Search NASA⌕ Search

Engineering topics

Hirschhorn, Jacob Aaron

Publications and source records attributed to Hirschhorn, Jacob Aaron.

Wrought FeCrAl alloy (C26M) cladding behavior and burst under simulated loss-of-coolant accident conditions

Cladding burst experiments for FeCrAl cladding were performed in the Severe Accident Test Station facility at Oak Ridge National Laboratory. These experiments were simulated using the BISON fuel performance code to better understand the cladding plastic behavior and failure under simulated loss-of-coolant accident conditions. 3D cladding surface boundary conditions were generated using composite axial and azimuthal profiles from experiment thermocouple data. To improve the simulation analysis capabilities in BISON for cladding burst behavior, new thermal creep, plasticity, and failure stress models specific to C26M, a wrought FeCrAl alloy, were developed and implemented. Initial cladding burst results indicated a general underprediction in the failure temperature of the six cladding burst simulations versus the observed failure temperatures. Close investigation of the experiment timing versus the underlying tensile test data revealed that, compared with the tensile specimens, the cladding tubes did not experience the same long holding time at high temperatures. New tensile tests were performed at high temperatures using a temperature ramp similar to the simulated loss-of-coolant accident experiments. These new tensile curves showed an approximately 80% increase in the ultimate tensile strength of the C26M alloy, indicating that a holding time of 10 min at 700 °C and 800 °C allows annealing to change the material microstructure. Using the updated tensile properties, the burst temperatures and stresses from the simulations showed remarkable agreement with the experimental results. This study was then extended by varying the initial pressure to highlight the burst temperature difference between standard Zircaloy-4 and C26M cladding under equivalent conditions. The results show that C26M has a burst temperature that is approximately 70–130 K greater than that of Zircaloy-4. In conclusion, these modeling predictions can be further improved by collecting high-temperature tensile data for C26M beyond the temperature ranges used in this work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

BISON Simulated and Experimental Fission Product Release Comparisons from Reradiated AGR-3/4 Compacts During High Temperature Heating Tests

The fuel performance modeling code BISON was used to predict the release of fission products iodine-131 (131I), xenon-133 (133Xe), and krypton-85 (85Kr) from four re-irradiated AGR-3/4 fuel compacts containing tristructural isotropic (TRISO) coated particles during high-temperature isothermal heating tests. The AGR-3/4 fuel compacts were irradiated in the Advanced Test Reactor (ATR) as part of the third and fourth series of planned experiments to support the Advanced Gas Reactor (AGR) Program. They were subsequently stored and re-irradiated in the Neutron Radiography (NRAD) reactor for approximately five days and then stored for another five to eight days before being subjected to isothermal heating tests in the Fuel Accident Condition Simulation (FACS furnace) for 200 to 300 hours at temperatures between 1000°C and 1600°C to evaluate fission product release at elevated temperatures. New nuclide-specific fission product source term models for the three nuclides of interest were developed using the reactor multiphysics code Griffin and implemented into BISON to support this work. The new source term models were incorporated into coupled compact- and particle-scale BISON simulations, which predict spatially- and temporally-resolved radionuclide generation, radioactive decay, transport, and release throughout the entire irradiation history, including the initial ATR irradiation, NRAD re-irradiations, FACS heating tests, and intermediate periods spent in storage. The experimentally measured fission product release from the heating tests were compared to modeling release predictions calculated by BISON to evaluate how well the code compares to experimental results. Overall, the experimental measured and BISON predicted comparative release results varied but generally agreed to within 5 particle equivalents. Comparative release results identified general observations to take into consideration to help refine future models and reduce uncertainties associated with both the measurement results and predictive results. This includes developing new uranium oxycarbide (UCO) specific kernel diffusivities for the three isotopes examined to more accurately reflect the material properties of the fuel form. Deriving new diffusivities will aid in producing a more informed BISON model

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Pre-Test Feasibility Study Of Reactivity Transient Testing On TRISO Fuel In The TREAT Reactor

Uranium oxycarbide (UCO)-bearing tri-structural isotropic (TRISO) particle fuels are expected to be used in numerous US commercial reactor applications within the next decade. In this work, we reviewed historical particle fuel transient experiments to identify gaps in the TRISO fuel performance transient testing. A BISON--Griffin modeling framework was then developed to conduct preliminary TRISO transient analyses and begin to address these gaps. The framework was demonstrated using limiting-case transient conditions from a prototypic high-temperature gas-cooled reactor. It was then applied to develop a matrix of experiments that could be performed in the Transient Reactor Test Facility (TREAT) to (1) evaluate UCO-fueled particle performance at moderate and high heat rates, (2) assess whether historical testing involving UO$_2$-fueled particles is applicable to modern UCO-fueled particles, (3) deconvolute the impacts of temperature and heat rate on particle transient response, and (4) collect the data needed for fuel performance model validation and/or further development.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Improvement of mechanistic fuel-cladding chemical interaction modeling in BISON

This report describes work performed during FY2024 under the auspices of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program to inform and improve mechanistic models of fuel-cladding chemical interaction (FCCI) in metallic fuel. For fuel-side FCCI, atomistic simulations were performed to determine the diffusivity of iron (Fe) in the $\alpha$ and $\gamma$ phases of uranium (U). A model of liquid penetration of cladding due to melting of the fuel-side FCCI region was updated to account for the finite size of the FCCI region, and the model was validated through comparison with tests performed in the Fuel Behavior Test Apparatus (FBTA). For cladding wastage formation, a reduced-order model was improved by comparison with a multi-scale mechanistic model to better quantify the ROM parameters.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Lower length scale model for palladium attack of silicon carbide in TRISO fuel

TRistructural ISOtropic (TRISO) particle fuels rely on silicon carbide (SiC) as the primary barrier for metallic fission product (FP) release. Palladium (Pd) generated by fission degrades the SiC layer, resulting in the formation of lamellar layers of palladium silicides (PdxSi) and carbon (C) perpendicular to the direction of attack. The Pd attack has been hypothesized to be responsible for failure of the SiC layer and enhance FP release. To better understand and quantify Pd attack of SiC in TRISO particles, a multiscale, mechanistic model of Pd transport is being developed by the NEAMS program. Previous work provided an initial hypothesis for modeling lamellar microstructure formation in SiC due to Pd attack using a phase-field model. The work described in this report builds on the previous model by using molecular dynamics (MD) simulations to parameterize the phase-field model kinetics, and build a reduced order model in BISON using the improved mesoscale Pd penetration model.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Complete Development of Critical Capabilities for TRISO Fission Product Source Term Calculations and Quantify Mechanisms for Pd Penetration of SiC

Overall fission product (FP) release will be an important consideration for the licensing and deployment of advanced reactors utilizing tristructural isotropic (TRISO) fuels. This work focuses on enhancing and applying the BISON models needed to predict FP transport within TRISO particles and particle failure probability, both of which factor directly into release predictions. Specifically, this report details (1) the development of the models needed to predict palladium (Pd) conservation at the engineering scale and the application of those models to characterize Pd fluxes for input into a mechanistic multiscale model for Pd penetration; (2) the refinement of sorption mass transfer models and the development of models for trapping in porous layers, which were applied and compared to particle scans from AGR-2 to provide proof of concept for a method of particle-scale validation that may reduce uncertainties compared to compact-scale validation using data from integral effects tests; (3) the development of a failure-statistics-informed, mesh-independent methodology for applying smeared cracking, enabling further study of the localized multiphysics behaviors associated with cascading particle failure mechanisms; and (4) the preliminary characterization of those coupled multiphysics particle failure behaviors using smeared, nonretentive diffusivities to provide a baseline for future study and to guide ongoing engineering applications.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The effect of temperature and burnup on U-10Zr metallic fuel chemical interaction with HT-9: A SEM-EDS study

The fuel cladding chemical interaction (FCCI) between Uranium-Zirconium-based metallic fuel and cladding materials during in-pile service is one of the most constraining phenomena affecting the performance of this fuel system. In this study, we investigated the effect of temperature and burnup on the FCCI development in two U-10 wt.% Zr (U-10Zr) fuel samples with HT-9 cladding irradiated as part of the MFF-3 irradiation test in the Fast Flux Test Facility (FFTF). One sample achieved a burnup of 13.1 at.% and operated with an average inner cladding temperature of 530°C, while the other achieved a burnup of 8.5 at.% and was subjected to an average inner cladding temperature of 615°C. Automated scanning electron microscopy (SEM) back-scattered electron (BSE) imaging of entire fuel cross-sections and SEM energy dispersive x-ray spectroscopy (EDS) analysis on specific fuel-cladding interface regions successfully provided a comprehensive characterization of the depth and type of interaction happening under different irradiation conditions. Further, our analysis shows that FCCI development on both fuel and cladding side is strongly influenced by the inner cladding temperature and, to some extent, the formation and integrity of Zr-rich layers between the fuel and cladding, while the impact of burnup and power is negligible. Measured FCCI thicknesses were compared to BISON simulations using both an empirical model based upon legacy data from the Experimental Breeder Reactor II (EBR II) irradiations and a mechanistic model currently under development for the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, showing satisfactory agreement. Nonetheless, this comparison supports the need for additional microstructural characterization in intermediate ranges of temperature, power, and burnups in prototypic-length pins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development and application of sorption mass transfer models for fission product transport in TRISO fuel systems using BISON

Fission product mass transfer within and between TRISO particle and compact layers is an important phenomenon. It directly impacts fission product release predictions, which are used as source terms for safety and licensing calculations. Modeling fission product transport within layers and across bonded interfaces is relatively straightforward under the assumptions of isotropic Fickian diffusion, concentration continuity, and flux continuity. Modeling fission product transport across gaps and debonded layers is more difficult. Gaps are known to form between the buffer and inner PyC (IPyC), and debonding may occur between the IPyC and silicon carbide (SiC). A new mass transfer model was developed to provide a more accurate and robust fission product release calculation by accounting for interlayer sorptivity. One importance of the new model is to account for temperature and material changes across the gap based on sorption isotherm. This work presents the development of the sorption behavioral model and a fission product trapping model, and analyses the subsequent fission product diffusion behavior, specifically cesium, through TRISO particles and compact materials using the BISON fuel performance code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Effective Lanthanide Diffusivity through U-Zr Metallic Fuel

Fuel-cladding chemical interaction (FCCI) is one of the main concerns for the performance of U-Zr metallic fuels. Although FCCI results in complex phase transformations and morphological changes in both the fuel and cladding sides of the interface, the formation of a brittle layer in the cladding side of the interface (sometimes referred to as wastage) has one of the most significant impacts on the cladding mechanical integrity. This brittle layer is associated with the formation of intermetallic compounds between the cladding constituents Fe, Cr and the lanthanide fission product species. The formation of this cladding wastage layer has been the focus of recent efforts to develop a mechanistic modeling framework, including production of lanthanides in the fuel, transport through the fuel to the fuel-cladding interface, and phase transformation to form intermetallic phases. To calculate the rate of transport of lanthanides through the fuel, a multi-scale computational approach has been used. Atomistic calculations have been performed to determine the diffusivities of Nd, the most prevalent lanthanide species, through the solid fuel matrix and along pore surfaces. These diffusivities have been used as input parameters for a mesoscale model to determine an effective diffusion coefficient that accounts for the formation of porosity, its interconnection, and infiltration with bond sodium from the fuel-cladding gap. The effective diffusivity has been used in engineering-scale simulations using the BISON fuel performance code, and BISON simulations have been compared to representative validation cases from the EBR-II reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Mechanistic FCCI model for BISON

In this report, multi-scale simulations to develop a mechanistic model of fuel-cladding chemical interaction (FCCI) conducted under the auspices of the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program in FY23 are described. The model assumes that cladding wastage is dominated by the intermetallic phase (Fe,Cr)$_{17}$Nd$_2$, and calculates production and diffusion of Nd in the fuel, diffusion into the cladding, and formation and growth of the intermetallic wastage layer. Atomistic simulations are used to calculate diffusivity of Nd in the (Fe,Cr) system. Mesoscale simulations, informed by previous atomistic calculations, are used to determine the effective diffusivity of Nd through the fuel, accounting for empty and sodium-filled porosity within the fuel. The BISON model incorporates this data and calculates the wastage layer thickness as a function of time, assuming parabolic growth kinetics based on the best available data. The results of the new mechanistic BISON model are compared to existing assessment cases for the X447 experiment in EBR-II, and show good agreement with experimental data and the existing BISON empirical model. To improve predictions of kinetics for future work, a phase-field model that includes fuel, wastage, and cladding phases is developed. Preliminary testing indicates that the kinetics may differ significantly from the assumed parabolic growth law, suggesting direction for future improvement of the model that will allow it to be applied to other fuel designs with greater confidence.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Improved Fuel Particle and Compact Matrix Fission Product Release Prediction with Improved Mass Transfer Model

This study was motivated by the need to incorporate more physics-based mass transfer models in BISON in order to improve fuel particle and compact matrix fission product release prediction. This document details the integration of new modeling capabilities in BISON, including (1) development of sorption mass transfer models; improvement of thermal contact model by adding neon to the gas gap inventory, (3) implementation of PCEA and IG-110 graphite thermal models, (4) validation using Advanced Gas Reactor (AGR)-3/4 compact and capsule rings data. These new capabilities have been shown to enforce the desired physics with satisfactory accuracy. BISON’s predictions of fission product release of AGR-3/4 compacts compare favorably with PARFUME and the concentration profiles across capsule rings show reasonable trend to the experiment measurement.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗