Frustraum 1100 experimental campaign on the national ignition facility
Not Available
Baker, K. L. (ORCID:0000000152163176)↗
Engineering topics
Hinkel, D. E.
Publications and source records attributed to Hinkel, D. E..
Understanding the deficiency in inertial confinement fusion hohlraum x-ray flux predictions using experiments at the National Ignition Facility
The predicted implosion performance of deuterium-tritium fuel capsules in indirect-drive inertial confinement fusion experiments relies on precise calculations of the x-ray drive in laser-heated cavities (hohlraums). This requires accurate, spectrally dependent simulations of laser to x-ray conversion efficiencies and x-ray absorption losses to the hohlraum wall. A set of National Ignition Facility experiments have identified a cause for the long-standing hohlraum “drive deficit” as the overprediction of gold emission at ~2.5 keV in nonlocal thermodynamic equilibrium coronal plasma regions within the hohlraum. Finally, reducing the emission and absorption opacity in this spectral region by ~20% brings simulations into agreement with measured x-ray fluxes and spectra.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
The impact of low-mode symmetry on inertial fusion energy output in the burning plasma state
Indirect Drive Inertial Confinement Fusion Experiments on the National Ignition Facility (NIF) have achieved a burning plasma state with neutron yields exceeding 170 kJ, roughly 3 times the prior record and a necessary stage for igniting plasmas. The results are achieved despite multiple sources of degradations that lead to high variability in performance. Results shown here, for the first time, include an empirical correction factor for mode-2 asymmetry in the burning plasma regime in addition to previously determined corrections for radiative mix and mode-1. Analysis shows that including these three corrections alone accounts for the measured fusion performance variability in the two highest performing experimental campaigns on the NIF to within error. Here we quantify the performance sensitivity to mode-2 symmetry in the burning plasma regime and apply the results, in the form of an empirical correction to a 1D performance model. Furthermore, we find the sensitivity to mode-2 determined through a series of integrated 2D radiation hydrodynamic simulations to be consistent with the experimentally determined sensitivity only when including alpha-heating.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Design of the first fusion experiment to achieve target energy gain G > 1
Not Available
Kritcher, A. L.↗
Control of low-mode drive asymmetry in an efficient long-pulse low gas-fill density Hohlraum
Laser-driven Hohlraums filled with gas at lower densities (<0.6 mg/cc) have higher efficiency compared to original ≥ 0.96 mg/cc fill because of reduced backscatter losses [Hall et al., Phys. Plasmas 24, 052706 (2017)]. However, using low-density filled Hohlraums with longer drive required for lower adiabat implosions, and hence potentially higher inertial confinement fusion gain designs, has been challenging since the Hohlraum wall blow-off is less tamped, thus altering the laser beam absorption regions and drive symmetry. A series of NIF experiments using optimized pulse shaping, beam pointing, and temporal phasing have demonstrated, through imaging of the Hohlraum and capsule dynamics, that a symmetric implosion using a 14-ns low-adiabat drive pulse {2× longer than high-density-carbon ablator designs using low gas-fill density Hohlraums [Divol et al., Phys. Plasmas 24, 056309 (2017)]} is possible in a low backscatter loss 0.45 mg/cc He-filled Hohlraum. The ingress of the Hohlraum walls was mitigated by revisiting the adiabat-shaped design [Clark et al., Phys. Plasmas 21, 112705 (2014)] that uses a low-power (1 TW) trough that delays the wall expansion. Low-mode P 2 and P 4 drive asymmetry swings caused by the drift of the laser spots were essentially zeroed out by employing temporal beam phasing between cones of beams [Turner et al., Phys. Plasmas 7, 333 (2000)]. So the results also indicate an improved coupling efficiency of ~30% compared to an earlier design using higher density filled Hohlraums and pave the way for revisiting low-adiabat, high convergence drives using CH ablators.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Simulating the filamentation of smoothed laser beams with three-dimensional nonlinear dynamics
In a plasma, the ponderomotive force of an inhomogeneous electromagnetic field expels plasma from regions of high intensity. When a laser propagates through a plasma, this force creates density wells that subsequently modify the index of refraction. The beam refracts and focuses into these wells and may filament. In extreme cases, the laser beam will spray due to increasing angular divergence of the beam. The threshold for ponderomotive self-focusing is well established for isolated laser hotspots or speckles. Here, we define a practical threshold for characterizing the filamentation of thousands of speckles that are found in the focal plane of high-power laser beams spatially smoothed with random phase plates as used at high energy and power laser facilities studying inertial confinement fusion. This threshold is tested against three-dimensional simulations of speckled laser light propagating through plasma. Four metrics are applied to assess filamentation: the fraction of power above five times the average intensity, an effective f-number, the mean-squared perpendicular wavenumber, and the fraction of rarefied density with deviation from the initial density exceeding | δn/ n| = 0.1. The speckled beams studied are generated by random phase plates, both with and without additional polarization smoothing, in a parameter regime of relevance to indirect drive experiments. While filamentation has been discussed extensively in the literature, we believe this to be the first published simulation study with three-dimensional nonlinear hydrodynamics that addresses the onset threshold of ponderomotive filamentation and establishes the lengths and time scales necessary to reach a statistical steady state.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Design of an inertial fusion experiment exceeding the Lawson criterion for ignition
Not Available
Kritcher, A. L.↗
Experimental achievement and signatures of ignition at the National Ignition Facility
An inertial fusion implosion on the National Ignition Facility, conducted on August 8, 2021 (N210808), recently produced more than a megajoule of fusion yield and passed Lawson's criterion for ignition [Phys. Rev. Lett. 129, 075001 (2022)]. Here we describe the experimental improvements that enabled N210808 and present the first experimental measurements from an igniting plasma in the laboratory. Ignition metrics like the product of hot-spot energy and pressure squared, in the absence of self-heating, increased by ~ 35%, leading to record values and an enhancement from previous experiments in the hot-spot energy (~ 3×), pressure (~ 2×), and mass (~ 2×). These results are consistent with self-heating dominating other power balance terms. The burn rate increases by an order of magnitude after peak compression, and the hot-spot conditions show clear evidence for burn propagation into the dense fuel surrounding the hot spot. These novel dynamics and thermodynamic properties have never been observed on prior inertial fusion experiments.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Design of inertial fusion implosions reaching the burning plasma regime
One of the last remaining milestones in fusion research before reaching ignition is creating a burning plasma state, where alpha particles from deuterium-tritium (DT) fusion reactions redeposit their energy as the dominant source of heating in the plasma. The indirect-drive inertial confinement fusion approach at the National Ignition Facility (NIF) uses a laser-generated radiation cavity (hohlraum) to spherically implode DT fuel to high temperatures and densities in a central ”hot spot”. Here, we deliver more energy to the hot spot than ever before, while maintaining the extreme pressures required for inertial confinement, by increasing the size of the implosion compared to previous experiments. We develop more efficient hohlraums, to drive these larger implosions within NIF’s current laser energy and power capability and control symmetry by moving energy between laser beams and by changing the shape of the hohlraum. These designs resulted in record fusion powers of 1.5 petawatts, greater than the input power of the laser, and 170 kJ of fusion energy. Radiation hydrodynamics simulations show alpha particle heating as the dominant term in the hot spot energy balance, e.g. a burning plasma state. This work is expected to motivate future studies of burning plasmas and improve predictive capability by providing a benchmark for modeling used to understand the proximity to ignition.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Burning plasma achieved in inertial fusion
The achievement of obtaining a burning plasma is a critical step toward self-sustaining fusion energy. A burning plasma is a fusion plasma where the alpha-particles created by the deuterium-tritium (DT) fusion reactions are the primary source of heating in the plasma, which is necessary to sustain and propagate the fusion reaction to enable high energy gain. After decades of fusion research, a burning plasma state has finally been achieved. Herein, we report upon the first burning-plasma experiments; this state was achieved using a strategy to increase the capsule spatial scale via two different implosion concepts, on the US National Ignition Facility. These experiments show energies from self-heating in excess of the mechanical work injected into the implosions satisfying several burning plasma metrics, the last experiment additionally shows that the fusion self-heating is greater than losses from radiation and heat conduction. These experiments triple the fusion yield performance and show significantly higher yield amplification from self-heating than prior results; remaining degradations can be reduced for even higher fusion performance.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Design of inertial fusion implosions reaching the burning plasma regime
Abstract In a burning plasma state 1–7 , alpha particles from deuterium–tritium fusion reactions redeposit their energy and are the dominant source of heating. This state has recently been achieved at the US National Ignition Facility 8 using indirect-drive inertial-confinement fusion. Our experiments use a laser-generated radiation-filled cavity (a hohlraum) to spherically implode capsules containing deuterium and tritium fuel in a central hot spot where the fusion reactions occur. We have developed more efficient hohlraums to implode larger fusion targets compared with previous experiments 9,10 . This delivered more energy to the hot spot, whereas other parameters were optimized to maintain the high pressures required for inertial-confinement fusion. We also report improvements in implosion symmetry control by moving energy between the laser beams 11–16 and designing advanced hohlraum geometry 17 that allows for these larger implosions to be driven at the present laser energy and power capability of the National Ignition Facility. These design changes resulted in fusion powers of 1.5 petawatts, greater than the input power of the laser, and 170 kJ of fusion energy 18,19 . Radiation hydrodynamics simulations 20,21 show energy deposition by alpha particles as the dominant term in the hot-spot energy balance, indicative of a burning plasma state.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Burning plasma achieved in inertial fusion
Obtaining a burning plasma is a critical step towards self-sustaining fusion energy. A burning plasma is one in which the fusion reactions themselves are the primary source of heating in the plasma, which is necessary to sustain and propagate the burn, enabling high energy gain. After decades of fusion research, here we achieve a burning-plasma state in the laboratory. These experiments were conducted at the US National Ignition Facility, a laser facility delivering up to 1.9 megajoules of energy in pulses with peak powers up to 500 terawatts. We use the lasers to generate X-rays in a radiation cavity to indirectly drive a fuel-containing capsule via the X-ray ablation pressure, which results in the implosion process compressing and heating the fuel via mechanical work. The burning-plasma state was created using a strategy to increase the spatial scale of the capsule through two different implosion concepts. These experiments show fusion self-heating in excess of the mechanical work injected into the implosions, satisfying several burning-plasma metrics. Additionally, we describe a subset of experiments that appear to have crossed the static self-heating boundary, where fusion heating surpasses the energy losses from radiation and conduction. These results provide an opportunity to study α-particle-dominated plasmas and burning-plasma physics in the laboratory.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
The effects of multispecies Hohlraum walls on stimulated Brillouin scattering, Hohlraum dynamics, and beam propagation
We report experiments and simulations have been conducted to investigate the efficacy of Ta 2 O 5 -lined Hohlraum walls at reducing stimulated Brillouin backscattering (SBS) as well as any subsequent effects on the Hohlraum dynamics and capsule implosions in indirect drive experiments at the National Ignition Facility. Using a 1.1 MJ 400 TW, 351 nm, shaped laser pulse, we measure a 5× reduction in SBS power in the peak of the pulse from the wall on the outer 50° cone beams. The SBS spectrum indicates a reduction in the high-Z spectral signature when using multispecies wall materials. Detailed hydrodynamic simulations were performed using different heat conduction models with flux limiters. Additional simulations were performed on the plasma maps using the 3D parallel paraxial code pF3D to compare backscatter powers between the pure Au and Ta 2 O 5 -lined Hohlraums. Further analysis, using hydrodynamically equivalent plasmas, shows that the SBS reduction is clearly a result of the added ion Landau damping caused by the oxygen ions and not from differences in plasma conditions. The experimental and simulation results also show an increase in the wall plasma expansion when using the Ta 2 O 5 liner leading to a 70% more oblate implosion.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Record Energetics for an Inertial Fusion Implosion at NIF
Inertial confinement fusion seeks to create burning plasma conditions in a spherical capsule implosion, which requires efficiently absorbing the driver energy in the capsule, transferring that energy into kinetic energy of the imploding DT fuel and then into internal energy of the fuel at stagnation. In this work, we report new implosions conducted on the National Ignition Facility (NIF) with several improvements on recent work [Phys. Rev. Lett. 120, 245003 (2018); Phys. Rev. E 102, 023210 (2020)]: larger capsules, thicker fuel layers to mitigate fuel-ablator mix, and new symmetry control via cross-beam energy transfer; at modest velocities, these experiments achieve record values for the implosion energetics figures of merit as well as fusion yield for a NIF experiment.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Optimization of capsule dopant levels to improve fuel areal density*
Not Available
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Application of cross-beam energy transfer to control drive symmetry in ICF implosions in low gas fill Hohlraums at the National Ignition Facility
Cross beam energy transfer (CBET), invoked by setting a wavelength difference, Δλ, between inner and outer beam cones, can be used to increase the drive on the waist in indirectly driven inertial confinement fusion experiments at the National Ignition Facility (NIF). Historically, hot spot symmetry control in capsule implosions in high (≥0.9 mg/cm 3 4 He) gas fill Hohlraums was enabled by substantial CBET. However, these implosion designs suffered from inflight symmetry swings, high SRS backscatter on the inner cones, and significant hot electron generation posing a threat to DT fuel preheat. Subsequent experiments in larger, low (≤0.6 mg/cm 3 4 He) gas fill Hohlraums demonstrated round implosions by varying the inner cone fraction throughout the laser drive at Δλ = 0 Å while keeping backscatter and hot electron generation very low. To enable driving larger capsules at a given Hohlraum size, additional tools for implosion symmetry control are required. With this goal in mind, here we present a detailed experimental study of using CBET in low gas fill Hohlraums near NIF's current peak power capability. We find a ~2.5× higher sensitivity of the P 2 Legendre mode with respect to Δλ changes compared to that of high gas fill designs. We attribute this observation to the fact that backscatter remains very low and that CBET remains in a linear regime, as suggested by simulations. As a result, a much smaller Δλ of order 1 Å is sufficient for sustaining implosion symmetry while keeping laser-to- Hohlraum coupling high and hot electron generation very low. While this study used plastic ablator capsules, our findings can be generalized to other ablator materials and, hence, show great promise for using wavelength detuning as a strong lever for implosion symmetry control in future low gas fill designs that require smaller case to capsule ratios in order to increase the energy coupled to the capsule.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
Measurements of enhanced performance in an indirect drive inertial confinement fusion experiment when reducing the contact area of the capsule support
Experimental results from indirectly driven inertial confinement fusion experiments testing the performance gained from using an alternate capsule tent support are reported. The polar tent describes an alternate geometry for the thin membrane used to support the Deuterium–Tritium (DT) filled capsule. In this work, the contact area is reduced by 23 times by locating the tent support close to the poles of the capsule. The polar tent experiments are repeats of previous 3 shock 1.63 MJ, 400 TW high foot experiments and use a 165 μm thick silicon doped carbon hydrogen plastic (CH) shell. Using the polar tent support, we report a DT neutron yield of 1.07 ×1016, 76% higher than the expected Y DT ∝V 7.7 scaling. This is, at the time of writing, the highest neutron yield to date from a CH shell implosion. Furthermore, we find that the inferred pressure when using the polar tent is significantly above the model based on analytic scaling even when accounting for tent effects. Analysis of x-ray and neutron images shows the reduction of lobes produced by nominal tent features. The reduction of these features in the polar tent experiments leads to decreased low mode (P2 and P4) asymmetry compared to the nominal tent results.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
A simple model to scope out parameter space for indirect drive designs on NIF
In this work, we present a simple model to scope out parameter space for indirect-drive, inertial confinement fusion designs for the National Ignition Facility laser. Because the parameter space is large, simple models can be used to identify regions of parameter space for further study with more sophisticated models and experiments. We include a model for Hohlraum radiation drive and symmetry—both based on empirical scalings from the data. The model for radiation drive is based on assuming that the high atomic number (Z) Hohlraum wall dominates the energy balance during the high power, peak of the pulse (≳ 300 TW). We find that the time-dependent radiation drive flux can be described by the running integral of the laser energy divided by the Hohlraum area multiplied by constant slopes in two distinct time periods. The first period is when the laser power rises rapidly, so the radiation temperature increases due to changes in laser power and wall albedo. The second period is during peak power—here, the laser power is typically held constant—so, the radiation temperature increases only due to changes in the wall albedo. This model is applied to several NIF designs with different Hohlraum sizes, laser pulse length durations, and peak powers and energies. Drive and symmetry models can be combined to find regions of parameter space that have high capsule absorbed energy while maintaining a symmetric implosion. We propose a new metric for evaluating designs based on minimizing the radius at which the maximum implosion kinetic energy is achieved.
70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗