Henken, William | Search NASA

DOE OSTI2023

Encapsulation Residual Stress and Ferrite Loss in Inductive Coil Assemblies

As inductive wireless charging reaches higher power levels, thermal management and mechanical durability become more critical. To address these concerns, past works have demonstrated the benefit of encapsulating coil assemblies in thermally conductive materials. However, due to the sensitivity of the MnZn ferrites commonly used in coil assemblies to mechanical stress, care must be taken to avoid creating large stresses in the ferrite that cause higher hysteresis loss. The stress formation in the encapsulant curing process is overviewed and modeled and an experiment is performed to demonstrate the effect in a small-scale coil assembly. Finally, the effect is shown in the reduced coil-coil efficiency of a first generation high power inductive power transfer prototype using a stiff epoxy compared to better performance in a second prototype using a softer thermally-conductive silicone encapsulant.

Foote, Andrew↗

DOE OSTI2022

Development of Large Scale Extrusion Deposition for Structural Applications

Large Scale Extrusion Deposition (LSED) is an evolving additive manufacturing (AM) technology that research, such as that taking place at Oak Ridge National Laboratory (ORNL) and companies like Local Motors, are continuing to utilize and develop new applications. A major LSED application of interest has been molds and tooling as it allows for much shorter production time and lower cost. However, interest has been expanding into using LSED for more structural applications due to more frequent use of high performing polymer composites as feedstock. The use of LSED for structural applications is of particular interest to Local Motors as it is currently being used to create commercially viable, energy efficient electric vehicles. LSED offers a unique opportunity when compared to traditional manufacturing methods as it can significantly reduce the number of components necessary, while decreasing embodied energy and carbon emissions. Even with these benefits however, it is important that LSED is properly understood from a structural aspect as this field has not been as heavily researched as tooling. To ensure a high level of safety and repeatability is an essential responsibility of a manufacturer whose products are structural in nature. As such it is important to understand the materials and LSED process to make structural objects that the manufacturer can be confident in. The main goals of this project were to: develop and investigate materials that are of interest for structural LSED applications, further develop and understand the current machines used in LSED and develop simulations tools of LSED and the mechanical properties of the created structure. Material development focused on composite materials that have high mechanical properties and are stable in a variety of environments. The materials were tested to determine their as printed mechanical and thermal properties as these are necessary for simulations. Once the materials were investigated thoroughly, it allowed for simulations to be performed to compare to experimental data with simulations. Materials were also vetted to determine candidates for multi-material printing. The machine development focused around the areas of process monitoring, non-destructive evaluation, and quality control. Finally, the goal of the simulations was to develop a realistic model of printed structures, including in-process simulation and dynamic simulation. The routes to get to some of these goals and the depth in which they were investigated changed throughout the project due to personnel changes and the COVID-19 pandemic. This project resulted in many valuable results such as the development of an nondestructive evaluation (NDE) technique for interlayer defects, proof of simulation for warpage in simple parts, the development and utilization of a profilometer to monitor a print for defects or inconsistencies, thorough investigation of a material used commercially for structural LSED applications and valuable experimental data on the applicability and advantages of multi-material crush structures versus their neat counterparts by creation and testing of samples.

36 MATERIALS SCIENCE↗

DOE OSTI2022

6.26 Low Cost Basalt Fiber for Automotive Applications

Vehicle lightweighting is an essential component to the automotive industry to improve fuel economy of internal combustion engine (ICE) vehicles to meet ever improving emission standards and to improve the range of electric vehicles (EV). Composite materials offer high specific modulus and specific strength, which makes them appealing for these light weighting efforts. Sheet molding compounds (SMC) are particularly interesting from an automotive perspective because of the relatively low cost and high volume of producing SMC parts. Traditionally, composite materials for automotive application are glass fiber reinforced because of the attractive price - performance ratio, but basalt fibers are a cost and recycling competitive reinforcement alternative in this market. The aim of this project was to examine the feasibility of utilizing basalt fiber for automotive applications. More specifically, an effort was made to examine different fiber sizings on basalt fiber combined with vinyl-ester (VE) resin, and their performance as part of an SMC process. In addition to offering vehicle lightweighting with fiber reinforced polymer composites, basalt fiber is a fully recyclable material and thus supports the IACMI technical goal of: Demonstrate that the technology is capable at a sufficient scale for >80% recyclability or reuse of fiber reinforced polymer composites in five years into useful components with projected cost and quality at commercial scale competitive with virgin materials on a pathway to 95% recyclability or reuse starting in ten years. Three different fiber sizings were applied to a continuous roving of basalt fiber and compared to a traditional Electrical/Chemical Resistance (E-CR) glass fiber that is typically used in these types of applications. Fiber tows were examined for Loss on Ignition percentage (LOI%), Tex, and tow strength. Some sizings clearly outperformed others, and the ability to process these fibers on a pilot scale SMC line was demonstrated. A test plan for the manufacturing and mechanical testing of SMC panels was developed. This work continues outside the time frame allocated for this project. When this work is completed, it will be added to this report and posted as Appendix C. Glass fiber reinforced SMC materials have already proven feasible as a light weighting method for traditionally steel parts like the Volkswagen (VW) Atlas lift-gate (Figure 1); this project team is seeking the feasibility of basalt fiber as a drop-in replacement for glass fiber reinforced SMC. Sizing development for basalt fibers has proven that the mechanical properties are better than E-glass and closer to S-glass, which makes it an interesting material for SMC applications. Better mechanical properties translate to less material needed to achieve load case requirement for target applications. The business case has already been demonstrated for 100,000 parts per year of glass fiber reinforced SMC Atlas lift-gates compared to traditional steel manufacturing processes. Reduced overhead and assembly costs are offset by glass fiber SMC higher cost per kg beyond 100,000 parts per year, which is still a relatively low volume for the automotive industry. For basalt fiber reinforced SMC to become feasible for automotive applications, the price-performance ratio has to be precisely determined. Based on the mechanical performance it is possible to establish a range of applications and technical solutions in which the potential of basalt SMC can be utilized, while the price of the material can be used to compile the business case for such applications. Based on these business cases and the sustainability indicators, glass fiber reinforcement (or other) materials can be directly substituted. Volkswagen’s commitment to reducing carbon emissions cannot be understated. Basalt fiber shows promise of reducing the carbon footprint in SMC materials, especially if sizing optimizations can be made with thermoplastic based SMC. To fully realize the value of basalt fiber reinforced materials, a lifecycle cost analysis should be performed on basalt’s production and recycling, and then compared against E-glass. From this assessment, a true judgement can be made on the commercialization potential of this material. Figure 1. Example of Fiber Reinforced Polymer Composite Liftgate As a conclusion, we can state that Mafic basalt fiber is not a direct replacement for E-glass or E-CR glass based on price, but should be considered a technical solution when E-glass does not provide adequate performance in a composite design and S-glass, aramid and carbon fibers are too costly. Mafic basalt fiber can be placed on the high-performance fiber spectrum next to S-glass for performance but at one third the price. It should be considered for more technically challenging structural designs wherein the performance can demonstrate 20-25% performance enhancement over E-glass to elicit more strength or a weight reduction. Both Michelman and Mafic produce thermoplastic sizings which, in combination with Nylon and polypropylene resin and fibers, can further advance high speed composite implementations while maintaining an eco-friendly manufacturing process.

36 MATERIALS SCIENCE↗