Hybrid physics-AI outperforms numerical weather prediction for extreme precipitation nowcasting
Not provided.
Engineering topics
Publications and source records attributed to Hicks, Michael.
Not provided.
We present VOQC, the first verified optimizer for quantum circuits, written using the Coq proof assistant. Quantum circuits are expressed as programs in a simple, low-level language called SQIR, a small quantum intermediate representation, which is deeply embedded in Coq. Optimizations and other transformations are expressed as Coq functions, which are proved correct with respect to a semantics of SQIR programs. SQIR programs denote complex-valued matrices, as is standard in quantum computation, but we treat matrices symbolically to reason about programs that use an arbitrary number of quantum bits. SQIR’s careful design and our provided automation make it possible to write and verify a broad range of optimizations in VOQC, including full-circuit transformations from cutting-edge optimizers.
n-Propylbenzene (PB, C9H12, 432K boiling point) is important as a constituent in surrogates for some transportation fuels but little is understood about its droplet burning characteristics. We present an experimental and numerical study of a fuel droplet burning under conditions where the sole means of gas transport is fuel evaporation at the droplet surface thereby creating a one-dimensional gas transport that is amenable to detailed numerical modeling. The one-dimensional gas transport that results is amenable to detailed numerical modeling. Initial droplet diameters (Do) ranged from 0.3 mm to about 5 mm to better understand the mechanisms that control burning over such a wide range of Do. For Do < 1 mm droplets were burned while anchored to 14 m SiC fibers within a sealed container in free-fall during which time the droplets were ignited by spark discharge and the burning process recorded by video cameras. Larger and free-floating droplets were studied in the spaced-based platform of the orbiting International Space Station for Do > 1.0 mm which provided unlimited times for experimental observation. Measurements of droplet, flame and soot shell diameters were made and are discussed in the presentation. The experimental results showed formation of optically thick soot clouds developing during burning that required a robust image analysis algorithm to enable measurement of droplet diameter. The measured droplet diameters were well predicted by a numerical model that included soot formation, a PB kinetic mechanism comprising 576 species and 27369 reactions, unsteady gas and liquid transport, variable properties and radiative transport. Flame diameters showed more variability compared to the simulations, depending on how the flame was defined (peak gas temperature and OH concentration). Droplets burned slower as Do was increased and the PB sooting propensity increased with Do. Flame extinction was observed for Do > 3.3 mm indicating a strong effect of radiation as Do was increased compared to the smaller droplet diameters examined where extinction was not experimentally observed. For the largest droplets examined the possibility that the observed extinction is indicative of a transition to cool flame burning is still under investigation.
Quantum computing technology may soon deliver revolutionary improvements in algorithmic performance, but it is useful only if computed answers are correct. While hardware-level decoherence errors have garnered significant attention, a less recognized obstacle to correctness is that of human programming errors—“bugs.” Techniques familiar to most programmers from the classical domain for avoiding, discovering, and diagnosing bugs do not easily transfer, at scale, to the quantum domain because of its unique characteristics. To address this problem, we have been working to adapt formal methods to quantum programming. With such methods, a programmer writes a mathematical specification alongside the program and semiautomatically proves the program correct with respect to it. The proof’s validity is automatically confirmed—certified—by a “proof assistant.” Formal methods have successfully yielded high-assurance classical software artifacts, and the underlying technology has produced certified proofs of major mathematical theorems. As a demonstration of the feasibility of applying formal methods to quantum programming, we present a formally certified end-to-end implementation of Shor’s prime factorization algorithm, developed as part of a framework for applying the certified approach to general applications. By leveraging our framework, one can significantly reduce the effects of human errors and obtain a high-assurance implementation of large-scale quantum applications in a principled way.
Near-term intermediate scale quantum (NISQ) computers are likely to have very restricted hardware resources, where precisely controllable qubits are expensive, error-prone, and scarce. Programmers of such computers must therefore balance trade-offs among a large number of (potentially heterogeneous) factors specific to the targeted application and quantum hardware. To assist them, we propose Meta Quantum Circuits with Constraints (MQCC), a meta-programming framework for quantum programs. Programmers express their application as a succinct collection of normal quantum circuits stitched together by a set of (manually or automatically) added meta-level choice variables, whose values are constrained according to a programmable set of quantitative optimization criteria. MQCC’s compiler generates the appropriate constraints and solves them via an SMT solver, producing an optimized, runnable program. We showcase a few MQCC’s applications for its generality including an automatic generation of efficient error syndrome extraction schemes for fault-tolerant quantum error correction with heterogeneous qubits and an approach to writing approximate quantum Fourier transformation and quantum phase estimation that smoothly trades off accuracy and resource use. We also illustrate that MQCC can easily encode prior one-off NISQ application designs-–multi-programming (MP), crosstalk mitigation (CM)—as well as a combination of their optimization goals (i.e., a combined MP-CM).
This presentation introduces our research on quantitative soot volume fraction measurements from droplet combustion experiments of sooty fuels.
Experimental observations of two-stage, autoignition characteristics of fiber-supported, n-dodecane fuel droplets under normal gravity are reported for a wide range of ambient temperatures, and pressures varying from 1 atm to 25 atm, which encompasses the fuel critical pressure (~ 18 atm). A high-speed camera is used to obtain backlit images of the autoignition process. During two-stage ignition, a cool-flame front forms below the droplet in the natural convective plume of the fuel vapor originating from the vaporizing droplet, and propagates upward, followed by the formation of a hot-flame kernel that expands rapidly and surrounds the droplet, eventually leading to the classical diffusion flame. Experimentally measured cool, and hot flame formation locations and propagation speeds are presented for varying initial temperatures and pressures. Measured first, and second stage ignition delay times are also reported. The influences of negative temperature coefficient (NTC) regime chemistry on flame starting location, propagation speeds, and ignition delay times are described. The first-stage cool flame characteristics are found to be controlled by both the chemistry, and physical aspects such as droplet evaporation and fuel-oxidizer mixing, while the second-stage hot flame ignition is primarily controlled by chemical kinetics. Further work is currently underway to develop models to quantitatively predict the observed behavior.
This presentation introduce our research on precision measurement of droplet diameter from digital video images of soot-producing fuels
This presentation introduce our research on experiments and analysis of n-Heptane/Iso-butanol mixture droplet combustion.
The daytime planetary boundary layer (PBL) was examined for the Deriving Information on Surface Conditions from Column and Vertically Resolved Observations Relevant to Air Quality (DISCOVER-AQ) Baltimore (Maryland)–Washington, D.C., campaign of July 2011 using PBL height (PBLH) retrievals from aerosol backscatter measurements from ground-based micropulse lidar (MPL), the NASA Langley Research Center airborne High Spectral Resolution Lidar-1 (HSRL-1), and the Cloud–Aerosol Lidar with Orthogonal Polarization (CALIOP) on the Cloud–Aerosol Lidar and Infrared Pathfinder Satellite Observations (CALIPSO) satellite. High-resolution Weather Research and Forecasting (WRF) Model simulations with horizontal grid spacing of 1 km and different combinations of PBL schemes, urban parameterization, and sea surface temperature inputs were evaluated against PBLHs derived from lidars, ozonesondes, and radiosondes. MPL and WRF PBLHs depicted a growing PBL in the morning that reached a peak height by midafternoon. WRF PBLHs calculated from gridded output profiles generally showed more rapid growth and higher peak heights than did the MPLs, and all WRF–lidar differences were dependent on model configuration, PBLH calculation method, and synoptic conditions. At inland locations, WRF simulated an earlier descent of the PBL top in the afternoon relative to the MPL retrievals and radiosonde PBLHs. At Edgewood, Maryland, the influence of the Chesapeake Bay breeze on the PBLH was captured by both the ozonesonde and WRF data but generally not by the MPL PBLH retrievals because of generally weaker gradients in the aerosol backscatter profile and limited normalized relative backscatter data near the top height of the marine layer.
Experimental data and detailed numerical modelling are presented on the burning characteristics of a model gasoline/biofuel mixture consisting of n-heptane and iso-butanol. A droplet burning in an environment that minimises the influence of buoyant and forced convective flows in the standard atmosphere is used to promote one-dimensional gas transport to facilitate numerical modelling of the droplet burning process. The numerical model includes a detailed combustion kinetic mechanism, unsteady gas and liquid transport, multicomponent diffusion inside the droplet, variable properties, and non-luminous radiative heat transfer from the flame. The numerical simulation was validated by experimental measurements in the standard atmosphere which showed good agreement with the evolutions of droplet and flame diameters. The iso-butanol concentration had a strong effect on formation of particulates. Above ~20% (volume) iso-butanol, flame luminosity was significantly diminished anddecreased with increasing iso-butanol concentration, while CO2 emissions as a representative greenhouse gas were not strongly influenced by the iso-butanol loading. The soot shell was located near a 1350 K isotherm for concentrations up to 20% (volume) iso-butanol, suggesting this value as a possible soot inception temperature for the mixture droplet. The combustion rate decreased with increasing iso-butanol concentration which was attributed to iso-butanol's higher liquid density. No evidence of a low temperature burning regime, or of extinction, was found (in experiments and simulations) for the small droplet sizes investigated.
1. Automated computer algorithms have been developed for precision measurements of droplet combustion image sequences. 2. Initial results indicted that a good performance with respect to decane/propylbenzene (which is highly sooting) can be achieved. 3. In continuing work, methods to produce higher precision results are being explored for flame diameter, and the system will self calibrate for each image dataset to a 95% measurement error
The Supercritical Water Mixture (SCWM) experiment conducted on the International Space Station (ISS) is designed to study a salt-water solution in the vicinity of the critical transition with a test cell filled with Na2SO4 (aq) 0.5-w. This salt is a Type II salt which undergoes a dramatic decrease in solubility past waters critical point. The paper discusses the liquid-vapor-salt distribution in the test cell for subcritical, trans-critical, and supercritical regimes. In 0-g, the vapor-liquid interface manifests itself by the presence of a large single vapor bubble that is flattened between the two windows. In contrast with pure water, the vapor bubble remains centered in the test cell and is stable for temperatures up to Tc - 50 mK. The processes leading to critical transition during heat-up, as marked by the break-up of the vapor bubble, depends on the applied heating rate. For temperature ramps 1 mKmin, the bubble interface begins to breakup with the formation of a large number of smaller bubbles. For larger temperature ramps (10mKmin), temperature gradients arise in the cell pushing the bubble toward a window surface. As the critical threshold is crossed small variations in cell temperature ( 1 mK) cause an observable spatial variation in density. However, this spatial variation is not discernible as the temperature is increased further into the supercritical regime. The salt precipitation in the vicinity of the critical crossing appears to be heterogeneous in nature with precipitates observable on the cell windows. Direct imaging as well as light scattering indicate a hexagonal structure of the precipitated salt crystals in the near critical regime. The salt deposition is not fully reversible as the temperature is reduced due to window corrosion effects which traps some of the precipitated salt. Critical temperatures as high as 1.9 K above the value for pure water (647.25 K) have been measured. Finally, results on the critical transition phenomena in the presence of an imposed temperature gradient, demonstrating the remarkable stability of the central bubble, are also presented.
On 11 May 2010, an elevated temperature inversion associated with an approaching warm front produced two melting layers simultaneously, which resulted in two distinct bright bands as viewed from the ER-2 Doppler radar system, a vertically pointing, coherent X band radar located in Greenbelt, MD. Due to the high temporal resolution of this radar system, an increase in altitude of the melting layer of approximately 1.2 km in the time span of 4 min was captured. The double bright band feature remained evident for approximately 17 min, until the lower atmosphere warmed enough to dissipate the lower melting layer. This case shows the relatively rapid evolution of freezing levels in response to an advancing warm front over a 2 h time period and the descent of an elevated warm air mass with time. Although observations of double bright bands are somewhat rare, the ability to identify this phenomenon is important for rainfall estimation from spaceborne sensors because algorithms employing the restriction of a radar bright band to a constant height, especially when sampling across frontal systems, will limit the ability to accurately estimate rainfall.
The effects of gravity on the fluid mechanics of supercritical water jets are being studied at NASA to develop a better understanding of flow behaviors for purposes of advancing supercritical water oxidation (SCWO) technologies for applications in reduced gravity environments. These studies provide guidance for the development of future SCWO experiments in new experimental platforms that will extend the current operational range of the DECLIC (Device for the Study of Critical Liquids and Crystallization) Facility on board the International Space Station (ISS). The hydrodynamics of supercritical fluid jets is one of the basic unit processes of a SCWO reactor. These hydrodynamics are often complicated by significant changes in the thermo-physical properties that govern flow behavior (e.g., viscosity, thermal conductivity, specific heat, compressibility, etc), particularly when fluids transition from sub-critical to supercritical conditions. Experiments were conducted in a 150 ml reactor cell under constant pressure with water injections at various flow rates. Flow configurations included supercritical jets injected into either sub-critical or supercritical water. Profound gravitational influences were observed, particularly in the transition to turbulence, for the flow conditions under study. These results will be presented and the parameters of the flow that control jet behavior will be examined and discussed.
Off-road concerns are related to the effects of shock and vibration and air quality on fuel cell power requirements. Mechanical stresses on differing material makeup and mass distribution within the system may render some components susceptible to impulse trauma while others may show adverse effects from harmonic disturbances or broad band mechanical agitation. One of the recognized challenges in fuel cell systems air purification is in providing a highly efficient particulate and chemical filter with minimal pressure drop. PEM integrators do not want additional parasitic loads added to the system as compensation for a highly efficient yet highly restrictive filter. Additionally, there is challenge in integrating multiple functions into a single air intake module tasked with effectively filtering high dust loads, diesel soot, pesticides, ammonias, and other anticipated off-road contaminants. This project has investigated both off-road associated issues cumulating in the prototype build and testing of two light duty off-road vehicles with integrated fuel cell power plant systems.
The U.S. modules of the International Space Station use gaseous CO2 as the fire extinguishing agent. This was selected as a result of extensive experience with CO2 as a fire suppressant in terrestrial applications, trade studies on various suppressants, and experiments. The selection of fire suppressants and suppression strategies for NASA s Lunar and Martian exploration missions will be based on the same studies and normal-gravity data unless reduced gravity fire suppression data is obtained. In this study, the suppressant agent concentrations required to extinguish a flame in low velocity convective flows within the 20-sec of low gravity on the KC-135 aircraft were investigated. Suppressant gas mixtures of CO2, N2, and He with the balance being oxygen/nitrogen mixtures with either 21% or 25% O2 were used to suppress flames on a 19-mm diameter PMMA cylinder in reduced gravity. For each of the suppressant mixtures, limiting concentrations were established that would extinguish the flame at any velocity. Similarly, concentrations were established that would not extinguish the flame. The limiting concentrations were generally consistent with previous studies but did suggest that geometry had an effect on the limiting conditions. Between the extinction and non-extinction limits, the suppression characteristics depended on the extinguishing agent, flow velocity, and O2 concentration. The limiting velocity data from the CO2, He, and N2 suppressants were well correlated using an effective mixture enthalpy per mole of O2, indicating that all act via O2 displacement and cooling mechanisms. In reduced gravity, the agent concentration required to suppress the flames increased as the velocity increased, up to approximately 10 cm/s (the maximum velocity evaluated in this experiment). The effective enthalpy required to extinguish flames at velocities of 10 cm/s is approximately the same as the concentrations in normal gravity. A computational study is underway to further evaluate these findings.