Search NASA⌕ Search

Engineering topics

Holoubek, John

Publications and source records attributed to Holoubek, John.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Healable and conductive sulfur iodide for solid-state Li–S batteries

Solid-state Li-S batteries (SSLSBs) are made of low-cost and abundant materials free of supply chain concerns. Owing to their high theoretical energy densities, they are highly desirable for electric vehicles. However, the development of SSLSBs has been historically plagued by the insulating nature of sulfur and the poor interfacial contacts induced by its large volume change during cycling, impeding charge transfer among different solid components. We report an S 9.3 I molecular crystal with I 2 inserted in the crystalline sulfur structure, which shows a semiconductor-level electrical conductivity (approximately 5.9 × 10 -7 S cm -1 ) at 25 °C; an 11-order-of-magnitude increase over sulfur itself. Iodine introduces new states into the band gap of sulfur and promotes the formation of reactive polysulfides during electrochemical cycling. Further, the material features a low melting point of around 65 °C, which enables repairing of damaged interfaces due to cycling by periodical remelting of the cathode material. As a result, an Li-S 9.3 I battery demonstrates 400 stable cycles with a specific capacity retention of 87%. The design of this conductive, low-melting-point sulfur iodide material represents a substantial advancement in the chemistry of sulfur materials, and opens the door to the practical realization of SSLSBs.

25 ENERGY STORAGE↗
DOE OSTI2023

Composite Lithium Metal Structure to Mitigate Pulverization and Enable Long‐Life Batteries

In lithium metal batteries, non‐uniform stripping of lithium results in pit formation, which promotes subsequent non‐uniform, dendritic deposition. This viscous cycle leads to pulverization of lithium which promotes cell shorting or capacity degradation, symptoms further exaggerated by high electrode areal loading and lean electrolytes. Here, to address this challenge, a composite lithium metal anode is engineered that contains uniformly distributed, nanometer‐sized carbon particles. This composite lithium is shown to strip more uniformly since the growth of non‐uniform pits is intercepted by the carbon particles. This mechanism is corroborated by a continuum electrochemical model. Subsequent lithium deposition on carbon particles is also found to be more uniform than on the surface with irregular pits. Notably, the pulverization rate of composite lithium is 26 times slower than that of commercial lithium. Moreover, in a Li‐S battery with sulfurized polyacrylonitrile cathode, the use of the composite anode extends the cycle life by three times when the areal capacity is 8 mAh cm −2 . The approach of using an engineered lithium composite structure to address challenges during both stripping and plating can inform future designs of lithium metal anodes for high areal capacity operations.

high areal capacity↗
DOE OSTI2022

Enhanced Electrolyte Transport and Kinetics Mitigate Graphite Exfoliation and Li Plating in Fast–Charging Li–Ion Batteries

Despite significant progress in energy retention, lithium-ion batteries (LIBs) face untenable reductions in cycle life under extreme fast-charging (XFC) conditions, which primarily originate from a variety of kinetic limitations between the graphite anode and the electrolyte. Through quantitative Li + loss accounting and comprehensive materials analyses, it is directly observed that the operation of LIB pouch cells at 4 C||C/3 (charging||discharging) results in Li plating, disadvantageous solid-electrolyte-interphase formation, and solvent co-intercalation leading to interstitial decomposition within graphite layers. It is found that these failure modes originate from the insufficient properties of conventional electrolytes, where employing a designed ester-based electrolyte improved the capacity retention of these cells from 55.9% to 88.2% after 500 cycles when operated at the aforementioned conditions. These metrics are the result of effective mitigation of the aforementioned failure modes due to superior Li + transport and desolvation characteristics demonstrated through both experimental and computational characterization. Finally, this work reveals the vital nature of electrolyte design to XFC performance.

25 ENERGY STORAGE↗
DOE OSTI2022

Hierarchically structured metal carbides as conductive fillers in thermo-responsive polymer nanocomposites for battery safety

Integrating thermo-responsive polymer switching materials (TRPS) into lithium-ion batteries (LIBs) has been recognized as one of the most effective strategies to prevent thermal runaway under various abuse scenarios. However, the current methods to obtain TRPS cannot satisfy different practical applications. Herein, we develop a versatile strategy for the preparation of various metal carbides (e.g., tungsten carbide, molybdenum carbide) with controllable hierarchical structure that is featured with surface protrusion structure, which is critical for high conductivity and rapid thermal response. Systematic studies of the phase and morphology evolutions by advanced characterizations illustrate that the reducing agent and reduction rate are critical for developing the specific morphology. In conclusion, by using the above-mentioned carbides as the conductive fillers of TRPS, the resulting TRPS with a specially controlled shape exhibits over 5 order of conductivity improvement compared with common carbides with particulate morphology, in addition to reversible shutdown performance and effective thermal abuse protections toward safe LIB operation.

25 ENERGY STORAGE↗
DOE OSTI2022

Solvent selection criteria for temperature-resilient lithium–sulfur batteries

All-climate temperature operation capability and increased energy density have been recognized as two crucial targets, but they are rarely achieved together in rechargeable lithium (Li) batteries. Herein, we demonstrate an electrolyte system by using monodentate dibutyl ether with both low melting and high boiling points as the sole solvent. Its weak solvation endows an aggregate solvation structure and low solubility toward polysulfide species in a relatively low electrolyte concentration (2 mol L −1 ). These features were found to be vital in avoiding dendrite growth and enabling Li metal Coulombic efficiencies of 99.0%, 98.2%, and 98.7% at 23 °C, −40 °C, and 50 °C, respectively. Pouch cells employing thin Li metal (50 μm) and high-loading sulfurized polyacrylonitrile (3.3 mAh cm −2 ) cathodes (negative-to-positive capacity ratio = 2) output 87.5% and 115.9% of their room temperature capacity at −40 °C and 50 °C, respectively. This work provides solvent-based design criteria for a wide temperature range Li-sulfur pouch cells.

25 ENERGY STORAGE↗
DOE OSTI2022

A Fiber-Based 3D Lithium Host for Lean Electrolyte Lithium Metal Batteries

3D hosts are promising to extend the cycle life of lithium metal anodes but have rarely been implemented with lean electrolytes thus impacting the practical cell energy density. To overcome this challenge, a 3D host that is lightweight and easy to fabricate with optimum pore size that enables full utilization of its pore volume, essential for lean electrolyte operations, is reported. The host is fabricated by casting a VGCF (vapor-grown carbon fiber)-based slurry loaded with a sparingly soluble rubidium nitrate salt as an additive. The network of fibers generates uniform pores of ≈3 µm in diameter with a porosity of 80%, while the nitrate additive enhances lithiophilicity. This 3D host delivers an average coulombic efficiency of 99.36% at 1 mA cm -2 and 1 mAh cm -2 for over 860 cycles in half-cell tests. Full cells containing an anode with 1.35-fold excess lithium paired with LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) cathodes exhibit capacity retention of 80% over 176 cycles at C/2 under a lean electrolyte condition of 3 g Ah -1 . This work provides a facile and scalable method to advance 3D lithium hosts closer to practical lithium-metal batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A low-cost sulfate-based all iron redox flow battery

Redox flow batteries (RFBs) are promising choices for stationary electric energy storage. Nevertheless, commercialization is impeded by high-cost electrolyte and membrane materials. Here, we report a low-cost all-iron RFB that features inexpensive FeSO 4 electrolytes, microporous membrane along with a glass fiber separator. The addition of 0.1 м 1-ethyl-3-methylimidazolium chloride (EMIC) overcomes the low solubility of FeSO 4 in water which is raised to 2.2 м. DFT calculations demonstrate that EMI + can strengthen the interaction between sulfate anions and water molecules. This electrolyte composition also allows both anode and cathode reactions to operate without actively maintaining a pH gradient between them, thus eliminating the need for expensive ion exchange membranes. The all-iron RFB demonstrates stable operation at a current density of 20 mA cm –2 for more than 800 cycles via a simple, periodic regeneration process. Furthermore, the system cost of FeSO 4 /EMIC RFBs is projected to be $ 50 per kWh due to its low-cost active materials and the inexpensive microporous membrane. Finally, this low-cost, high-concentration all-iron RFB is a promising stationary energy–storage system for storing renewable energy.

25 ENERGY STORAGE↗
DOE OSTI2021

Sub-nanometer confinement enables facile condensation of gas electrolyte for low-temperature batteries

Abstract Confining molecules in the nanoscale environment can lead to dramatic changes of their physical and chemical properties, which opens possibilities for new applications. There is a growing interest in liquefied gas electrolytes for electrochemical devices operating at low temperatures due to their low melting point. However, their high vapor pressure still poses potential safety concerns for practical usages. Herein, we report facile capillary condensation of gas electrolyte by strong confinement in sub-nanometer pores of metal-organic framework (MOF). By designing MOF-polymer membranes (MPMs) that present dense and continuous micropore (~0.8 nm) networks, we show significant uptake of hydrofluorocarbon molecules in MOF pores at pressure lower than the bulk counterpart. This unique property enables lithium/fluorinated graphite batteries with MPM-based electrolytes to deliver a significantly higher capacity than those with commercial separator membranes (~500 mAh g −1 vs. <0.03 mAh g −1 ) at −40 °C under reduced pressure of the electrolyte.

25 ENERGY STORAGE↗
DOE OSTI2021

Design and Optimization of the Direct Recycling of Spent Li-Ion Battery Cathode Materials

Direct regeneration of spent Li-ion batteries based on the hydrothermal relithiation of cathode materials is a promising next-generation recycling technology. In order to demonstrate the feasibility of this approach at a large scale, we systematically design and optimize the process parameters to minimize both energy and raw material costs. Specifically, the effects of regenerative processing parameters on the composition, structure, and electrochemical performance of the regenerated cathode materials are investigated via systematic characterization and testing. From this analysis, it was found that the raw material costs can be substantially reduced by either replacing the typically employed 4 M LiOH solution by a cost-effective mixture of 0.1 M LiOH and 3.9 M KOH or recycling of the concentrated 4 M LiOH for continuous relithiation processes. Finally, life cycle analysis suggests that this strategy results in reduced energy consumption and greenhouse gas emissions, leading to an increased potential revenue, particularly when compared with hydro- and pyrometallurgical recycling methods.

25 ENERGY STORAGE↗