Engineering topics
Publications and source records attributed to Hofmann, L. G..
A method by which modern and classical theory techniques may be integrated in a synergistic fashion and used in the design of practical flight control systems is presented. A general procedure is developed, and several illustrative examples are included. Emphasis is placed not only on the synthesis of the design, but on the assessment of the results as well.
An overview is presented of some of the promising washout schemes which have been devised. The four schemes presented fall into two basic configurations; crossfeed and crossproduct. Various nonlinear modifications further differentiate the four schemes. One nonlinear scheme is discussed in detail. This washout scheme takes advantage of subliminal motions to speed up simulator cab centering. It exploits so-called perceptual indifference thresholds to center the simulator cab at a faster rate whenever the input to the simulator is below the perceptual indifference level. The effect is to reduce the angular and translational simulation motion by comparison with that for the linear washout case. Finally, the conclusions and implications for further research in the area of nonlinear washout filters are presented.
The objective of this effort is to determine IFR approach path and touchdown dispersions for manual and automatic XV-15 tilt rotor landings, and to develop missed approach criteria. Only helicopter mode XV-15 operation is considered. The analysis and design sections develop the automatic and flight director guidance equations for decelerating curved and straight-in approaches into a typical VTOL landing site equipped with an MLS navigation aid. These system designs satisfy all known pilot-centered, guidance and control requirements for this flying task. Performance data, obtained from nonstationary covariance propagation dispersion analysis for the system, are used to develop the approach monitoring criteria. The autoland and flight director guidance equations are programmed for the VSTOLAND 1819B digital computer. The system design dispersion data developed through analysis and the 1819B digital computer program are verified and refined using the fixed-base, man-in-the-loop XV-15 VSTOLAND simulation.
The state of the art in active control technology is summarized. How current design criteria and airworthiness regulations might restrict application of this emerging technology to subsonic CTOL transports of the 1980's are discussed. Facets of active control technology considered are: (1) augmentation of relaxed inherent stability; (2) center-of-gravity control; (3) ride quality control; (4) load control; (5) flutter control; (6) envelope limiting, and (7) pilot interface with the control system. A summary and appraisal of the current state of the art, design criteria, and recommended practices, as well as a projection of the risk in applying each of these facets of active control technology is given. A summary of pertinent literature and technical expansions is included.
A program was undertaken to develop design criteria and operational procedures for STOL transport aircraft. As part of that program, a series of flight tests shall be performed in an Augmentor Wing Jet STOL Aircraft. In preparation for the flight test programs, an analytical study was conducted to gain an understanding of the characteristics of the vehicle for manual control, to assess the relative merits of the variety of manual control techniques available with attitude and thrust vector controllers, and to determine what improvements can be made over manual control of the bare airframe by providing the pilot with suitable command guidance information and by augmentation of the bare airframe dynamics. The objective of the study is to apply closed-loop pilot/vehicle analysis techniques to the analysis of manual flight control of powered-lift STOL aircraft in the landing approach and to the design and experimental verification of an advanced flight director display.
Pilot instrument scanning data collected during simulated transport instrument landing approaches is examined. Deterministic features of random pilot instrument scanning behavior are confirmed to be: transitions in point of eye fixation which originate and terminate on the same instrument are rare; and transitions in point of eye fixation which originate on one secondary instrument and terminate on another secondary instrument are rare. Link value estimators are developed using statistics and these experimental facts. The result has a special significance when there is but a single primary instrument, a flight director. The result is used to simplify the iterative computational procedure of STI's display theory to a non-iterative procedure for the flight director case.
Experimental eye scanning measurements were made from simulated instrument approaches in a flight-like cockpit representing a contemporary jet transport. The procedure for predicting the partition of the pilot's scanning workload required for monitoring and controlling a task with status displays and a flight director was simplified. When there is but a single director control display, iteration in the preliminary design computations is eliminated. The preliminary design computations are based on predictions of closed-loop input-correlated errors in displayed variables with respect to the trimmed flight values. Methods for predicting multiloop error coherence, and for correcting the predicted partition of scanning workload when the pilot's scanning remnant contribution is significant are included.
Reduced runway separation standards are among the means which have been proposed for increasing airport capacity. The probability of a blunder will dominate the calculation of safe separation standards. Then the determinant of safe system performance will be the system reaction time comprised of the air traffic controller's detection, decision and communication delays, and the response times of the pilot and aircraft in executing a collision avoidance manuever. Estimates of these times, based on existing data, show that the delays ascribable to the human portions of the man-machine system are comparatively unimportant. New developments in radar, computers, and data links will be required to provide any substantial improvement of the existing system, and the goal of 2500 ft of separation may not be achievable.
Adaptive control system compensates for changes in the dynamic characteristics of linear controlled elements. It is mechanized so that the actual input of each control approaches the ideal input.
Adaptive control function technique for lateral stability augmentation system design for manned lifting body entry vehicle
Adaptive control function technique to design lateral stability augmentation system for hypothetical manned, lifting body entry vehicle
New methods for design of adaptive flight control systems
Crossover models and optimal control theory for obtaining pilot performance data
Parameter tracking systems based on equation error approach for mathematical model of unknown plant
Transfer function approximations for large highly coupled flexible body launch vehicles with liquid fuel slosh