Search NASA⌕ Search

Engineering topics

Herring, Andrew M.

Publications and source records attributed to Herring, Andrew M..

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Effects of the Hydrophobic Block Length Ratio of Poly(vinylbenzyl N -methylpiperidinium carbonate)- b -polyethylene- b -poly(vinylbenzyl N -methylpiperidinium carbonate) Block Copolymers for Anion Exchange Membrane Electrolysis

Electrolysis of water to produce hydrogen from renewable electricity is an extremely attractive strategy to reduce energy dependence on fossil fuels. Development of membrane and ionomer materials that maintain high performance with long lifetimes is needed. We developed and investigated the performance and durability of a series of polyethylene-based ABA triblock copolymer anion exchange ionomer and membrane (AEI, AEM) materials for anion exchange membrane water electrolysis. Poly(vinylbenzyl N-methylpiperidinium carbonate)-b-polyethylene-b-poly(vinylbenzyl N-methylpiperidinium carbonate) was synthesized with different hydrophobic/hydrophilic block ratios (1.02:1, 2.58:1, and 4.46:1) resulting in a range of ion exchange capacities (1.1–1.8 meq g –1 ) and water swelling (23–154%) characteristics. All AEMs showed full anionic dissociation, as evidenced by linear Arrhenius correlations, and excellent carbonate conductivity of 8–94 mS cm –1 at 50 °C. Hydrophilic phase separation may offer superior chemical durability by only wetting the ion-conducting region of the polymer and avoiding attack at the nonwetted backbone. We evaluated the performance and durability of these AEMs as a function of hydrophobic polyethylene (PE) content. The AEM containing the least amount of PE displayed the highest performance of 1 A cm –2 at 2.3 V but degraded at 40 mV h –1 before catastrophically failing after <3 h at 0.5 A cm –2 . With greater PE-containing AEMs, the degradation rate was reduced by 3 orders of magnitude with only a 0.2 V increase in voltage. Constant current electrolysis for 50 h resulted in a voltage change of 0.3 mV h –1 in a single-cell water electrolyzer and 1 M potassium carbonate. In a 600 h test, the voltage change in the final 200 h was impressively low for an experimental film, 58 μV h –1 . Postmortem analysis indicated that the membrane did not thin and that water becomes more tightly hydrogen-bound in the polymer after electrolysis.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Effect of Block Length on the Properties of Multiblock Polysulfone-Poly(diallylpiperidinium hydroxide) Anion Exchange Membranes

Research in anion exchange membranes (AEM)s has continued with the development of materials bearing base stable cations. Designing AEMs that microphase separate into hydroxide conductive, hydrophilic domains within a hydrophobic and mechanically robust matrix has been shown to be successful for improving AEM performance. A series of multiblock polysulfone-poly(diallylpiperidinium hydroxide) copolymers (PSf-PDApipOH) of similar hydrophobic/hydrophilic composition was prepared in which the molecular weight of the hydroxide conducting PDApipOH segments was varied. The variable hydrophilic segment molecular weight was designed to assess the impact on microphase separation, hydroxide conductivity, and water management. The multiblock copolymers investigated were prepared by condensation polymerization of preformed4-fluorophenyl sulfone terminated poly(diallylpiperidinium hexafluorophosphate) (PDApipPF6) oligomers with polysulfone monomers. The structure-property relationship between the molecular weight of the conductive PDApipOH segments and AEM performance was demonstrated by evaluation of the microphase separation, water uptake, and hydroxide conductivity. Further, membranes fabricated from the polysulfone-poly(diallylpiperidinium hexafluorophosphate) (PSf-PDApipPF6) multiblock copolymers were shown to form well-connected conductive domains by SAXS and atomic force microscopy experiments. The PSf-PDApipOH membranes were highly conductive with the maximum hydroxide conductivity reaching 62.9 mS∙cm -1 at 60°C and 95% relative humidity. Furthermore, it was demonstrated that the conductivity increased with increasing PDApipOH segment molecular weight.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Evaluating the effect of ionomer chemical composition in silver-ionomer catalyst inks toward the oxygen evolution reaction by half-cell measurements and water electrolysis

The effect of anion exchange ionomer (AEI) chemistry on the kinetics of the oxygen evolution reaction (OER) was systematically studied in both half-cell and single-cell electrolysis experiments. OER was studied in 1 M K 2 CO 3 at 50°C using an array of ionomer-silver catalyst inks deposited on Ni foam. Different ionomer modifications were investigated to optimize the OER performance. The AEI used in this work features a block copolymer backbone of polychloromethylstyrene-b-polycyclooctene-b-polychloromethylstyrene which was functionalized with either benzyltrimethylammonium (TMA) or benzylmethylpiperidinium (MPRD) quaternary ammonium cations. Here, using an MPRD quaternary ammonium cation shifted the rate determining step at high overpotentials, ultimately providing enhanced performance. Increasing the catalyst ink dilution was also found to substantially improve mass activity and catalyst utilization (increase from 35 to 88 A g –1 Ag), likely by reducing the ionomer thickness and decreasing transport resistances. In the final ionomer modification, the Ni foam substrate was leveraged to partially hydrogenate the polycyclooctene midblock to be polyethylene-like at the Ni interface. A significant increase in the electrochemical surface area (Cdl increased from 8.8 to 20.8 mF cm –2 ) and performance (by 47 mA cm –2 or 29 A g –1 Ag) was observed with the incorporation of polyethylene. Kinetic results from half-cell experiments were validated via single-cell anion exchange membrane electrolysis experiments, where the optimized electrode displayed enhanced performance in both 1 M K 2 CO 3 and DI H 2 O.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Spatially resolved performance and degradation in a perfluorinated anion exchange membrane fuel cell

Anion exchange membrane fuel cells may enable future operation with non-precious metal-based catalysts. These systems have a delicate sensitivity to operating conditions such as humidification levels and the presence of CO2 in the air oxidant stream. We present spatially resolved in-situ performance results that shed light on phenomena that are unique to anion exchange membrane fuel cells. For cell construction, a highly conductive perfluorinated anion exchange polymer was used as the membrane and the material in powder form as the ionomer. Experiments were conducted to investigate the effects of humidification, fuel/oxidant concentration, and carbonation effects on the performance and its distribution in the cell. The results indicated that (i) dry conditions at the cathode have a stronger effect than at the anode on overall cell performance, (ii) performance significantly suffered when humidification was below 90%, (iii) fuel and oxidant dilution effects lead mass-transport losses and were stronger than flow rate effects, (iv) CO2 in the cathode feed stream creates an equilibration disparity between the inlet and outlet sections and CO2 purging is affected by flooding conditions, and (v) after >500 h of operation, performance deteriorates predominantly at the inlet.

2+1D fuel cell model↗
DOE OSTI2021

Designing Anion-Exchange Ionomers with Oriented Nanoscale Phase Separation at a Silver Interface

We report performance of polymer electrolyte-based energy systems is significantly impacted by transport within the electrode catalyst layer, where ionomer thin films coat catalyst particles. Proton exchange ionomer thin films have been thoroughly characterized, but few studies have critically examined anion-exchange ionomer (AEI) thin films. Further, none have reported nanoscale phase separation for hydrocarbon AEIs, which is critical to mitigate transport resistances. In this work, a set of hydrocarbon-based AEIs with nanoscale phase separation are developed from tunable block copolymer systems composed of polyisoprene (PIp) and polychloromethylstyrene (PCMS). The effect of the PIp/PCMS ratio, architecture, and thickness on the thin-film morphology of the neutral block copolymer precursors on silicon and silver substrates is investigated using grazing-incidence small-angle X-ray scattering (GISAXS) and atomic force microscopy (AFM). AEIs are prepared by quaternizing with trimethylamine or methylpiperidine and their cation-dependent morphology is characterized at 60 °C and 95% RH. A perpendicularly aligned morphology is observed on silver, while no phase separation is observed on silicon, indicating that silver-polymer interfacial interactions drive phase separation. After quaternization, dipole-dipole interactions induce some disorder, but nanoscale phase separation is still maintained. GISAXS patterns are modeled using a Unified Fit approach to understand water uptake and swelling, and recommendations for AEI design are presented.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Optimization of anionic conductivity through the coexistence of ionomer cluster and backbone-backbone morphologies in anion exchange membranes

Random copolymers of poly(4-vinylpyridine) and polyisoprene were synthesized, and subsequently quaternized with 1-alkylbromides. The number of carbons on the pendant side-chain of the resultant comb-shaped polymer, n, ranged from 2-8. The comb-shaped polymers were crosslinked employing thiol-ene chemistry to give mechanically robust ion conducting membranes. Analysis by wide and medium-angle X-ray scattering show three morphology regimes that are dependent on the number of carbons on the pendant side-chains. When n = 2, ionomer cluster morphology was dominant, when n = 8 backbone-backbone morphology was dominant, and when n = 3-6, the membrane showed a coexistence of both ionomer cluster and backbone-backbone morphologies. Evaluation of the water uptake of the membranes showed a maximum water uptake per cation of 9.5 when n = 5 at 95% relative humidity (RH) and 60 degrees C. Finally, conductivity of the samples characterized by electrochemical impedance spectroscopy showed bromide conductivity as high as 110 mS/cm when n = 3 at 95% RH and 90 degrees C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Investigating Silver Nanoparticle Interactions with Quaternary Ammonium Functionalized Triblock Copolymers and Their Effect on Midblock Crystallinity

Interactions between silver nanoparticles and a cationic triblock copolymer significantly alter bulk material properties and can be tuned by functionalizing the polymer with different quaternary ammonium cations (QACs). In this work, poly-chloromethylstyrene-b-polycyclooctene-b-polychloromethylstyrene (PCMS-b-PCOE-b-PCMS) was quaternized with either methylpiperidinium (MPRD) or trimethylammonium (TMA). The surface interacting groups were identified using FT-IR to be the phenyl rings, the QACs from the outer blocks, and vinyl groups from the PCOE midblock. Changes in thermal characteristics and crystallinity were highly dependent on the QAC, uncovering differences in the nature of the interactions between silver and TMA or MPRD. Interactions induced by TMA greatly hinder crystalline domain formation and give rise to a higher water content, while MPRD promotes certain crystalline orientations and provides a greater degree of crystallinity with a lower water content. In this work, our findings demonstrate that bulk polymer characteristics can be tuned, a highly desirable attribute for many nanocomposite materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Ring-opening metathesis polymerization of cobaltocenium derivative to prepare anion exchange membrane with high ionic conductivity

Abstract An efficient method to incorporate a cobaltocenium cation into polymers for anion exchange membranes is described. A cobaltocenium-containing norbornene derivative has been synthesized. It can be homopolymerized, or copolymerized with norbornene, by ring-opening metathesis polymerization (ROMP) with quantitative yields. The composition of the random copolymers can be precisely controlled by adjusting the feed ratio of the monomers. Additionally, the resulting polymers can be cast into thin robust membranes. The morphology of the membranes is characterized by humidity controlled SAXS and TEM, showing disordered interconnected cobaltocenium domains. The high ionic conductivity suggests that such membranes are good candidates for anion exchange membranes.

42 ENGINEERING↗