Search NASA⌕ Search

Engineering topics

Hisham Shehata

Publications and source records attributed to Hisham Shehata.

7 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Increasing the Dynamic Pressure Capability of the NASA Langley/ODU 6-inch MSBS

The 6-inch NASA/ODU Magnetic Suspension and Balance System (MSBS) has been configured for dynamic stability testing of blunt-body atmospheric entry capsules. Tests have been successfully accomplished in the low-speed, open-circuit wind tunnel, at speeds up to around 40 m/s. The wind tunnel is designed to reach around 150 m/s, resulting in dynamic pressures comparable to those projected to arise in a future supersonic MSBS facility. Extensive system upgrades are being undertaken to permit testing at higher speeds/dynamic pressures, including control system enhancements, revised position and attitude sensing, and activation of additional electromagnets in the existing array. This paper will review recent progress in all these areas.

Mark Schoenenberger↗
NASA NTRSDate not supplied

The Feasibility of Motion Tracking Camera System for Magnetic Suspension Wind Tunnel Tests

The Entry Systems Modeling (ESM) Program at NASA has actively participated in the re-development of the Magnetic Suspension Balance System (MSBS) at the six-inch subsonic wind tunnel at NASA Langley Research Center. This initiative aims to enhance the MSBS system's capabilities, enabling the testing of stingless entry vehicle models at supersonic speeds. To achieve this, control algorithms are required to ensure magnetic levitation control and stability for models during free-oscillation dynamic responses. Currently, the system relies on electromagnetic position sensors to provide real-time 3 degrees of freedom in a rigid body. While this approach has proven successful for subsonic speeds, expanding testing under higher pressure conditions may necessitate the incorporation of real-time roll and pitch measurements to quantify the dynamic stability characteristics of the models in free-oscillation. In collaboration with Old Dominion University, the team at NASA Langley Research Center proposes the implementation of a motion-tracking camera system. This system will provide real-time five degrees of freedom output, which will be utilized within a closed feedback control system and a two-step system identification model to isolate aerodynamic forces from their corresponding magnetic forces. The motion-tracking cameras will offer precise and accurate control over the levitation system, facilitating precise and repeatable experiments within the wind tunnel. The real-time feedback provided by the cameras enables prompt adjustments to ensure the maintenance of stable levitation throughout the testing process.

Entry Systems Modeling↗
NASA NTRSDate not supplied

Uncertainty Modeling for Mars Ascent Vehicle’s Aerodynamic Database Development

The design of the Mars Ascent Vehicle - Mars Sample Return (MAV-MSR) trajectories requires an accurate assessment of flight performance. Typically, these trajectories are developed by flight mechanics analysis to meet complex mission requirements and then flight performance assessed through Monte Carlo simulations. Consequently, it is crucial to develop an aerodynamic aerodatabase as an input model for flight mechanics analysis to provide static and dynamic force and moment coefficients under specific flight conditions. The force and moment coefficients in the MAV aerodatabase are determined using the FUN3D computational fluid dynamics solver. Firstly, an overview of the aerodatabase is presented to demonstrate its applicability to trajectory-defined simulations. This effort is followed by an initial attempt to quantify uncertainties in the force and moment coefficients necessary for updating the current aerodatabase. The uncertainty model identifies uncertainty adders and multipliers for coefficient-based forces and moments through a direct comparison between FUN3D and wind tunnel test data from NASA Marshall Space Center's 14x14 inch Trisonic Wind Tunnel. These uncertainties aim to encompass various changes in Mach number, angle of attack, and aerodynamic roll angle.

Uncertainty analysis↗
NASA NTRSDate not supplied

Development of Data Reduction Methods for Dynamic Stability Tests in a Magnetic Suspension and Balance System

The NASA/ODU 6-inch Magnetic Suspension and Balance System (MSBS) is operational in a “free-to-yaw” configuration in a subsonic wind tunnel. The MSBS hardware has been heavily modified over recent years to utilize a transverse magnetization scheme, with mixed electromagnetic and motion tracking camera position sensors and a relatively sophisticated control system. The project aims to provide a unique test capability for dynamic stability testing of planetary entry capsules, free from support interference. Aerodynamic tests are being conducted, with a focus of validation of the data reduction methods used to extract dynamic stability parameters. The unique complication is the existence of magnetic, aerodynamic, and mass centers, where magnetic, aerodynamic, and inertia forces respectively are resolved. The paper will report on tests of a family of EEV-like geometries, where the conical half-angle varied between 45 and 60 degrees in steps of 3.75 degrees. The paper will present experimental results from the parametric family of EEV-like geometries. Simulation results will also be presented, based on a two or three degree-of-freedom Simulink model. The model allows the exploration of the effects of non-coincident centers and the sensitivity of results arising from uncertainties in location.

Entry Systems Modeling↗
NASA NTRSDate not supplied

Dynamic Stability Test Technique for Blunt Bodies in a Magnetic Suspension and Balance System

Techniques for the measurement of subsonic dynamic stability derivatives of blunt-body re-entry capsules are being developed using a Magnetic Suspension and Balance System at NASA Langley Research Center. The measured aerodynamics of a 45-degree sphere-cone similar to configurations being considered for Mars Sample Return Earth Entry Vehicle are reported. A novel test method has been developed where forced oscillatory translation of a test article is used to excite yaw attitude oscillations. The forced motion is then halted to observe free-to-oscillate behavior of the test article. Parameter identification methods are used to extract drag as well as static and dynamic yawing moment stability characteristics from the measured forces and observed attitude histories. This combination of forced excitation followed by free-to-oscillate dynamics is a repeatable method to produce test article attitude histories that can be used to measure aerodynamic characteristics.

Entry Systems Modeling↗