Engineering topics

Holland, Justin M.

Publications and source records attributed to Holland, Justin M..

4 records

DOE OSTI2024

Quantification of uranium metal and total uranium in U-UO 2 mixtures using H 3 PO 4 -HCl

Here, the selective dissolution of uranium metal from its mixtures with UO 2 was studied to establish a simple and rapid quantitative method. Uranium metal was found to selectively dissolve as U(IV) into a solution of phosphoric and hydrochloric acids, with quantitative dissolution occurring within 1 h. Total dissolution of uranium as U(VI) could then be obtained by nitric acid addition and heating for 0.5–1 h. Analysis of the resulting U(IV) and U(VI) solutions by ICP-OES or UV–Vis spectroscopy yielded uranium metal-to-UO 2 ratios with an accuracy of ± 10% or better. Accuracy of the ICP-OES method was slightly better than UV–Vis, but the simplicity of the latter makes it an attractive option for some applications.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Reactive Fe anode for electrolytic reduction of solid metal oxide in molten LiCl-Li 2 O

Iron metal was investigated for use as a consumable anode for electrolytic reduction of solid metal oxides in molten LiCl-Li 2 O (2.0 - 2.4 wt%). Tests were performed where the potential of Fe anodes was increased incrementally from 0.1 to 1.0 V (vs Ni/NiO). Oxide formation on the anode started at a potential of 0.4 V and was identified as FeO via X-ray diffraction. In the absence of a pre-formed oxide layer, severe attack of the anode started at a potential of 0.7 V and was accompanied by an increase in Fe concentration in the salt. When an oxide layer was allowed to form on the anode, the Fe concentration did not increase in the salt. O 2 was detected in the headspace gas at an anode potential of 1.0 V only when an oxide layer was present on the anode. Finally, the results of this study support the idea that an inexpensive sacrificial anode could be an ideal replacement for expensive Pt that is currently widely used for this process.

36 MATERIALS SCIENCE↗

DOE OSTI2024

UO 2 solubility and chemical interactions in molten LiCl-Li 2 O

Here, this study investigated the solubility of UO 2 in LiCl-2 wt% Li 2 O at 650 °C with O 2 partial pressures up to 114 torr. Experiments were run in which UO 2 powder was contacted with the molten salt for up to 120 h. Salt samples were taken and analyzed for U and corrosion product concentration using inductively coupled plasma mass spectrometry and for Li 2 O concentration using titration. The highest measured U concentration in the salt was 0.06 wt%, and O 2 partial pressure was observed to have little to no effect on the solubility. Increasing O 2 partial pressure did increase the concentration of corrosion products in the salt. The concentration of Li 2 O in the molten salt progressively decreased with time in contact with UO 2 . This can be explained by the formation of Li 2 UO 4 via reaction of UO 2 with Li 2 O.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Fluid level and conductivity sensor for high temperature applications

A fluid level and conductivity sensor having a sensing probe with four electrodes disposed therein particularly suited for high temperature applications. A distal end of the second and third electrodes are positioned a distance from the sensing end that is greater than distal ends of the first and fourth electrodes. The sensor includes an electronics system having a signal relay system for receiving signals from each of the electrodes and switching between different measurement modes by determining a resistance between selected pairs of electrodes based on instructions from the microcontroller. The measurement modes include a conductivity measurement mode in which a resistance between the first and fourth electrodes is determined, and a fluid level measurement mode in which a resistance between the first and third electrodes is determined and compared to a resistance between the second and third electrodes.

Holland, Justin M.↗