Search NASASearch

Engineering topics

Hill, J. M.

Publications and source records attributed to Hill, J. M..

At least 19 records

The HOSTS Survey-Exozodiacal Dust Measurements for 30 Stars

The Hunt for Observable Signatures of Terrestrial Systems survey searches for dust near the habitable zones (HZs) around nearby, bright main-sequence stars. We use nulling interferometry in the N band to suppress the bright stellar light and to probe for low levels of HZ dust around the 30 stars observed so far. Our overall detection rate is 18%, including four new detections, among which are the first three around Sun-like stars and the first two around stars without any previously known circumstellar dust. The inferred occurrence rates are comparable for early-type and Sun-like stars, but decrease from 60(sup +16)(sub -21)% for stars with previously detected cold dust to 8(sup +10)(sub -3)% for stars without such excess, confirming earlier results at higher sensitivity. For completed observations on individual stars, our sensitivity is five to ten times better than previous results. Assuming a lognormal excess luminosity function, we put upper limits on the median HZ dust level of 13 zodis (95% confidence) for a sample of stars without cold dust and of 26 zodis when focusing on Sun-like stars without cold dust. However, our data suggest that a more complex luminosity function may be more appropriate. For stars without detectable Large Binocular Telescope Interferometer (LBTI) excess, our upper limits are almost reduced by a factor of two, demonstrating the strength of LBTI target vetting for future exo-Earth imaging missions. Our statistics are limited so far, and extending the survey is critical to informing the design of future exo-Earth imaging surveys.

The Hunt for Observable Signatures of Terrestrial

Simultaneous Water Vapor and Dry Air Optical Path Length Measurements and Compensation with the Large Binocular Telescope Interferometer

The Large Binocular Telescope Interferometer uses a near-infrared camera to measure the optical path length variations between the two AO-corrected apertures and provide high-angular resolution observations for all its science channels (1.5-13 microns). There is however a wavelength dependent component to the atmospheric turbulence, which can introduce optical path length errors when observing at a wavelength different from that of the fringe sensing camera. Water vapor in particular is highly dispersive and its effect must be taken into account for high-precision infrared interferometric observations as described previously for VLTI/MIDI or the Keck Interferometer Nuller. In this paper, we describe the new sensing approach that has been developed at the LBT to measure and monitor the optical path length fluctuations due to dry air and water vapor separately. After reviewing the current performance of the system for dry air seeing compensation, we present simultaneous H-, K-, and N-band observations that illustrate the feasibility of our feed forward approach to stabilize the path length fluctuations seen by the LBTI nuller uses a near-infrared camera to measure the optical path length variations between the two AO-corrected apertures and provide high-angular resolution observations for all its science channels (1.5-13 microns). There is however a wavelength dependent component to the atmospheric turbulence, which can introduce optical path length errors when observing at a wavelength different from that of the fringe sensing camera. Water vapor in particular is highly dispersive and its effect must be taken into account for high-precision infrared interferometric observations as described previously for VLTI MIDI or the Keck Interferometer Nuller. In this paper, we describe the new sensing approach that has been developed at the LBT to measure and monitor the optical path length fluctuations due to dry air and water vapor separately. After reviewing the current performance of the system for dry air seeing compensation, we present simultaneous H-, K-, and N-band observations that illustrate the feasibility of our feed forward approach to stabilize the path length fluctuations seen by the LBTI nuller.

which can introduce optical path length errors whe

Nulling Data Reduction and On-Sky Performance of the Large Binocular Telescope Interferometer

The Large Binocular Telescope Interferometer (LBTI) is a versatile instrument designed for high angular resolution and high-contrast infrared imaging (1.5-13 micrometers). In this paper, we focus on the mid-infrared (8-13 micrometers) nulling mode and present its theory of operation, data reduction, and on-sky performance as of the end of the commissioning phase in 2015 March. With an interferometric baseline of 14.4 m, the LBTI nuller is specifically tuned to resolve the habitable zone of nearby main-sequence stars, where warm exozodiacal dust emission peaks. Measuring the exozodi luminosity function of nearby main-sequence stars is a key milestone to prepare for future exo-Earth direct imaging instruments. Thanks to recent progress in wavefront control and phase stabilization, as well as in data reduction techniques, the LBTI demonstrated in 2015 February a calibrated null accuracy of 0.05% over a 3 hr long observing sequence on the bright nearby A3V star Beta Leo. This is equivalent to an exozodiacal disk density of 15-30 zodi for a Sun-like star located at 10 pc, depending on the adopted disk model. This result sets a new record for high-contrast mid-infrared interferometric imaging and opens a new window on the study of planetary systems.

circumstellar matter aEuro" techniques: interferom

Co-Phasing the Large Binocular Telescope:

The Large Binocular Telescope Interferometer is a NASA-funded nulling and imaging instrument designed to coherently combine the two 8.4-m primary mirrors of the LBT for high-sensitivity, high-contrast, and high-resolution infrared imaging (1.5-13 micrometer). PHASECam is LBTI's near-infrared camera used to measure tip-tilt and phase variations between the two AO-corrected apertures and provide high-angular resolution observations. We report on the status of the system and describe its on-sky performance measured during the first semester of 2014. With a spatial resolution equivalent to that of a 22.8-meter telescope and the light-gathering power of single 11.8-meter mirror, the co-phased LBT can be considered to be a forerunner of the next-generation extremely large telescopes (ELT).

LBT

The Gray Needle: Large Grains in the HD 15115 Debris Disk from LBT*/PISCES/K s and LBTIi+/LMIRcam/L(prime) Adaptive Optics Imaging

We present diffraction-limited K s band and L(prime) adaptive optics images of the edge-on debris disk around the nearby F2 star HD 15115, obtained with a single 8.4 m primary mirror at the Large Binocular Telescope. At the Ks band, the disk is detected at signal-to-noise per resolution element (SNRE) approx. 3-8 from approx. 1 to 2".5 (45-113 AU) on the western side and from approx. 1". 2 to 2".1 (63-90 AU) on the east. At L the disk is detected at SNRE approx. 2.5 from approx. 1 to 1".45 (45-90 AU) on both sides, implying more symmetric disk structure at 3.8 micrometers. At both wavelengths the disk has a bow-like shape and is offset from the star to the north by a few AU. A surface brightness asymmetry exists between the two sides of the disk at the Ks band, but not at L(prime). The surface brightness at the K s band declines inside 1"(approx. 45 AU), which may be indicative of a gap in the disk near 1".The K s − L(prime) disk color, after removal of the stellar color, is mostly gray for both sides of the disk. This suggests that scattered light is coming from large dust grains, with 3-10 micrometers sized grains on the east side and 1-10 micrometers dust grains on the west. This may suggest that the west side is composed of smaller dust grains than the east side, which would support the interpretation that the disk is being dynamically affected by interactions with the local interstellar medium.

signal-to-noise

The dynamics of Abell 2634

We have amassed a large sample of velocity data for the cluster of galaxies Abell 2634 which contains the wide-angle tail (WAT) radio source 3C 465. Robust indicators of location and scale and their confidence intervals are used to determine if the cD galaxy, containing the WAT, has a significant peculiar motion. We find a cD peculiar radial velocity of 219 plus or minus 98 km s(exp -1). Further dynamical analyses, including substructure and normality tests, suggest that A 2634 is an unrelaxed cluster whose radio source structure may be bent by the turbulent gas of a recent cluster-subcluster merger.

Pinkney, J.

A study of HII regions in spiral galaxies using multiobject spectroscopy

Multiobject spectroscopy results of HII regions in nearby late-type spiral galaxies are given. Results include excitation measurements, log ((O III)/H beta), for 81 regions in M 101, 30 regions in NGC 2403, and 13 regions in M 51. Researchers conclude that late-type spirals can be classified into two distinct populations, examine possible causes of this division, and derive metallicity gradients for these galaxies. M 51 appears to have an anomalously shallow abundance gradient.

Zaritsky, Dennis

A data reduction package for multiple object spectroscopy

Experience with fiber-optic spectrometers has demonstrated improvements in observing efficiency for clusters of 30 or more objects that must in turn be matched by data reduction capability increases. The Medusa Automatic Reduction System reduces data generated by multiobject spectrometers in the form of two-dimensional images containing 44 to 66 individual spectra, using both software and hardware improvements to efficiently extract the one-dimensional spectra. Attention is given to the ridge-finding algorithm for automatic location of the spectra in the CCD frame. A simultaneous extraction of calibration frames allows an automatic wavelength calibration routine to determine dispersion curves, and both line measurements and cross-correlation techniques are used to determine galaxy redshifts.

Hill, J. M.

Steps toward 8m honeycomb mirror blanks. III - 1.8m honeycomb sandwich blanks cast from borosilicate glass

The design, fabrication techniques, and equipment used for producing two 1.8-m honeycomb sandwich blanks, eventually leading to production of 8-m blanks, are reported. The procedure employed 85 cast hexagonal tiles at the bottom section, affixed against flotation by SiC bolts. The two plano concave mirrors are 1.83 m thick, weight 500 kg, and are each designed for 19 supports of astatic-lever type. Both blanks are of high quality and with an adequately low bubble content; one is to be figured to high-precision 0.25-arcsecond images, and is to be tested on the Multiple Mirror Telescope. Construction of a spin-casting facility based on the same principle is being planned for test-fabricating spin-cast mirrors on a smaller scale.

Angel, J. R. P.

Steps toward 8m honeycomb mirrors IV - Some aspects of design and fabrication

The tolerances in glass homogeneity, thermal control, and support of the blank, necessary to meet the requirements of telescopes in the best ground-based sites, are defined for a hypothetical 8-m honeycomb mirror spin-casting facility. Homogeneity in expansion coefficient of 10 to the -8th/C and thermal equilibration to 0.1 C are estimated. Laboratory measurements show that both can be met by a ventilated honeycomb of borosilicate or similar glass. Adequate resistance to wind pressure and buffeting can be achieved by an axial support that responds to pressure on the three defining points. Annealing of the blank at the peak cooling rate of 20 C/day will take about six weeks, leading to a temporary stress of 15 kg/sq cm.

Angel, J. R. P.

Optical matching for fiber optic spectroscopy

Single silica fibers of the type developed for communications are useful in the design of astronomical spectrographs. They can be used to couple light from many objects over a wide field to a single spectrograph, or to eliminate wavelength errors from image motion and gravitational flexure. For many applications it will be advantageous to use small lenses to make the most efficient coupling into and out of a fiber. If the telescope pupil is imaged on the fiber core, an efficient coupling can be made that preserves image size over a certain range. This method is demonstrated by a laboratory test using sapphire spheres as coupling lenses.

Hill, J. M.

Steps toward 8 m honeycomb mirror blanks. II - Experiments with waffleplate and honeycomb casting

A technique for fabricating large low-cost light-weight borosilicate-glass mirrors for ground and space-based astronomy is described. This technique involves the remelting of glass into complex molds for vacuum-formed ceramic fiber and is used to cast in one piece either waffleplate or full honeycomb sandwich blanks. The construction of molds and the cycle for melting and annealing are described in detail. A 1.1-m square blank with a 22.4-cm-thick face and 1.6-cm ribs, 15-cm deep on 15-cm squares, has been cast, and a 1.8-m circular blank of full honeycomb construction is scheduled for production. The casting of blanks of up to 8-m in diameter is anticipated, with densities of 200 kg/sq m (like that of the ST mirror) being typical of casting.

Hill, J. M.

Fiber optics for astronomical spectroscopy - The Medusa Spectrograph

An instrument has been built to obtain simultaneous spectra of 32 objects in the field of view of the Steward Observatory 2.3 m telescope. Short lengths of optical fiber are used to bring light from galaxy images at the focus of the telescope into a line at the spectrograph slit. This multi-fiber aperture plate instrument has been dubbed the Medusa Spectrograph. The Medusa is now producing spectra of about 100 galaxies per clear night. An optimized version of the instrument called the MX Spectrometer is being constructed to record spectra at a higher rate. This new instrument will have remotely positioned fibers under computer control. A Charge Coupled Device will be used as the spectrograph detector to allow sky subtraction, give increased dynamic range and provide more accurate wavelength calibration. Transmission characteristics of some commercial fibers are discussed, and the microlens optics used to match the telescope and the spectrograph to the fibers to avoid focal ratio degradation are described.

Hill, J. M.

Medusa spectroscopy of A400, A576, A1767, and A2124

Galaxy velocity data taken with the Steward Observatory multiple aperture fiber optic spectrograph are presented for four Abell clusters. The root-mean-square external errors in these velocities are about 100 km/s; accuracy which compares favorably with that obtained from single-object observations. It is expected that the recent adoption of a CCD detector should decrease external errors to about 50 km/s. All four of the clusters observed are known X-ray sources and the present data agree well with empirically derived velocity dispersion-X-ray luminosity relations for clusters of galaxies. Abell 400 is interesting in this regard, since both its X-ray luminosity and its velocity dispersion are quite small. Such objects are particularly important in determining the slope of the velocity dispersion-X-ray luminosity relation. The large microwave decrement observed in A576 was initially interpreted as due to Compton scattering of the microwave background by the X-ray-emitting intracluster gas. White and Silk have presented Einstein X-ray data which indicate that A576 contains too little gas to produce the observed microwave decrement by Compton scattering. The velocity dispersion obtained here for 47 members of this cluster strengthens their conclusion.

Hintzen, P.

Honeycomb mirrors of borosilicate glass - Current results and plans for 7-8m diameter

The making of large astronomical mirrors with borosilicate glass honeycomb structure is discussed. Particular attention is given to a single casting technique for making borosilicate honeycomb mirror blanks up to 7 meters in diameter. Current work on the development of this technique involves the casting of blanks 60 cm in diameter which have the full thickness (33 cm), cell size (15 cm), and faceplate thickness (2.5 cm) needed for a 1.8-m mirror.

Angel, J. R. P.

Honeycomb mirrors of borosilicate glass

The fabrication of different types of honeycomb mirrors with various kinds of borosilicate glass is discussed. Borosilicate glass is much less expensive to make than zero expansion glass, and can be used for ground-based applications. A mirror 60 cm in diameter made with a slotted strut or egg-crate honeycomb of 6 mm polished Pyrex plate is shown. The faceplates are 12 mm thick, laminated from the same 6 mm sheet. The result of an interferometric test is shown, with residual errors of about wavelength/8 RMS. An alternative fabrication technique for very large mirrors which require high quality bonds between separate sheets of thick Pyrex is described. The result of a recent test casting of a 60 cm honeycomb structure made in a mold with towers 14 cm square and 6 mm gaps between is shown, and methods to cast an entire mirror in one operation are discussed.

Angel, J. R. P.

Manufacture of large glass honeycomb mirrors

The problem of making very large glass mirrors for astronomical telescopes is examined, and the advantages of honeycomb mirrors made of borosilicate glass are discussed. Thermal gradients in the glass that degrade the figure of thick borosilicate mirrors during use can be largely eliminated in a honeycomb structure by internal ventilation (in air) or careful control of the radiation environment (in space). It is expected that ground-based telescopes with honeycomb mirrors will give better images than those with solid mirrors. Materials, techniques, and the experience that has been gained making trial mirrors and test castings as part of a program to develop 8-10-m-diameter lightweight mirrors are discussed.

Angel, J. R. P.

Multiple object fiber optic spectroscopy

The Steward Observatory of the University of Arizona employs short optical fiber lengths to bring light from galaxy images at the 2.3 m telescope's focus to a line along a spectrograph slit, thereby obtaining simultaneous spectra of many objects of the field of view. After describing this instrument, attention is given to the development of an improved version through which efficiency gains will be obtained by remotely positioning the fibers under computer control and by correctly matching fiber outputs to the spectrograph optics. A CCD will replace the presently employed image tube and photographic plate detector system, in order to permit sky subtraction, yield increased dynamic range, and provide more accurate wavelength calibration due to the detector's fixed format.

Hill, J. M.