Search NASA⌕ Search

Engineering topics

Hoffman, James

Publications and source records attributed to Hoffman, James.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Performance and economic viability assessment of a novel CO 2 adsorbent for manufacturing and integration with coal power plants

Here, this study assesses the performance and economic feasibility of a novel CO 2 adsorbent for post-combustion capture in DOE/NETL’s 650 MWnet SubC PC power plant (case B11B). Bench-scale tests showed an initial adsorption capacity of 16.3 wt%, which decreased to 12.1 wt% after 41 adsorption–desorption cycles due to induced particle aggregation by over-humidification. With a conservative adsorption capacity of 8.8 wt% and 695 adsorption–desorption cycles, an adsorbent replenishment rate of 10 tonnes/h is necessary to capture 90% of CO 2 . The breakeven sale price of the adsorbent produced at this rate is $\$$1,293/tonne, which is 40 to 80 times lower than prices for K 2 CO 3 adsorbents reported in the literature (e.g., K 2 CO 3 /TiO 2 , K 2 CO 3 /ZrO 2 ) while providing better capture performances. Sensitivity analysis reveals that increasing the plant production rate from 10 to 40 tonnes/h reduces the sale price by 8%. The study also compares the CO 2 capture cost to Cansolv, an integrated solvent-based technology. The novel adsorbent requires 2.4 GJ/tonne of CO 2 for regeneration, lower than Cansolv’s 2.7 GJ/tonne. With conservative performance estimates, the capture cost is $\$$54/tonne of CO 2 , slightly higher than Cansolv’s $\$$45/tonne. To achieve lower or comparable capture costs to Cansolv, the adsorbent should meet one of the following conditions at a commercial scale: minimum 950 cycles, 16 wt% capture capacity, 50% of the adsorbent recovery, or a reduced cost to $\$$646/tonne by upscaling the manufactury to 75 tonnes/h.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

The NETL DAC Center: Design and Capabilities

Description of NETL's Direct Air Capture (DAC) Center, including design and capabilities of research units being installed for the evaluation of processes removing carbon dioxide from air.

Hoffman, James↗
DOE OSTI2023

Single polymer sorbent fibers for high performance and rapid direct air capture

Polymers of intrinsic microporosity (PIM) fibers featuring amidoxime and amine functionalities were formulated into high-performance CO 2 adsorbents. Fiber sorbents were composed of a single porous polymer component functionalized with molecular amines to increase the CO 2 capture uptake and kinetics. Here we report the highest CO 2 uptake capacity (3.3 wt% (0.8 mmol g –1 ) CO 2 at 400 ppm) among all PIM-based and single polymeric sorbents to date. Moreover, the sorbents exhibited rapid CO 2 adsorption rates (capturing 90% of its total capacity within 7 min.) and cost efficient and reproducible regeneration (at 70 °C) which are essential for reducing the cost of direct air capture.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Amine-functionalized porous organic polymers for carbon dioxide capture

Recent developments in CO 2 capture using porous organic polymers (POPs) have received accrescent attention due to their sorbent properties such as high CO 2 uptake capacity and selectivity, tunable chemical structure and permanent porosity. POPs are constructed using two and/or three-dimensional organic monomers (building blocks) linked to each other through covalent bonding, creating high porosity. The pore structure in POPs is exceptionally stable, which leads to their cyclable CO 2 adsorption performance. However, POPs generally suffer from low CO 2 uptake and selectivity due to their interaction with CO 2 in physisorption limits (20–40 kJ mol -1 ). Similar to that in other physisorbents, the CO 2 uptake capacity of POPs further decreases under humid conditions. Pursuant to these limitations, amine functionalization in POPs has resulted in enhanced CO 2 uptake performance with improved CO 2 selectivity over non-polar gases such as N 2 . More importantly, several types of amine-functionalized POPs showed that the CO 2 uptake could remain intact under humid conditions such as in post-combustion flue gas. This review article covers recent developments in amine-functionalized porous organic polymers. Three main categories of amine functionalization, such as direct amine synthesis, amine impregnation and amine grafting, were investigated in detail by considering the effect of amines on the sorbent properties and CO 2 capture performance of POPs. The recent findings in amine-functionalized POPs were investigated including porous polymeric networks (PPNs), covalent organic frameworks (COFs), amine linked POPs, hyper-crosslinked polymers (HCPs), conjugated microporous polymers (CMPs), benzimidazole linked polymers (BILPs), porous aromatic frameworks (PAFs) and polymers of intrinsic microporosity (PIMs).

36 MATERIALS SCIENCE↗
DOE OSTI2021

Comparison of microwave and conventional heating for CO 2 desorption from zeolite 13X

In this study, we investigate microwave irradiation as an alternative to conventional heating for temperature swing adsorption processes. The performance of microwave and conventional heating during sorbent regeneration was evaluated by measuring CO 2 desorption from zeolite 13X at different temperatures. Experimentally, a fixed bed of zeolite 13X was saturated by a 150 sccm flow of 15 % CO 2 at room temperature followed by sorbent regeneration under nitrogen at 55, 100, or 150 °C by applying either microwave irradiation or conventional heating. Microwaves reduced sorbent regeneration times by at least half compared to regeneration by conventional heating. Under conventional regeneration, desorption curves were resolved into two peaks representing physisorbed CO 2 (mass diffusion limited) at low temperature and bicoordinated CO 2 (thermally limited) with increasing temperature. Under microwave regeneration, only one desorption peak was observed suggesting that CO 2 desorption was limited by mass diffusion through the porous zeolite 13X structure, rather than by temperature. Depending on microwave power, apparent activation energy of the microwave-assisted regeneration was 15.8–18.1 kJ/mol, compared to 41.5 kJ/mol for conventional regeneration. The reduction in apparent activation energy is mainly attributed to selective microwave heating of CO 2 adsorption sites (Na + sites) resulting in greater steady state temperatures of Na + relative to framework atoms, suggesting greater heating efficiency due to microwaves compared to conventional heat transfer. Due to rapid cycling and efficient heat transfer to CO 2 sites on zeolite 13X, microwave regeneration is found to increase adsorption/desorption cycling productivity and potentially reduce the energy penalty of temperature swing capture.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS2021

Development of Gallium Nitride Monolithic Microwave Integrated Circuits for Ka-Band Remote Sensing

We have been developing gallium nitride (GaN)monolithic microwave integrated circuits (MMICs) towards thegoal of implementing a single chip transceiver frontend forcloud radar arrays at Ka-band. We present our first iterationdesign, fabrication and test cycle implementation of GaN poweramplifiers (PAs), low noise amplifiers (LNAs), driver amplifier,single-pole- double and triple throw switches, and voltagecontrolled attenuator. These components are necessary forimplementing a transceiver unit cell concept with digitalcalibration capabilities to enable scalable array sizes for radarand radiometry.

Cao, Yu↗
NASA NTRS2018

New Efforts to Update NASA's Global Reference Atmospheric Models (GRAM)

NASA is at the forefront of planetary exploration. The inability to test planetary spacecraft in the flight environment prior to a mission requires engineers to rely on ground-based testing and models of the vehicle and expected environments. One of the most widely used engineering models of the atmosphere for many NASA projects is the Global Reference Atmospheric Model (GRAM) developed by the NASA Marshall Space Flight Center (MSFC). Over the past decade GRAM upgrades and maintenance have depended on inconsistent and waning project-specific support. Recently, the NASA Science Mission Directorate agreed to provide funding support in Fiscal Year 2018 and 2019 to upgrade the GRAMs. This poster summarizes the objectives, tasks and milestones of this effort.

Dwyer Cianciolo, Alicia↗
NASA NTRS2014

A Compact Two-Stage 120 W GaN High Power Amplifier for SweepSAR Radar Systems

This work presents the design and measured results of a fully integrated switched power two-stage GaN HEMT high-power amplifier (HPA) achieving 60% power-added efficiency at over 120Woutput power. This high-efficiency GaN HEMT HPA is an enabling technology for L-band SweepSAR interferometric instruments that enable frequent repeat intervals and high-resolution imagery. The L-band HPA was designed using space-qualified state-of-the-art GaN HEMT technology. The amplifier exhibits over 34 dB of power gain at 51 dBm of output power across an 80 MHz bandwidth. The HPA is divided into two stages, an 8 W driver stage and 120 W output stage. The amplifier is designed for pulsed operation, with a high-speed DC drain switch operating at the pulsed-repetition interval and settles within 200 ns. In addition to the electrical design, a thermally optimized package was designed, that allows for direct thermal radiation to maintain low-junction temperatures for the GaN parts maximizing long-term reliability. Lastly, real radar waveforms are characterized and analysis of amplitude and phase stability over temperature demonstrate ultra-stable operation over temperature using integrated bias compensation circuitry allowing less than 0.2 dB amplitude variation and 2 deg phase variation over a 70 C range.

Thrivikraman, Tushar↗
NASA NTRS2013

Design of an Ultra-High Efficiency GaN High-Power Amplifier for SAR Remote Sensing

This work describes the development of a high-power amplifier for use with a remote sensing SAR system. The amplifier is intended to meet the requirements for the Sweep-SAR technique for use in the proposed DESDynI SAR instrument. In order to optimize the amplifier design, active load-pull technique is employed to provide harmonic tuning to provide efficiency improvements. In addition, some of the techniques to overcome the challenges of load-pulling high power devices are presented. The design amplifier was measured to have 49 dBm of output power with 75% PAE, which is suitable to meet the proposed system requirements.

active load-pull↗