Search NASA⌕ Search

Engineering topics

Hernandez, Gloria

Publications and source records attributed to Hernandez, Gloria.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2014

On the Stratospheric Aerosol and Gas Experiment III on the International Space Station

The Stratospheric Aerosol and Gas Experiment III on International Space Station (SAGE3/ISS) is anticipated to be delivered to Cape Canaveral in the spring of 2015. This is the fourth generation, fifth instrument, of visible/near-IR solar occultation instruments operated by the National Aeronautics and Space Agency (NASA) to investigate the Earth's upper atmosphere. The instrument is a moderate resolution spectrometer covering wavelengths from 290 nm to 1550 nm. The nominal science products include vertical profiles of trace gases, such as ozone, nitrogen dioxide and water vapor, along with multi-wavelength aerosol extinction. The SAGE3/ISS validation program will be based upon internal consistency of the measurements, detailed analysis of the retrieval algorithm, and comparisons with independent correlative measurements. The Instrument Payload (IP), mission architecture, and major challenges are also discussed.

Hernandez, Gloria↗
NASA NTRS1994

Effect of leading- and trailing-edge flaps on clipped delta wings with and without wing camber at supersonic speeds

An experimental investigation of the aerodynamic characteristics of thin, moderately swept fighter wings has been conducted to evaluate the effect of camber and twist on the effectiveness of leading- and trailing-edge flaps at supersonic speeds in the Langley Unitary Plan Wind Tunnel. The study geometry consisted of a generic fuselage with camber typical of advanced fighter designs without inlets, canopy, or vertical tail. The model was tested with two wing configurations an uncambered (flat) wing and a cambered and twisted wing. Each wing had an identical clipped delta planform with an inboard leading edge swept back 65 deg and an outboard leading edge swept back 50 deg. The trailing edge was swept forward 25 deg. The leading-edge flaps were deflected 4 deg to 15 deg, and the trailing-edge flaps were deflected from -30 deg to 10 deg. Longitudinal force and moment data were obtained at Mach numbers of 1.60, 1.80, 2.00, and 2.16 for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.16 x 10(exp 6) per foot and for an angle-of-attack range 4 deg to 20 deg at a Reynolds number of 2.0 x 10(exp 6) per foot. Vapor screen, tuft, and oil flow visualization data are also included.

Hernandez, Gloria↗
NASA NTRS1993

An experimental investigation of a Mach 3.0 high-speed civil transport at supersonic speeds

An experimental study was conducted to determine the aerodynamic characteristics of a proposed high speed civil transport. This configuration was designed to cruise at Mach 3.0 and sized to carry 250 passengers for 6500 n.mi. The configuration consists of a highly blended wing body and features a blunt parabolic nose planform, a highly swept inboard wing panel, a moderately swept outboard wing panel, and a curved wingtip. Wind tunnel tests were conducted in the Langley Unitary Plan Wind Tunnel on a 0.0098-scale model. Force, moment, and pressure data were obtained for Mach numbers ranging from 1.6 to 3.6 and at angles of attack ranging from -4 to 10 deg. Extensive flow visualization studies (vapor screen and oil flow) were obtained in the experimental program. Both linear and advanced computational fluid dynamics (CFD) theoretical comparisons are shown to assess the ability to predict forces, moments, and pressures on configurations of this type. In addition, an extrapolation of the wind tunnel data, based on empirical principles, to full-scale conditions is compared with the theoretical aerodynamic predictions.

Hernandez, Gloria↗
NASA NTRS1990

Supersonic aerodynamic characteristics of a Mach 3 high-speed civil transport configuration

The NASA-Langley AST31 high-speed civil transport (HSCT) configuration, a blended wing/fuselage concept scaled for 250-passenger carriage over 6500 nmi, has been subjected to both CFD and wind tunnel tests; the wind tunnel tests were conducted in the Mach 1.6-3.6 range. The inability of the linear theory method to accurately predict stability levels as well as nonlinear pitching moment characteristics demonstrates the need to undertake high-order analyses as early in the design process as possible. An HSCT laminar flow capability experimental study was conducted in order to simulate 50-percent laminar flow conditions, and thereby ascertain the difference in drag relative to fully turbulent conditions.

Covell, Peter F.↗
NASA NTRS1989

Evaluation of leading- and trailing-edge flaps on flat and cambered delta wings at supersonic speeds

An experimental investigation has been conducted to evaluate the effectiveness of leading- and trailing-edge flaps on a flat and cambered wing at superconic speeds. Results from the experimental tests showed that highly complex and three-dimensional flow can occur over the wings with leading- and/or trailing-edge flaps deflected. An analysis of the data also showed that flap effectiveness varies significantly between a cambered and flat wing of identical planform and flap geometry. Mach number effects are similar for both flat and cambered wings for all aerodynamic parameters.

Hernandez, Gloria↗
NASA NTRS1988

Reduction of crossflow shock-induced separation with a porous cavity at supersonic speeds

The effectiveness of wing surface porosity in reducing boundary-layer separation induced by a cross flow shock on a conical wing in a supersonic flow was investigated in tests conducted in the NASA Langley Research Center Unitary Plan Wind Tunnel, at a Reynolds number of 2 mln/ft at Mach numbers 1.62, 1.70, 1.86, and 2.00 and with the angle of attack varying between -2 and 10 deg. A porous cavity was installed in a 57 deg swept conical wing at a location where a cross flow shock had been observed in previous tests. The porosity was varied from 11 to 22 percent, the pore hole diameter was varied from 0.025 to 0.050 in., and the cavity depth varied from 0.067 to 0.255 in. It was found that a hole of 0.025 in. in diameter is more effective than a 0.050-in. hole. However, the effectiveness of the larger holes could be increased by reducing the cavity depth, causing a closed-cavity type flow condition.

Bauer, Steven X. S.↗