Search NASA⌕ Search

Engineering topics

Herrmann, Steven D.

Publications and source records attributed to Herrmann, Steven D..

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Synthesis and thermophysical property determination of NaCl-PuCl3 salts

Currently, a knowledge gap exists in the available data and understanding of thermophysical properties relating to fresh fuel salts, especially those containing plutonium. These data are necessary for designing, constructing, and licensing future commercial molten-salt reactors. Thermophysical properties, such as melting temperature, salt stability, density, and heat capacity were ascertained using NaCl-PuCl3 (36 mol% PuCl3) and a more sodium rich composition containing 25 mol% PuCl3. The NaCl-PuCl3 salt mixture was synthesized for this study and contained 63.4 mol% NaCl, 36.3 mol% PuCl3 and was 99.7% pure. Upon heating, the NaCl–PuCl3 eutectic was stable at temperatures up to 800 °C. The onset of melting occurred at 451 ± 3 °C, and the enthalpy of fusion was determined to be 23.0 ± 1.4 kJ/mol. Heat capacity measurements in the liquid phase ranged from 107.7 to 91.3 J/mol.K, with an average value of 104.6 ± 11.4 J/mol.K between 500 and 650 °C. Three independent trials of the molten NaCl-PuCl3 salt found the density to be ?(T) = 3.8589 – 9.5342·10-4 T(°C). In addition, ab initio molecular dynamic simulations to calculate density and heat capacity values are included.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Estimate of Gamma Dose Rates from Arrays of Fermi-1 Blanket Elements During the MEDE Process

The Enrico Fermi Atomic Power Plant Unit 1 (Fermi-1) was a sodium-cooled fast breeder reactor located in Monroe County, Michigan. The reactor was powered by a core of enriched uranium metal alloy driver fuel, which was enveloped by an axial and radial blanket material consisting of depleted uranium metal alloyed with 3 wt.% molybdenum. There are 406 axial and 559 radial irradiated sodium-bonded Fermi-1 blanket assemblies in storage at INL, totaling 34 metric tons of heavy metal. Disposal of the Fermi-1 blanket material directly into a geological repository is prohibited due to the reactive characteristic of its bond sodium. A melt drain evaporate (MEDE) process can effectively remove bond sodium from Fermi-1 blanket material. Consequently, planning is underway to apply a MEDE process to treat the 34 metric tons of heavy metal of irradiated Fermi-1 blanket material. Given the irradiated Fermi-1 blanket material’s relatively low power history and 50+ years of decay, it can be treated in a shielded glovebox. To assess the requisite shielding, the dose rates of the Fermi-1 blanket elements in various process configurations are needed. The method to perform the dose rate calculations is to first generate an average source term and associated photon source spectra for the Fermi-1 blanket material in SCALE and then use the associated photon spectra to calculate dose rates using MCNP6.2 in seven representative geometries. Dose rates in rem/h were calculated on contact (1 cm from outer geometry surface), 30 cm away from outer geometry surface, and 1 m from outer geometry surface at axial heights spanning the length of the blanket material within the geometry. The maximum average dose rate for the single Fermi-1 radial blanket element is ~0.60 rem/h, for the Fermi-1 radial blanket assembly ~1.10 rem/h, for the single Fermi-1 axial blanket element ~0.5 rem/h, for the Fermi-1 axial blanket assembly ~1.01 rem/h, for the MEDE can ~ 0.98 rem/h, for the Fermi Storage Canister ~ 0.83 rem/h, and for the MEDE cans in the DOE Standard Canister ~0.51 rem/h. Based on these maximum average values, the bounding dose rates are assumed to be 3× the average dose rates calculated for the axial blanket material and 7.6× the average dose rates calculated for the radial blanket material, based on the distribution of Fermi-1 blanket material assembly burnup.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Experimental Observations for Anode Optimization of Oxide Reduction Equipment

The electrochemical behavior of several components has been investigated during the electrolysis of nickel oxide in LiCl-Li 2 O salt mixture at 650°C. The focus of this work is to improve anode design and shroud to increase current densities. The tested components were ceramic anode shroud porosity, porosity size, anode geometry, anode material, and metallic porous anode shroud. The goal of these experiments was to optimize and improve the reduction process. The highest contributors to higher current densities were anode shroud porosity and anode geometry.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Study of Electrorefiner Sediment Re-Chlorination Options

A study was performed to investigate re-chlorination options for electrorefiner sediment, fulfilling a DOE Level 4 milestone within the Material Recovery and Waste Form Development campaign. The study stems from the recent identification of sediment that had accumulated in a kg-scale uranium electrorefiner at Idaho National Laboratory’s Hot Fuel Examination Facility. The study involved surveying, evaluating, and recommending options for re-chlorinating, or otherwise recovering, actinides from the sediment. Several options were investigated, including chemical and electrochemical techniques on the sediment within the electrorefiner (in situ approaches) or after its removal from the electrorefiner (ex situ approaches). A baseline approach was identified, involving electrolytic reduction of the removed sediment and subsequent electrorefining. Some options were dismissed for various deficiencies, while other options were recommended for further investigation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Synthesis and characterization of uranium trichloride in alkali-metal chloride media

Given a growing interest in uranium salts for pyrochemical processing of used fuel and uranium-fueled molten salt reactors, the synthesis of uranium trichloride in alkali-metal chloride media was investigated in a series of four experiments. Specifically, uranium metal powder and uranium hydride powder were prepared and separately blended with ammonium chloride and lithium chloride – potassium chloride eutectic in two runs, while the same powders were separately blended with ammonium chloride and sodium chloride in two additional runs. Each of the lithium chloride – potassium chloride containing blends was slowly heated to 923 K, while those containing sodium chloride were heated to 1123 K. During each heat up, the ammonium chloride sublimed into gaseous ammonia and hydrogen chloride, leading to the chlorination of uranium metal or uranium hydride and the formation of molten salt solutions of the respective chlorides. Experimental conditions were incorporated in the runs to promote formation of uranium trichloride over uranium tetrachloride in the respective media. Molten samples of each run product were taken and characterized via chemical analyses, diffractometry, and microscopy. The final products from each run were dark dense ingots of the respective salt systems with uranium concentrations ranging from 44 to 51 wt%. Finally, chemical analyses and diffractometry identified the predominant presence of uranium trichloride in these systems; however, a possible minor presence of uranium tetrachloride could not be conclusively dismissed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Parametric Study of Used Nuclear Oxide Fuel Constituent Dissolution in Molten LiCl-KCl-UCl 3

Prior work identified dissolution of used nuclear oxide fuel constituents from a uranium oxide matrix into molten LiCl-KCl-UCl 3 at 500°C, prompting a subsequent series of three progressive studies (including an initial scoping study, an electrolytic dissolution study, and a chemical-seeded dissolution study) to further investigate associated parameters and mechanisms. Thermodynamic calculations were performed to identify possible reaction mechanisms and their propensities in used oxide fuel constituent dissolution. Used nuclear oxide fuels with varying preconditions from fast and thermal test reactors were separately immersed in the subject salt system to assess fuel constituent migration from the bulk fuel matrix to the salt phase in an initial scoping study. Dissolution of expected fuel constituents, including alkali, alkaline earth, lanthanide, and transuranium oxides, into the chloride salt phase varied widely, ranging from 12% to 99% in the initial study. Uranium isotope blending between the salt phase and bulk fuel matrix was also observed, which was attributed to reducing conditions in the fuel matrix. Electrolytic and chemical-seeded dissolution studies were subsequently performed to effect reducing conditions in the fuel. Other parameters, including temperature (at 500°C, 650°C, 725°C, and 800°C) and uranium trichloride concentrations (at 6, 9, and 19 wt% uranium), were investigated in the latter two studies, resulting in fuel constituent dissolution above 90%. Extents of dissolution were based on initial and final fuel constituent concentrations in the oxide fuels following operations in the salt and subsequent removal of the salt via distillation. Finally, in this series of progressive studies, oxide fuel preconditioning and in situ reducing conditions, along with elevated temperature and uranium trichloride concentrations, were the primary parameters promoting used nuclear oxide fuel constituent dissolution in accordance with identified reaction mechanisms.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Halogenation of used aluminum matrix test reactor fuel – a bench-scale demonstration with surrogate materials

In this work, experiments with surrogate materials were performed at bench scale to demonstrate a halogenation technique applicable to treatment of used aluminum matrix test reactor fuel. The technique involves dissolution and separation of aluminum from used aluminum matrix test reactor fuel in molten-halide salt systems prior to treatment and disposition of the fuel’s uranium and fission products. Demonstration of the halogenation technique was performed with neodymium metal as a non-radiological surrogate for uranium metal. Experiments involved blending forms of aluminum and neodymium metal with ammonium and lithium chloride or ammonium and lithium bromide, which upon heating decomposed into ammonia gas and the respective hydrogen chloride or bromide gas. The latter reacted with the metals to form the respective aluminum and neodymium halides. At elevated temperatures, aluminum halides gasified away from the respective neodymium halides, which fused with their respective lithium halides. Samples of fused and distillate salts were collected and analyzed, yielding extents of aluminum removal that ranged from 94.5–98.2% for chlorination runs and 91.4–97.8% for bromination runs. No neodymium was detected in the distillate fractions. Some experiments were repeated with excess reactants, and a portion of aluminum chloride distillate was processed into a consolidated waste form.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗