Engineering topics
Publications and source records attributed to Ho, T. L..
The effects of solitons on the spectrum of fermion excitations in superfluid (He-3)-A are investigated. It is found that there is a two-dimensional manifold of bound states with energies within the gap of the bulk superfluid. The bound-state spectrum lacks inversion symmetry parallel to the wall.
A test program was carried out to evaluate several new high-temperature friction materials for use in aircraft disk brakes. A specially built test apparatus utilizing a disk brake and wheel half from a small jet aircraft was used. The apparatus enabled control of brake pressure, velocity and braking time. Tests were run under both constant and variable velocity conditions and covered a kinetic energy range similar to that encountered in aircraft brake service. The materials evaluation showed that two newly developed friction materials show potential for use in aircraft disk brakes. One of the materials is a nickel-based sintered composite, while the other is a molybdenum-based material. Both materials show much lower wear rates than conventional copper-based materials and are better able to withstand the high temperatures encountered during braking. Additional materials improvement is necessary, however, since both materials show a significant negative slope of the friction-velocity curve at low velocities.
Predictions of wear on contemporary copper-based brake material sliding against 17-22 AS grade steel, wear testing equipment, formulation of wear, and test results are discussed. An initial investigation of worn surfaces of the brake material and a mating steel rotor was carried out. A wear model proposed suggests initiation of cracks at a hard particle inclusion site in the surface layer of the brake material; crack propagation allows particles to be removed by intersection of cracks. Mutual relations between sliding variables, load, time, hardness, and surface temperature are studied. Empirical formulas are exhibited.
An investigation of both worn surfaces of friction pads and steel rotors which are being applied in current aircraft brakes has been carried out by employing an X-ray diffraction technique. It consists of the analysis of chemical element distribution in the surface layers. The wear particles were also examined by using the scanning electron microscope. The initiation and growth of surface cracks and the oxidation were emphasized in this investigation. A wear model was proposed for the current aircraft brake materials. Essentially this model proposed that cracks are formed in the surface layer of the brake material due to the normal and frictional stresses. It is primarily surface temperature dependent.
A research program was initiated to determine the feasibility of using cooling to increase brake life. An air cooling scheme was proposed, constructed and tested with various designs. Straight and curved slotting of the friction material was tested. A water cooling technique, similar to the air cooling procedure, was evaluated on a curved slotted rotor. Also investigated was the possibility of using a phase-change material within the rotor to absorb heat during braking. Various phase-changing materials were tabulated and a 50%, (by weight) LiF - BeF2 mixing was chosen. It was shown that corrosion was not a problem with this mixture. A preliminary design was evaluated on an actual brake. Results showed that significant improvements in lowering the surface temperature of the brake occurred when air or water cooling was used in conjunction with curved slotted rotors.
An initial investigation of worn surfaces in friction pads and steel rotors used in current aircraft brakes was carried out using electron microprobe and X-ray diffraction analysis. It consists of the topographical study and the analysis of chemical element distribution. Based upon this initial examination, two approaches, microscopic and macroscopic have been conducted to interpret and formulate the wear mechanism of the aircraft brake materials. Microscopically, the wear particles were examined. The initiation and growth of surface cracks and the oxidation were emphasized in this investigation. Macroscopically, it has been found that, for the current copper based brake material sliding against 17-22 AS steel in a caliper brake, the surface temperature raised due to frictional heat is nonlinearly proportional to the load applied and slide time with speed at 1750 rpm. The wear of brake materials is then proportional to this temperature and is also a function of the melting temperature for copper.
A test program is described which was carried out to evaluate several proposed design modifications and several high-temperature friction materials for use in aircraft disk brakes. The evaluation program was carried out on a specially built test apparatus utilizing a disk brake and wheel half from a small het aircraft. The apparatus enabled control of brake pressure, velocity, and braking time. Tests were run under both constant and variable velocity conditions and covered a kinetic energy range similar to that encountered in aircraft brake service. The results of the design evaluation program showed that some improvement in brake performance can be realized by making design changes in the components of the brake containing friction material. The materials evaluation showed that two friction materials show potential for use in aircraft disk brakes. One of the materials is a nickel-based sintered composite, while the other is a molybdenum-based material. Both materials show much lower wear rates than conventional copper-based materials and are better able to withstand the high temperatures encountered during braking. Additional materials improvement is necessary since both materials show a significant negative slope of the friction-velocity curve at low velocities.
The requirements of brake materials were outlined and a survey made to select materials to meet the needs of high temperature brakes. A number of metals and ceramic materials were selected and evaluated in sliding tests which simulated aircraft braking. Nickel, molybdenum tungsten, Zr02, high temperature cements and carbons were tested. Additives were then incorporated into these materials to optimize their wear or strength behavior with particular emphasis on nickel and molybdenum base materials and a high temperature potassium silicate cement. Optimum materials were developed which improved wear behavior over conventional brake materials in the simulated test. The best materials are a nickel, aluminum oxide, lead tungstate composition containing graphite or molybdenum disulphite; a molybdenum base material containing LPA100 (an intermetallic compound of cobalt, molybdenum, and silicon); and a carbon material (P5).