Search NASA⌕ Search

Engineering topics

Henline, William D.

Publications and source records attributed to Henline, William D..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1997

Low-density resin impregnated ceramic article and method for making the same

A low-density resin impregnated ceramic article advantageously employed as a structural ceramic ablator comprising a matrix of ceramic fibers. The fibers of the ceramic matrix are coated with an organic resin film. The organic resin can be a thermoplastic resin or a cured thermosetting resin. In one embodiment, the resin is uniformly distributed within the ceramic article. In a second embodiment, the resin is distributed so as to provide a density gradient along at least one direction of the ceramic article. The resin impregnated ceramic article is prepared by providing a matrix of ceramic fibers; immersing the matrix of ceramic fibers in a solution of a solvent and an organic resin infiltrant; and removing the solvent to form a resin film on the ceramic fibers.

Tran, Huy K.↗
NASA NTRS1997

The Effect of Diffusional Transport and Surface Catalysis on the Aerothermodynamic Heating for Martian Atmospheric Entry

For the reentry heating of 70-degree blunt sphere-cones entering Mars at velocities in excess of 6 km/sec, a study was performed to determine the magnitude of both convective and catalytic heating on the cone forebody. Case studies of the peak heating conditions for the current NASA Mars Pathfinder entry probe, as well as the peak heating conditions of the proposed NASA Mars 2001 aerobraking orbiter mission were performed. Since the actual behavior of the chemical recombination of Mars atmosphere hypersonic shock layer species on heat shield materials is not known, and no experimental studies of any consequence have been done to determine surface reaction rates for the CO2 system, a parametric analysis of various reaction schemes and surface catalytic mechanistic models was performed. In many cases the actual Mars entry probe will have a heat shield composed of an ablative material which can either partially or completely preclude the existence of catalytic surface recombination phenomena. The extent of this blockage effect has not been examined at this time and is not considered in this effort. Instead only non-ablative computations are performed to separately evaluate the full extent of the surface catalysis and related diffusional phenomena. Parametric studies include peak heating point comparisons of non-catalytic, partially catalytic and fully catalytic total surface heat transfer for three difference surface recombination catalytic mechanisms (with and without simultaneous CO + O and O + O recombination) as well as with different species diffusion models. Diffusion model studies include constant Schmidt number (equal diffusivities) and the bifurcation, approximate multi-component diffusion model. Since the gas phase reaction kinetics for the Mars CO2 based atmosphere have also not been validated, the effect of two different (fast and slow) sets of gas kinetics on heat transfer is presented.

Henline, William D.↗
NASA NTRS1996

Low Density Resin Impregnated Ceramic Article Having an Average Density of 0.15 to 0.40 G/CC

A low-density resin impregnated ceramic article advantageously employed as a structural ceramic ablator comprising a fired preform of ceramic fibers. The fibers of the ceramic preform are coated with an organic resin film. The organic resin can be a thermoplastic resin or a cured thermosetting resin. In one embodiment, the resin is uniformly distributed within the ceramic article. In a second embodiment, the resin is distributed so as to provide a density gradient along at least one direction of the ceramic article. The resin impregnated ceramic article is prepared by providing a fired preform of ceramic fibers; immersing the preform of ceramic fibers in a solution of a solvent and an organic resin infiltrant; and removing the solvent to form a resin film on the ceramic fibers.

Tran, Huy K.↗
NASA NTRS1995

Galileo Heat Shield Response Experiment Data Reduction and Analyses

The Galileo heat shield response experiment consists of 10 Analog Resistance Ablation Detectors (ARADs) embedded in the carbon phenolic heat shield. As the vehicle descends into the atmosphere of Jupiter, these ARADs will in effect measure the recession as a function of time at various locations on the heat shield. This recession data will be used to reconstruct the time-dependent shape of the vehicle. The shape data is of critical importance to the Atmospheric Reconstruction Experiment which must know mass and drag coefficient of the vehicle in order to determine the structure of the Jovian atmosphere. The data is also intrinsically useful as a database for evaluating the accuracy of our numerical codes and methodology for predicting highly radiating reentry flowfields and coupled heat shield material response. This paper will document the reduction of the data from the ARAD sensors, reconstruction of the heat shield shape history, and comparison of the actual heat shield response with previous calculations and experiments. If possible, we will also include results from new calculations which couple the shock layer flow with the transient material response.

Milos, Frank S.↗
NASA NTRS1995

Numerical Methodology For Full-Body TPS Sizing And Optimization For Access-To-Space Vehicles

This paper presents details of the methodology and numerical procedures developed at NASA Ames for full-body TEXAS sizing and optimization for Access to Space vehicle concepts. The core of the procedures is a robust implicit solver for one dimensional transient heat conduction in reusable multilayer TEXAS stackups. The solver includes an arbitrary number of material layers, contact resistances between materials, temperature and pressure dependent material and surface properties, numerous boundary-condition options, and self-adaptive time stepping. The solver is coupled with the Access-to-Space material database of 23 candidate TPS and structural materials and a thermal-environment database obtained from trajectory-based fullbody Navier-Stokes computations of the external flowfield. The thermal environment and material response are coupled through the use of T-type heat transfer coefficients. TIPS sizing and weight optimization are performed at every surface point on the vehicle based on sizing constraints which include material temperature limits, maximum backwall temperature, and cumulative interior heat flux. Typical results are presented for a lifting body concept with 10000 surface points, which required 35 minutes to compute on an SGI Indigo 2.

Milos, Frank S.↗
NASA NTRS1995

Analysis of Aerothermal Heating Over Reusable Single-Stage to Orbit Vehicles

Using the General Aerodynamic Simulation Program (GASP) with finite-rate surface catalysis and radiative equilibrium surface temperature conditions, a computational study has been conducted to predict three-dimensional aero-convective heating over the proposed reusable single-stage to orbit vehicles. The solutions for three basic classes of usable single-stage-to-orbit vehicles, including wing body, lifting body and vertical lander, are presented and compared to provide information for vehicle design. The free stream conditions used in this study occur at an altitude of 57.5 km, ambient density of 4.129e-4 kg/cubic m, and velocity of 4,849 m/s. The convective heating over the vehicle surface in both laminar and turbulent flow regimes were computed. The Baldwin-Lomax algebraic model with a modified van Driest damping factor was applied in the turbulent flow calculations. A bifurcation model which guarantees the conservation of mass diffusive fluxes was adopted to account for the multi-species mass diffusion. The effects of turbulence and surface catalysis on the surface heating are discussed in detail The solutions indicate the degree of oxygen dissociation over the leeward side is sensitive to the shape of vehicle body. Predicted convective heating over the entire surface of lifting body is strongly affected by the presence of surface catalysis. For wing body and vertical lander, the surface catalysis effect does not appear to be important in the far downstream region, and turbulence is the dominant effect on the heating prediction in this region.

Chen, Y. K.↗
NASA NTRS1994

Trajectory-based heating analysis for the European Space Agency/Rosetta Earth Return Vehicle

A coupled, trajectory-based flowfield and material thermal-response analysis is presented for the European Space Agency proposed Rosetta comet nucleus sample return vehicle. The probe returns to earth along a hyperbolic trajectory with an entry velocity of 16.5 km/s and requires an ablative heat shield on the forebody. Combined radiative and convective ablating flowfield analyses were performed for the significant heating portion of the shallow ballistic entry trajectory. Both quasisteady ablation and fully transient analyses were performed for a heat shield composed of carbon-phenolic ablative material. Quasisteady analysis was performed using the two-dimensional axisymmetric codes RASLE and BLIMPK. Transient computational results were obtained from the one-dimensional ablation/conduction code CMA. Results are presented for heating, temperature, and ablation rate distributions over the probe forebody for various trajectory points. Comparison of transient and quasisteady results indicates that, for the heating pulse encountered by this probe, the quasisteady approach is conservative from the standpoint of predicted surface recession.

RADIATIVE ABLATING FLOWFIELD A↗
NASA NTRS1994

Comparison of Coupled Radiative Navier-Stokes Flow Solutions with the Project Fire II Flight Data

A nonequilibrium, axisymmetric, Navier-Stokes flow solver with coupled radiation has been developed to use in the design of thermal protection systems for vehicles where radiation effects are important. The present method has been compared with an existing flow and radiation solver and with the Project Fire II experimental data. Very good agreement has been obtained over the entire Fire II trajectory with the experimentally determined values of the stagnation radiation intensity in the .2 to 6.2 eV range and with the total stagnation heating. The agreement was significantly better than previous numerical predictions. The effects of a number of flow models are examined to determine which combination of physical models produces the best agreement with the experimental data. These models include radiation coupling, multi-temperature thermal models, finite-rate chemistry, and a quasi-steady-state or Boltzmann assumption for the calculation of the excited electronic states. Finally, the computational efficiency of the present model is evaluated. The radiation properties model developed for this study is shown to offer significant computational savings compared to existing codes.

Olynick, David R.↗
NASA NTRS1994

Navier-Stokes Calculations For a Venus Composition Probe With Ablation And Wake Radiation

A numerical investigation is carried out to determine the magnitude of wake radiation for a proposed Venus composition probe. One of the scientific goals of the mission is to determine the atmospheric composition of Venus by examining the intensity of scattered sunlight through the wake of the vehicle during planetary entry. In the wake of the vehicle, excited particles generated in the bow shock and boundary layers absorb and emit radiation. Thus, the purpose of this study is to determine if the radiation sensor will be able to sense the incoming solar radiative flux relative to the radiative flux generated in the wake. During portions of the entry trajectory the incident surface heat flux will be high enough to produce significant ablation. Ablation products such as CN are known to be strong radiators. Also, the ablation will be driven by strong radiation emanating from the bow shock. Thus, radiation and ablation will be coupled into the Navier-Stokes flow solutions.

Olynick, David R.↗
NASA NTRS1993

Trajectory-based heating analysis for the ESA/Rosetta earth return vehicle

A coupled, trajectory based flowfield and material thermal response analysis is presented for the European Space Agency (ESA) proposed Rosetta comet nucleus sample return vehicle. The probe returns to Earth along a hyperbolic trajectory with an entry velocity of 16.5 km/sec and requires an ablative heat shield on the forebody. Combined radiative and convective, ablating flowfield analyses were performed for the significant heating portion of the shallow ballistic entry trajectory. Both quasi-steady ablation and fully transient analyses were performed for a heat shield composed of carbon-phenolic ablative material. Quasi-steady analysis was performed using the two-dimensional, axisymmetric codes RASLE and BLIMPK. Transient computational results were obtained from the one-dimensional ablation/conduction code, CMA. Results are presented for heating, temperature and ablation rate distributions over the probe forebody for various trajectory points. Comparison of transient and quasi-steady results indicates that, for the heating pulse encountered by this probe, the quasi-static approach is conservative from the standpoint of predicted surface recession.

Henline, William D.↗
NASA NTRS1991

Transpiration Cooling Of Hypersonic Blunt Body

Results on analytical approximation and numerical simulation compared. Report presents theoretical study of degree to which transpiration blocks heating of blunt, axisymmetric body by use of injected air. Transpiration cooling proposed to reduce operating temperatures on nose cones of proposed hypersonic aerospace vehicles. Analyses important in design of thermal protection for such vehicles.

Henline, William D.↗
NASA NTRS1991

Phenomenological and experimental study of the thermal response of low density silica ablators to high enthalpy plasma flows

A complete analysis of the melting-ablator governing equations is carried out for porous ablators with the purpose of establishing an approximate analytical model capable of determining surface recession, temperature, and heat flux as well as in-depth temperature profiles. A detailed dimensional analysis of the melt-flow governing equations is performed for parameters applicable to high-enthalpy flows. Results of arc-jet flow experiments performed on NASA Reusable Surface Insulation materials of different densities and over a range of stagnation pressures and heat fluxes are discussed. A dimensionless correlation for melt run-offs is derived in terms of material and flow parameters; however, it is pointed out that the accuracy of the current data is sufficient to conclude the compliance with the model.

Henline, William D.↗
NASA NTRS1991

Effect of non-equilibrium flow chemistry and surface catalysis on surface heating to AFE

The effect of nonequilibrium flow chemistry on the surface temperature distribution over the forebody heat shield on the Aeroassisted Flight Experiment (AFE) vehicle was investigated using a reacting boundary-layer code. Computations were performed by using boundary-layer-edge properties determined from global iterations between the boundary-layer code and flow field solutions from a viscous shock layer (VSL) and a full Navier-Stokes solution. Surface temperature distribution over the AFE heat shield was calculated for two flight conditions during a nominal AFE trajectory. This study indicates that the surface temperature distribution is sensitive to the nonequilibrium chemistry in the shock layer. Heating distributions over the AFE forebody calculated using nonequilibrium edge properties were similar to values calculated using the VSL program.

Stewart, David A.↗
NASA NTRS1991

Documentation of the detailed radiation property data for the radiation-ablation code RASLE

This report is a documentation of the necessary radiation property input data for the radiating shock layer simulation code RASLE. The tabulated data are required to simulate systems which are composed of oxygen, nitrogen, carbon, hydrogen, and silicon. These data are needed to compute the flowfield effects of many practical ablative, hypersonic vehicle heat shield materials. A brief outline description is provided for the RASLE code. A more detailed discussion is provided for the RASLE code non-grey gas spectral radiation model. This model is related to the required radiation property data which are tabulated at the end of the report. Other correlations needed for the RASLE simulations are not discussed, since these are automatically included in the program and no input data are required.

Henline, William D.↗
NASA NTRS1991

Aerothermodynamic heating environment and thermal protection materials comparison for manned Mars-earth return vehicles

The aerothermodynamic environment during the earth return portion of a specific manned Mars mission is studied. Particular attention is given to the earlier smaller crew return capsule and its thermal protection system requirements. Data are presented on the stagnation region of a generic Mars return capsule. Insulation material thicknesses required to maintain allowable structural temperatures throughout a prolonged heat soak period are estimated.

Henline, William D.↗
NASA NTRS1989

Transpiration cooling of hypersonic blunt bodies with finite rate surface reactions

The convective heat flux blockage to blunt body and hypersonic vehicles by transpiration cooling are presented. The general problem of mass addition to laminar boundary layers is reviewed. Results of similarity analysis of the boundary layer problem are provided for surface heat flux with transpiration cooling. Detailed non-similar results are presented from the numerical program, BLIMPK. Comparisons are made with the similarity theory. The effects of surface catalysis are investigated.

Henline, William D.↗
NASA NTRS1988

Effect of surface catalysis on heating to ceramic coated thermal protection systems for transatmospheric vehicles

This paper describes the effect of surface catalysis on the heat transfer rate to the heat shield of a typical Transatmospheric Vehicle (TAV) during ascent and atmospheric entry. Surface kinetics and optical properties obtained from arc-jet tests on candidate thermal protection systems (coated metals) were used in a reacting boundary layer code to estimate the heating distribution along the surface of a TAV. Thermochemical stability of the coatings is described in terms of reduction in emittance and loss of opacifiers from the coatings during the arc-jet tests.

Stewart, David A.↗