Engineering topics
Publications and source records attributed to Hellbaum, R. F..
Advanced Stirling-cycle cryogenic apparatus suitable for cooling sensitive infrared detectors to very low temperatures. Working fluid in refrigerator helium. Working fluid compressed and circulated by three piezoelectrically actuated diaphragm pumps offering advantages of greater reliability, relative simplicity, and lower cost.
A direction experimental measurement was made of the skin friction in the turbulent boundary layer of three-dimensional supersonic combustor flows. A floating element configuration was designed to detect two components of the small tangential shear forces due to the flow passing over a nonobtrusive instrument. A cantilevered sensing head extending from a very sensitive piezoresistive displacement transducer simultaneously measured displacement in the axial and transverse directions to the flow. The small overall deflection means that no self-nulling is required. Consistently repeatable output from the gage during testing show the skin friction with supersonic combustion is higher than for a corresponding noncombusting flow. The results are probably accurate to within 10 percent for the mean streamwise component.
A computational technique has been developed to obtain final air data quantities for a sharp-nosed hypersonic vehicle. Pressure measurements from five flush pressure ports are the only input needed. Four of the ports are installed around the forebody circumference and the fifth is on the nose. The pressure model is based on Lees-modified Newtonian method and corrected by pressure data from computational fluid dynamics analysis. Although this approach is similar to that used for the blunt-nosed space shuttle, it is designed specifically for a sharp-nosed aircraft. The potential of this method has been demonstrated, especially in obtaining values for dynamic pressure and angle of attack.
Sensors, instrumentation, and test techniques proposed for the Hypersonic Flight Instrumentation and Research Experiment are discussed. The project is concerned with Mach 4 to 16 flight at pressure altitudes of 50,000 to 150,000 feet. The developmental instrumentation for the program includes angle-of-attack sensors, transition sensors, skin-friction sensors, particle sensors, species-concentration sensors, and temperature and heat flux sensors. Support instrumentation (required to monitor basic flight parameters and to supply data from which the performance of the developmental instruments may be evaluated) considered include surface pressure sensors, inertial instrumentation, magnetic attitude sensors, and signal conditioning and data transmission instrumentation.
A sensor that measures the rate of change of total energy of an airplane with respect to the airstream has been evaluated. The sensor consists of two cylindrical probes located on the fuselage of a transport airplane, an in line acoustic filter, and a pressure sensing altitude rate transducer. Sections of this report include the sensor description and experimental configuration, frequency response tests, analytical model development, and flight test results for several airplane maneuvers. The results section includes time history comparisons between data generated by the total energy rate sensor and calculated data derived from independent sources.
Wind shears can create havoc during aircraft terminal area operations and have been cited as the primary cause of several major aircraft accidents. A simple sensor, potentially having application to the wind-shear problem, was developed to rapidly measure aircraft total energy relative to the air mass. Combining this sensor with either a variometer or a rate-of-climb indicator provides a total energy-rate system which was successfully applied in soaring flight. The measured rate of change of aircraft energy can potentially be used on display/control systems of powered aircraft to reduce glide-slope deviations caused by wind shear. The experimental flight configuration and evaluations of the energy-rate system are described. Two mathematical models are developed: the first describes operation of the energy probe in a linear design region and the second model is for the nonlinear region. The calculated total rate is compared with measured signals for many different flight tests. Time history plots show the tow curves to be almost the same for the linear operating region and very close for the nonlinear region.
The effects of certain parameter variations on the performance characteristics of laminar, proportional, jet-deflection fluidic amplifiers were studied. The matching and staging of amplifiers to obtain high pressure gain was included, but dynamic effects were not. The parameter variations considered were aspect ratio, setback, control length, splitter distance, receiver-duct width, width of center-vent duct, and bias pressure. Usable pressure gains of 19 per stage were achieved, and 5 amplifier stages were integrated to yield an overall pressure gain of 2,000,000.
An experimental program was initiated at Langley Research Center to study the effects of various parameters on the design of laminar proportional beam deflection amplifiers. Matching and staging of amplifiers to obtain high-pressure gain was also studied. Variable parameters were aspect ratio, setback, control length, receiver distance, receiver width, width of center vent, and bias pressure levels. Usable pressure gains from 4 to 19 per stage can now be achieved, and five amplifiers were staged together to yield pressure gains up to 2,000,000.
A flueric beam-deflection amplifier and a method of controlling the same are described. Either a single or a series of cascaded fluid amplifier units are provided and each one of which may include the usual power nozzle, control nozzles, outlet passages and vent passages. All vent passages of each fluid amplifier unit lead to an enclosed vent outlet chamber which is connected to the ambient environment or to a return manifold through a variably restricted passage. To control the fluid amplifier unit, power and control stream pressures are first established, after which the restricted passage is reduced to regulate the input bias, the gain and the input impedance of the fluid amplifier unit.
Gate performance is not adversely affected by normal dimensional variations encountered in fabrication and it operates throughout full loading range. Flow from one control must be sufficiently monostable to allow initial attachment and upon switching, return to outer wall. Venting must be adequate.
Low-cost fabricating technique produces minute, complex air passages in fluidic devices. Air jet interactions in these function as electronic and electromechanical control systems. Wax cores are fabricated without distortion by two-wax process using nonsoluble pattern-wax and water-soluble wax. Significant steps in fabrication process are discussed.
Monolithic precision castings using photoetched plastic and lost-wax investment techniques
Jet shoes for space locomotion during extravehicular activity
Principle of operation and static performance data of flueric AND gate, using wall attachment principle
Effects of geometrical design parameters on vortex rate sensor flow patterns