooling, and the secondary ambient air loop. Finally, this is the first advanced nuclear microreactor designed using additive manufacturing technologies, demonstrating their applicability in an accelerated advanced design process.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Assessing Fuel Cycle Options for Elysium Molten Chloride Salt Fast Reactor from Spent Nuclear Fuel, Plutonium, and Depleted Uranium (Final CRADA Report)

Argonne National Laboratory performed calculations in order to determine the viability of various mode of operation and operating conditions for the reactor designed by Elysium Industry. The reactor description, operating conditions, startup fuel composition, and other relevant information were provided by Elysium to Argonne. The tools currently available at Argonne were used to perform the calculations and provide an assessment for the various cases agreed upon. The results were shared with Elysium.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Serpent and MCNP Calculations of the Energy Deposition in the Transformational Challenge Reactor

This paper focuses on the calculation of the energy deposition in the Transformational Challenge Reactor by two major Monte Carlo codes: Serpent and MCNP. The first software computation relies on Kinetic Energy Released per unit Mass (KERMA) factors while the second one relies on Q-values. The results from these two independent computation methodologies are in very good agreement; however, Serpent runs much faster than MCNP (for the same computational model) and allows for a detailed energy deposition distribution from a 1-mm-side square mesh with a relative statistical error between 0.5% and 1%. This detailed energy deposition is suitable for multiphysics analyses aimed at design optimizations. In order to calculate the energy deposition, Serpent needs enhanced ACE files (distributed by the software developers). Unlike other Monte Carlo software that uses inputs based on Python or Java languages, the Serpent input syntax is very similar to that of MCNP; a Python script can convert a MCNP input to a Serpent input in seconds. For simulations not requiring the calculation of the energy deposition, Serpent can also read nuclear data from MCNP ACE files, which eventually improves the comparison of the results of the two codes.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Introduction of the PELICAN loop, a Full-Scale Pressure Drop Test Facility

The Versatile Test Reactor (VTR) is a test reactor currently under development by the US Department of Energy. This reactor will rely on fast neutrons enabling novel and wide-ranging experiment to support the development of the various advanced reactor technologies. With the high flux achievable, accelerated testing of fluid and materials will be made possible. To support VTR design efforts [1], an experimental facility has been designed and constructed at Argonne National Laboratory to recreate the hydraulic flow conditions within the VTR’s primary heat transport system (PHTS). This facility, the Pressure drop Experimental Loop for Investigations of Core Assemblies in advanced Nuclear reactors, PELICAN, measures the pressure drop across a full-scale fuel assembly containing prototypic axial reflectors, fuel, and plena components. Here, we first describe the design considerations required to recreate aspects of the VTR. Then we discuss the design and construction of PELICAN to address these design requirements, the design and construction of the test articles placed inside PELICAN’s test section, and finally present some of the first experimental results.

Grannan, A. M.↗

ARC Software Validation Work for the FFTF Reactor

Extensive efforts have been carried out at ANL for the verification and validation of the Argonne Reactor Codes (ARC) software package currently used for the design of Versatile Test Reactor (VTR). The ARC software package consists of steady state neutronics and thermal hydraulics modeling capabilities which are being used by the VTR program to develop most of the VTR reactor design details which will be part of the licensing application. It is anticipated that this software will continue to be used for the design work and for initial operations although additional software may be introduced at a later time. The validation work was focused primarily on obtaining validation data consistent with VTR and usable for the ARC software. Because no critical facilities or operating fast spectrum reactors are available to do experiments for the VTR, the next best option is to identify historical experimental data that can be used as validation data. Early on in VTR, the ZPPR-15 set of experiments was identified as good validation data because of 1) the availability and quality of the data, 2) existing staff that are already familiar with the experimental machine and measurements, 3) most of the ZPPR-15 loadings of interest have already been processed into ARC models, and 4) a full uncertainty quantification has already been done for several loadings of ZPPR-15. The FFTF startup and operations data was identified as the most consistent reactor type that has validation data usable for VTR. Finally, the EBR-II fuel depletion measurements were identified as the best available validation data for VTR. It is important to note that both the FFTF and EBR-II reactors typically come with higher uncertainties than the ZPPR. In the frame of the discussed verification and validation efforts, the present document discusses the analysis of selected FFTF measurements included in the benchmark specifications of the International Reactor Physics Experiment (IRPhE) handbook. The FFTF reactor core configurations from the benchmark specification are presented in Section 2. The analysis is performed with the use of the ARC code suite available at ANL for fast reactor studies and is discussed in Section 3. The reactor parameters from the benchmark include criticality, neutron spectra, effective delayed neutron spectra, control rod worth, isothermal temperature coefficient and low energy gamma-ray spectra. The calculated values and the comparison with the experimental data is discussed in Sections 4 to 9 for each considered reactor parameter. Finally, conclusions are presented in Section 10.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Performance of HALEU and HEU-Fueled Nuclear Thermal Propulsion Reactors

Interplanetary spaceflight may be significantly improved by rockets that utilize nuclear thermal propulsion (NTP) instead of the chemically propelled rockets in use today. To be efficient, NTP reactors must be light, which presents unique design opportunities and challenges to reactor designers. One such opportunity is the enrichment of the nuclear fuel that powers the NTP reactor. The use of high-enriched uranium (HEU) instead of high-assay low-enriched uranium (HALEU) will result in a lower mass of fuel required but may present additional challenges beside the mass considerations, such as proliferation concerns, availability, public acceptance and authorization basis. Whether or not a NTP reactor fueled with HEU is significantly lighter than its HALEU counterpart is unclear and an assessment has been performed here as part of the Mars Transportation Assessment Study. This report assesses the impact of reducing the fuel enrichment form HEU (93 wt.% 235U) to HALEU fuel (19.5 wt.% 235U) on reactor design outcomes for a conceptual NTP reactor. Two reactor designs, one fueled with HEU and the other with HALEU, were prepared based on a multi-stage design process. The neutronics and thermal-hydraulics characteristics of these reactors are compared and contrasted to illustrate the impacts of fuel enrichment. Despite differences in fuel and moderator mass, the overall mass difference between the HALEU and HEU cores was only 9%. The required core size and assembly dimensions are nearly equivalent. This finding is based on a rapid design process that targeted core volume minimization. Each features some neutronics advantages - depletion is much less significant in the HEU core, but the Doppler reactivity feedback is stronger in the HALEU core. Additional discussions are made about the possible benefits of other design changes, including the possibility of utilizing a fast-spectrum reactor. Given the scope of this assessment the findings discussed in this report are not exhaustive and are only providing an initial comparison of the most obvious design and performance parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Molten salt reactor core simulation with PROTEUS

The Nuclear Energy Advance Modeling and Simulation Program (NEAMS) of the US Department of Energy (DOE) aims to develop advanced simulation tools to aid the development of advanced nuclear technologies. The high-fidelity PROTEUS code was developed in the NEAMS program for reactor physics analysis. This paper tests the applicability of the PROTEUS code to simulate a Molten Salt Reactor (MSR). The OpenMC code based on the Monte Carlo Method was employed to generate the cross sections and to provide stochastic solutions for verification. The PROTEUS code was successfully employed to simulate the steady-state performance of an MSR represented by the ThorCon core design. The 2D lattice, 2D core, and 3D full core calculations performed by PROTEUS show good agreement with that predicted by OpenMC. Furthermore, for the nodal option within PROTEUS, the precursor drift model was also tested, and this effect resulted in a reduction of the k-eff by 300 pcm.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Preliminary In-Vessel Shielding Analysis for the Versatile Test Reactor

Shielding design is an important part of the Versatile Test Reactor (VTR) design. Various shielding implementations are required to protect workers and reactor components from damaging radiation sources. The major radiation source in VTR during operation is the prompt neutron and photon emitted from nuclear fuel fissions as well as the activated structure and coolant. Shields are needed to protect the structures located inside the reactor vessel, such as the lower grid, the barrel wall, etc., in order to limit the degradation of the materials properties as a result of neutron damage (“displacement per atom”). Another early key challenge of shielding design for a pool-typed Sodium-cooled Fast Reactor (SFR) such as VTR is the activation of the secondary sodium as to flows through the intermediate heat exchangers (IHX). For a pool-typed SFR, the IHXs are placed in the primary sodium pool inside the reactor vessel. During operation, neutrons produced in the core can reach the IHXs due to the small absorption cross section of sodium and the large mean free path of fast neutrons. The secondary sodium gets activated inside the IHX and carries some of that activity outside of the reactor vessel. This source of radioactivity contained in the secondary sodium needs to be mitigated to meet the radiation dose limit sets for personnel working at the plant. This summary focuses on describing the work performed for the in-vessel shielding design and analysis aiming at limiting the secondary sodium activation.

Fei, T.↗

Simulation of Thermal Spectrum MSR using PROTEUS

In recent years, there has been renewed interest in Molten Salter Reactors (MSRs) for their potential advantages compared to reactors that rely on solid fuel. Given the current interest for MSRs, it is a good opportunity to demonstrate that the advanced tools developed in the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program are useful for modeling MSRs. In addition, one objective of the program is to develop modeling and simulation capabilities to predict the performance and safety of all types of advanced nuclear reactor. For this study, PROTEUS [1], the primary reactor physics tool within the program, was assessed and used to model one of the preliminary core designs provided by ThorCon, one of the leading MSR companies from industry. The focus of this first step in the modeling and simulation work is to predict the core design’s steady state performance.

Fei, T.↗

Preliminary Control Rod Life Time Considerations for the Versatile Test Reactor

The Versatile Test Reactor (VTR) is a fast spectrum test reactor currently being developed under the direction of the US Department of Energy, Office of Nuclear Energy. VTR will use two independent reactivity control systems: a primary and a secondary reactivity control system. Boron carbide (B 4 C) is the favored absorber material due to the extensive domestic and international experience. The life limit of control rod is analyzed in this report, based on the depletion of B-10, diametral swelling of B 4 C pellet and pressure buildup in the gas plenum. Depletion analysis of the absorber material was performed using MCNP6. It is was shown that both the concentration of B-10 and the CR reactivity worth are about linear with the irradiation time. In the preliminary VTR design, natural boron is considered as absorber material and was determined to provide just enough reactivity worth. Several alternate design options were also analyzed to improve the control rods worth (i.e. increase the shutdown reactivity margin). Using enriched boron as absorber material could increase the control rods worth, while having several drawbacks, such as reduced core excess reactivity, shorter lifetime, and larger peak centerline temperatures. A mitigation strategy to using enriched boron is to use both natural and enriched boron in the control rod, with the natural boron in the lower region of the pins and the enriched boron in the upper region. This design option still allows increasing the CR reactivity worth significantly, while maintaining all the advantages of natural boron.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗