Search NASA⌕ Search

Engineering topics

Hertzberg, R. W.

Publications and source records attributed to Hertzberg, R. W..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Fatigue crack propagation behaviour of unidirectionally solidified gamma/gamma-prime-delta eutectic alloys

Fatigue crack propagation studies were carried out on unidirectionally solidified gamma/gamma-prime-delta (Ni-Nb-Al) alloys over an aluminum content range of 1.5-2.5% by weight. The variation of Al content of as-grown alloys did not significantly affect the crack growth behavior of these eutectic composites. The results indicate that the addition of Al to the eutectic dramatically improved the FCP behavior. The gamma/gamma-prime-delta alloy exhibited crack growth rates for a given stress intensity range that are an order of magnitude lower than those for the gamma-delta alloy. It is suggested that this difference in FCP behavior can be explained on the basis of stacking fault energy considerations. Extensive delaminations at the crack tip were also revealed, which contributed to the superior fatigue response. Delamination was predominantly intergranular in nature.

Bretz, P. E.↗
NASA NTRS1976

Conference on In Situ Composites, 2nd, Bolton Landing, N.Y., September 2-5, 1975, Proceedings

The present collection of papers deals with advances in several areas of interest in in-situ composites. Major areas discussed include solidification and structural control, physical properties, mechanical behavior, stability, environmental response, and development of new metallic and ceramic systems. New evidence about directional solidification in terms of temperature gradients is presented along with solidification rates for successful formation of in-situ composite structures. Much is learned about the factors that control structure in directionally solidified eutectic alloys and the relationship of properties to structure, especially the change in properties as a function of operating environment. Less progress is achieved in the area of physical properties than in the area of mechanical properties. Individual items are announced in this issue.

Jackson, M. R.↗
NASA NTRS1976

Structure-property relationships in eutectic composites

The preparation of a composite material of eutectic composition directly from the molten state is investigated. The manufacture of eutectic composites by unidirectional solidification is reviewed, and it is shown how two-phase composite structures of given relative volume fraction can be produced with a range of particle sizes. Crystallographic relationships and the thermal stability of interfaces in controlled eutectic structures are examined, the mechanical behavior of aligned eutectic microstructures is discussed, and characteristics of eutectic composites having mechanical properties of engineering significance are evaluated. Specific properties of the Ni-Nb eutectic alloy are reviewed to demonstrate the effect of structure control (through directional solidification) on the mechanical response of a eutectic composite. It is noted that unidirectionally solidified eutectic composites possess highly aligned and thermally stable microstructures and also exhibit excellent combinations of strength and ductility to very high temperature levels.

Hertzberg, R. W.↗
NASA NTRS1975

Hot tensile properties and deformation response of a gamma/Ni/-gamma prime/Ni3Al/-delta/Ni3Nb/ eutectic composite

Three distinct regions of tensile, deformation and fracture behavior were observed in a 2.5 wt. per cent Al gamma/gamma prime-delta eutectic alloy as the testing temperature was varied. The major finding was an extraordinary ductility maximum at about 550 C. It was shown that this phenomenon is caused by the deflection of transverse cracks at the eutectic grain boundaries when yielding occurs. This delamination between eutectics grains caused by fracture of a gamma prime eutectic grain boundary film leads to a distinctly different 'wood-like' fracture surface morphology. Above 690 C to 926 C, yield and tensile strength values decrease while ductility increase slightly. Cooperative twinning of both phases develops giving rise to block-like deformation of the microstructure quite in parallel to the behavior observed previously in the gamma-delta system.

Bertorello, H. R.↗
NASA NTRS1975

Fatigue crack propagation behavior of the Ni-Ni3Cb eutectic composite

The experimental procedures used in the investigation are considered, taking into account solidification and heat treatment, fatigue testing, questions of test specimen and loading fixture design verification, metallographic techniques, and electron microscopy techniques. Attention is given to the characteristics of the microstructure, aspects of fatigue crack propagation (FCP) in the Ni-Ni3Nb composite, the effect of test variables on FCP, the effect of metallurgical variables on FCP, and fatigue fracture mechanisms. Fractographic and metallographic observations are discussed.

Mills, W. J.↗
NASA NTRS1974

Interfaces in directionally solidified eutectics

Consideration of the interface between the phases in directionally solidified eutectic structures with respect to its morphology, crystallography, stability, and overall response to internal and external stress fields. Yielding behavior in such eutectic structures is shown to be controlled by several possible mechanisms. Two that can be related to the interface in directionally-solidified eutectic alloys are: (1) the interaction of slip dislocations with interface dislocations of the semicoherent boundaries, and (2) restrictions of allowable deformation mechanisms in two contiguous phases due to orientation effects. Evidence found thus far for elastic-plastic eutectic composites indicates that interfaces are capable of diverting fatigue cracks parallel to the loading axis.

Hertzberg, R. W.↗
NASA NTRS1967

Fatigue fracture surface appearance.

Fatigue fracture surface macroscopic and microscopic appearance as affected by prevailing stress intensity conditions at moving crack tip

STRAIN FATIGUE↗