Search NASA⌕ Search

Engineering topics

Higa, W. H.

Publications and source records attributed to Higa, W. H..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1984

Centrifugal-reciprocating compressor

A centrifugal compressor is described which includes at least one pair of cylinders arranged in coaxial alignment and supported for angular displacement about a common axis of rotation normally disecting a common longitudinal axis of symmetry for the cylinders. The cylinders are characterized by ported closures located at the mutually remote ends thereof through which the cylinders are charged and discharged, and a pair of piston heads seated within the cylinders and supported for floating displacement in compressive strokes in response to unidirectional angular displacement imparted to the cylinders.

Higa, W. H.↗
NASA NTRS1980

On the characteristics of centrifugal-reciprocating machines

A method of compressing helium gas for cryogenic coolers is presented which uses centrifugal force to reduce the forces on the connecting rod and crankshaft in the usual reciprocating compressor. This is achieved by rotating the piston-cylinder assembly at a speed sufficient for the centrifugal force on the piston to overcome the compressional force due to the working fluid. The rotating assembly is dynamically braked in order to recharge the working space with fluid. The intake stroke consists of decelerating the rotating piston-cylinder assembly and the exhaust stroke consists of accelerating the assembly.

Higa, W. H.↗
NASA NTRS1976

Stirling cycle engine and refrigeration systems

A Stirling cycle heat engine is disclosed in which displacer motion is controlled as a function of the working fluid pressure P sub 1 and a substantially constant pressure P sub 0. The heat engine includes an auxiliary chamber at the constant pressure P sub 0. An end surface of a displacer piston is disposed in the auxiliary chamber. During the compression portion of the engine cycle when P sub 1 rises above P sub 0 the displacer forces the working fluid to pass from the cold chamber to the hot chamber of the engine. During the expansion portion of the engine cycle the heated working fluid in the hot chamber does work by pushing down on the engine's drive piston. As the working fluid pressure P sub 1 drops below P sub 0 the displacer forces most of the working fluid in the hot chamber to pass through the regenerator to the cold chamber. The engine is easily combinable with a refrigeration section to provide a refrigeration system in which the engine's single drive piston serves both the engine and the refrigeration section.

Higa, W. H.↗
NASA NTRS1975

Simplified heat engine

In Sterling-cycle heat engine, pneumatic system is used to drive displacer/regenerator, eliminating mechanical linkages and valves.

Higa, W. H.↗
NASA NTRS1975

Performance of a solar-thermal collector

Possible means of achieving the technology required for field application of solar thermal power systems are discussed. Simplifications in construction techniques as well as in measurement techniques for parabolic trough collectors are described. Actual measurement data is also given.

Higa, W. H.↗
NASA NTRS1975

Spurious signals generated by electron tunneling on large reflector antennas

Large reflector antennas are currently fabricated by assembling a large number of small light aluminum panels onto a superstructure. A large number of aluminum-to-aluminum joints are inherently exposed to RF radiation on such an antenna. It is shown in this paper that the natural oxide layer on aluminum is of the correct thickness to permit electron tunneling through the Al-Al2O3-Al junctions. The nonlinearity due to the junctions then generates spurious signals when these antennas are used for simultaneous transmission and reception of signals at different frequencies. Moreover, the large number of junctions (rivets) on an antenna can combine to produce serious interference in these diplexed systems.

Higa, W. H.↗
NASA NTRS1972

Time synchronization via lunar radar.

The advent of round-trip radar measurements has permitted the determination of the ranges to the nearby planets with greater precision than was previously possible. When the distances to the planets are known with high precision, the propagation delay for electromagnetic waves reflected by the planets may be calculated and used to synchronize remotely located clocks. Details basic to the operation of a lunar radar indicate a capability for clock synchronization to plus or minus 20 microsec. One of the design goals for this system was to achieve a simple semiautomatic receiver for remotely located tracking stations. The lunar radar system is in operational use for deep space tracking at Jet Propulsion Laboratory and synchronizes five world-wide tracking stations with a master clock at Goldstone, Calif. Computers are programmed to correct the Goldstone transmissions for transit time delay and Doppler shifts so as to be received on time at the tracking stations; this dictates that only one station can be synchronized at a given time period and that the moon must be simultaneously visible to both the transmitter and receiver for a minimum time of 10 min.-

Higa, W. H.↗
NASA NTRS1967

Highly stable microwave delay line

TWM /Traveling Wave Master/ comb structure serves as a highly stable microwave delay line for determining the short-term stability of the hydrogen maser frequency standards used in the deep space network. Cryogenic cooling is used to minimize signal attenuation and thermal noise.

Higa, W. H.↗
NASA NTRS1967

Improved cryogenic refrigeration system

Two-position shuttle valve simplifies valving arrangement and crank-shaft configuration in gas-balancing and Stirling-cycle refrigeration systems used to produce temperatures below 173 degrees K. It connects the displacer and regenerator alternately to the supply line or the return line of the compressor, and establishes constant pressure on the drive piston.

Higa, W. H.↗