Search NASA⌕ Search

Engineering topics

Holmes, B. J.

Publications and source records attributed to Holmes, B. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Wind-tunnel investigation on the effect of a crescent planform on drag

Lift and drag forces were compared for elliptic and crescent wing models at cruise and climb conditions in the NASA/Langley 14 x 22-ft subsonic tunnel. The force measurements were obtained for an angle-of-attack range from -3 to 10 deg at a Reynolds number of about 1.7 million. The results indicate that for attached flow conditions, the crescent wing with its highly swept tips generates less lift-dependent drag than the elliptic wing for given lift force, wing span, and freestream conditions. The drag reduction is thought to be the result of the favorable influence of trailing wake deformations on the pressure distribution of the highly swept outboard region of the crescent wing.

Van Dam, C. P.↗
NASA NTRS1989

Wind-tunnel investigations of wings with serrated sharp trailing edges

Exploratory wind-tunnel force measurements are presented for two wing geometries with small-scale planar and nonplanar serrated trailing-edge devices (chord-Reynolds numbers ranged from 1.0 to 3.7 million). The planar serrated trailing-edge extensions reduced the drag at conditions when trailing-edge separation occurred at low angles of attack. The introduction of serrations reduced or eliminated the drag penalty, due to the small (1-2 percent of the chord length) nonplanar trailing-edge flaps, while maintaining the effects of increase in camber. The presence of streamwise vortices immediately downstream of the serrated trailing edges is believed to have favorably affected the boundary-layer flow approaching the trailing edge and the near-wake development, resulting in reduced pressure (form) drag.

Vijgen, P. M. H. W.↗
NASA NTRS1989

Sheared wing-tip aerodynamics - Wind-tunnel and computational investigation

Computational and experimental performance benefits are presented for a high-aspect-ratio unswept wing configuration with sheared tips. The sheared tip is a highly swept and highly tapered surface located in the same plane as the inboard wing panel to which it is attached. The compuational results were obtained with an inviscid surface panel method that models the nonlinear influence of the trailing wake. Both wind-tunnel and calculated results were obtained for a 12-ft span wing model with various wing-tip configurations. The computational and experimental data are in fair agreement and demonstrate that sheared wing tips can reduce induced drag at cruise and climb lift coefficients. The drag reduction is the result of wake deformation effects and changes in spanwise load distribution. Wind-tunnel measured longitudinal and lateral directional stability characteristics are also presented for the various wing-tip layouts.

Vijgen, P. M. H. W.↗
NASA NTRS1989

High-alpha aerodynamic characteristics of crescent and elliptic wings

Static longitudinal and lateral-directional forces and moments were measured for elliptic- and crescent-wing models at high angles of attack in the NASA Langley 14-by-22-ft Subsonic Tunnel. The forces and moments were obtained for an angle-of-attack range including stall and post-stall conditions at a Reynolds number based on the average wing chord of about 1.8 million. Flow-visualization photographs using a mixture of oil and titanium-dioxide were also taken for several incidence angles. The force and moment data and the flow-visualization results indicated that the crescent wing model with its highly swept tips produced much better high-angle-of-attack aerodynamic characteristics than the elliptic model. Leading-edge separation-induced vortex flow over the highly swept tips of the crescent wing is thought to produce this improved behavior at high angles of attack. The unique planform design could result in safer and more efficient low-speed airplanes.

Van Dam, C. P.↗
NASA NTRS1989

Wind-tunnel investigations of wings with serrated sharp trailing edges

Exploratory wind-tunnel force measurements are presented for two wing geometries with small-scale planar and nonplanar serrated trailing-edge devices (chord-Reynolds numbers ranged from 1.0 - 3.7 x 10 to the 6th). The planar serrated trailing-edge extensions reduced the drag at conditions when trailing-edge separation occurred at low angles of attack. The introduction of serrations reduced or eliminated the drag penalty due to the small (1-2 percent of the chord length) nonplanar trailing-edge flaps, while maintaining the effects of increase in camber. The presence of streamwise vortices immediately downstream of the serrated trailing edges is believed to have favorably affected the boundary-layer flow approaching the trailing edge and the near-wake development, resulting in reduced pressure drag.

Vijgen, P. M. H. W.↗
NASA NTRS1988

An arrayed hot-film sensor for detection of laminar boundary-layer flow disturbance spatial characteristics

An arrayed hot-film sensor has been developed for use in laminar boundary-layer research for the detection of crossflow or Goertler vortices. This sensor has been developed to detect spatial variations in heat transfer which are characteristic of crossflow or Goertler vortices. The sensor is ultimately intended for flight research applications. This paper describes the sensor, its priciples of operation, signal analysis techniques, and experimental results illustrating the spatial detection capabilities of this specialized hot-film device. Discretely placed spheres placed in the boundary layer created alternating regions of undisturbed and disturbed laminar flow over a prototype sensor. Flow visualization results were correlated with the sensor output to demonstrate the ability of the sensor to determine the spatial boundaries of localized disturbances in laminar flow. This work represents the initial steps toward the validation and calibration of an arrayed hot-film sensor for the detection of crossflow or Goertler vorticity wavelength and/or wave frequency.

Wusk, M. S.↗
NASA NTRS1988

Effects of compressibility on design of subsonic fuselages for natural laminar flow

Compressible linear boundary-layer stability analyses of two representative axisymmetric fuselage geometries indicate that a favorable effect will be exerted on the characteristics of a fuselage's axisymmetric boundary layer by compressibility. A freestream Mach number increase from 0.6 to 0.8 significantly reduces TS wave growth rates in the laminar boundary layer of the fuselages analyzed. The generally destabilizing effect of increasing length Re number on boundary layer stability can be overpowered by the favorable effects of compressibility on the fluid.

Vijgen, P. M. H. W.↗
NASA NTRS1988

In-flight flow visualization using infrared imaging

A flight test investigation was conducted to evaluate infrared (IR) flow imaging techniques for boundary-layer flow visualization. The flight tests used a single-engine turboprop aircraft with a fiberglass-skinned natural laminar flow glove mounted on the left wing and an infrared imaging system to obtain flow visualization data. Data were compared to results obtained from other more conventional boundary-layer flow visualization methods and found to agree well. Test flights were conducted to determine the effect of test surface color on IR flow visualization results. In addition, flights were made during both night and daylight hours to assess the effect of solar radiation on the results. The investigation included an effort to visualize a vortex passing over the wing glove, but the tests provided only limited results.

Brandon, J. M.↗
NASA NTRS1988

Analysis of wind-tunnel boundary-layer transition experiments on axisymmetric bodies at transonic speeds using compressible boundary-layer stability theory

The design of laminar flow fuselages and advanced swept wings at high-subsonic compressible speeds can benefit from a correlation of compressible transition experiments with the e exp n transition-prediction method. A computational analysis has been conducted to investigate the detailed transition measurements obtained by Boltz et al. (1956, 1960) for two bodies-of-revolution. Nonadiabatic wall conditions were included in the analysis when wall-temperature measurements were available.

Vijgen, P. M. H. W.↗
NASA NTRS1986

Flow diagnostics and visualization in wind tunnels and flight

The Langley Research Center has a concentrated and directed effort under way to develop both conventional and non-intrusive diagnostic instrumentation. These instruments are being developed to operate over large Mach number, total temperature, and total pressure ranges. Efforts are being made to evaluate the measurements made by the various instruments to determine the most accurate and reliable instrument to be used under a given flow environment. Although only one flow visualization technique was described, there are many different types presently being used at Langley Research Center.

Stainback, P. C.↗
NASA NTRS1986

Flight research on natural laminar flow

Five decades of flight experiences with natural laminar flow (NLF) have provided a basis of understanding how this technology can be used for reduction of viscous drag on modern practical aircraft. The effects of cruise unit Reynolds number on NLF achievability and maintainability; compressibility effects on Tollmein-Schlichting growth; flight experiment on the Cessna Citation III business jet; flight instrumentation on Lear 28/29; OV-I NLF engine nacelle experiments; and viscous drag reduction are examined.

Holmes, B. J.↗
NASA NTRS1986

Liquid crystals for high-altitude in-flight boundary layer flow visualization

A novel method for visualization of laminar to turbulent boundary layer transition in flight is presented, in which liquid crystal coatings are used to indicate the transition by a change of color (in response to the changes in the wall shear and the temperature). The liquid crystals applied to the wing surfaces were either cholesteric crystals formulated to be active between temperatures of 30 and 100 F or a sample of chiral nematic liquid crystals formulated to be active between -18 and -22 F. Liquid crystal coatings were shown to provide visualization data at flight altitudes and temperatures at which data could not be obtained previously. Flight evaluations were successfully conducted on a T-34C and a Learjet research aircraft at Mach numbers of up to 0.8 and altitudes of up to 50,000 ft. The time response during oscillating sideslip tests was very rapid. In wind tunnel tests, a hysteresislike behavior was observed in the liquid crystal coatings, possibly because of the lower dynamic pressures in wind tunnels as compared to flight.

Gall, P. D.↗
NASA NTRS1986

Boundary-layer transition effects on airplane stability and control

Surface contamination of laminar-flow airfoils can significantly modify the location of transition from laminar-to-turbulent boundary-layer flow. The contamination can be the result of insect debris, environmental effects such as ice crystals and moisture due to mist or rain, surface damage, or other contamination adhering to the surface. Location and mode of transition have a dominant effect on the lift-and-drag characteristics of a lifting surface. The influences of laminar boundary-layer flow behavior on airplane stability and control are examined through theoretical results and experimental (wind-tunnel and free-flight) data. For certain airfoils with a relatively steep pressure recovery it is shown that loss of laminar flow near the leading edge can result in premature separation of the turbulent boundary layer and, consequently, in loss of lift and control effectiveness. Aerodynamic modifications which minimize boundary-layer transition effects on airplane stability and control are also discussed.

Van Dam, C. P.↗