Search NASA⌕ Search

Engineering topics

Heisman, R. M.

Publications and source records attributed to Heisman, R. M..

16 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Heat treat fixture and method of heat treating

A heat treating fixture is disclosed in which the shape of the metal specimen is maintained by cold rolled steel support plates. Glide sheets of stainless steel, coated with boron nitride, in contact with each face of the metal specimens, allow for lateral expansion of the metal specimens without binding. Grooved support bars separate the glide sheets from the upper and lower support plates and allow flow of quenching fluid to the metal specimen.

Beuyukian, C. S.↗
NASA NTRS1978

A sharp knife for high temperatures

Electrically heated nickel-chrome-steel alloy knife may be used to cut heat resistant plastic felt and similar materials with relative ease. Blade made of commercially available alloy RA 330 retains edge at temperatures as high as 927 C.

Heisman, R. M.↗
NASA NTRS1978

Rapid leak detection with liquid crystals

Small leaks in vacuum lines are detected by applying liquid-crystal coating, warming suspected area, and observing color change due to differential cooling by leak jet. Technique is used on inside or outside walls of vacuum-jacketed lines.

Heisman, R. M.↗
NASA NTRS1978

Thermal-leak analyzer for vacuum-jacketed lines

Technique involves coating suspected area with water-soluble black paint that gives even, infrared emission. Painted area is warmed with heat gun; an infrared scanner is used to detect cooled spot on jacket exterior. Introduction of atmospheric pressure into jacket intensifies leak jet and improves test sensitivity.

Heisman, R. M.↗
NASA NTRS1978

High-temperature brazing of stainless steel

Prevention of iron contamination of platens is eliminated by placing alumina/silica ceramic-fiber blankets between platens and carbon-steel plate. Carbon-steel plates provide rigidity and improve heat transfer.

Beuyukian, C. S.↗
NASA NTRS1978

Laser wire stripping

Bench-mounted and hand-held laser units cut insulation from wires without nipping or scraping conductor. Process eliminates quality control problems and is fast, clean, precise, and repeatable.

Heisman, R. M.↗
NASA NTRS1978

Leak detector uses ultrasonics

Probe located on outer wall of vacuum-jacketed fluid lines detects leaks on inner wall. Probe picks up and amplifies vibrations that occur when gas rushes through leak and converts them to audible signal or CRT display. System is considerably simpler to use than helium leak detectors and allows rapid checks to be made as part of routine maintenance.

Heisman, R. M.↗
NASA NTRS1977

Plaster core washout tool

Tool powered by pressurized water or air removes water soluble plaster lining from Kevlar/epoxy duct. Rotating plastic cutterhead with sealed end fitting connects flexible shaft that allows tool to be used with curved ducts.

Heisman, R. M.↗
NASA NTRS1977

Semiautomatic labeling of small wires

Semi-automatic-wire labeling equipment installs heat-shrink identification sleeves on small-diameter wires for moderate-size production runs. Supply reel contains wire of desired diameter and is cut into lengths set on the measuring rolls. Required number of identification sleeves are slipped over wire, which is then placed through sleeve-releasing mechanism. Sleeves are shrunk at 350 degrees F in an infrared oven.

David, L. P.↗
NASA NTRS1976

Repair of fused silica platens

Refill/leveling technique, which consists of spreading slurry refill material to affected areas and then sanding until surfaces are flat, extends service life of platen up to 50 production cycles between downtime.

Heisman, R. M.↗
NASA NTRS1970

Use of acrylic sheet molds for elastomeric products

Molds constructed of acrylic sheet are more easily machined than metal, are transparent to ensure complete filling during injection, and have smooth surfaces free of contamination. Technique eliminates flashing on molded parts and mold release agents.

Heisman, R. M.↗
NASA NTRS1969

Microwave interferometer controls cutting depth of plastics

Microwave interferometer system controls the cutting of plastic materials to a prescribed depth. The interferometer is mounted on a carriage with a spindle and cutting tool. A cross slide, mounted on the carriage, allows the interferometer and cutter to move toward or away from the plastic workpiece.

Heisman, R. M.↗
NASA NTRS1968

System remotely inspects, measures, and records internal irregularities in piping

Video electromechanical probe visually inspects and measures internal offset and peaking of welds in relatively large piping. Irregularity dimensions are recorded on peripheral equipment consisting of video tape and X-Y plotter. The probe is used for inspection of vacuum-jacketed liquid lines that cannot be inspected externally.

Burry, F. H.↗
NASA NTRS1968

Tube dimpling tool assures accurate dip-brazed joints

Portable, hand-held dimpling tool assures accurate brazed joints between tubes of different diameters. Prior to brazing, the tool performs precise dimpling and nipple forming and also provides control and accurate measuring of the height of nipples and depth of dimples so formed.

Beuyukian, C. S.↗