Engineering topics

Homer, Eric R.

Publications and source records attributed to Homer, Eric R..

9 records

DOE OSTI2024

Grain boundary solute segregation across the 5D space of crystallographic character

Solute segregation in materials with grain boundaries (GBs) has emerged as a popular method to thermodynamically stabilize nanocrystalline structures. However, the impact of varied GB crystallographic character on solute segregation has never been thoroughly examined. Here, this work examines Co solute segregation in a dataset of 7272 Al bicrystal GBs that span the 5D space of GB crystallographic character. Considerable attention is paid to verification of the calculations in the diverse and large set of GBs. In addition, the results of this work are favorably validated against similar bicrystal and polycrystal simulations. As with other work, we show that Co atoms exhibit strong segregation to sites in Al GBs and that segregation correlates strongly with GB energy and GB excess volume. Segregation varies smoothly in the 5D crystallographic space but has a complex landscape without an obvious functional form.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Insights into factors that affect non-Arrhenius migration of a simulated incoherent Σ3 grain boundary

Non-Arrhenius grain boundary migration, sometimes referred to as antithermal migration where temperature and GB velocity values are inversely related to each other, is examined in an incoherent twin Σ3 [111] 60° (11 8 5) nickel grain boundary. Molecular dynamics is used to simulate migration and examine the effect of various factors on the migration, including interatomic potential, system size, driving force, and variation of atomic grain boundary structure. A classical model for grain boundary migration, in its unsimplified form, is used to analyze the results. The grain boundaries exhibit migration mechanisms with very low apparent barrier heights to migration. As a result, the boundaries migrate quickly but exhibit a velocity saturation similar to that of dislocations. Furthermore, the various interatomic potentials exhibit different migration velocities, but their similarities suggest they all predict similar overall behaviors of migration. The variation of atomic structure in the same incoherent twin grain boundary leads to diverse behaviors with barrier heights that vary from non-Arrhenius to Arrhenius migration. Facet nucleation is confirmed not to be a requirement for this boundary based on an examination of simulation cell size; however, the presence and/or interaction between numerous facets does suggest a slowing and increased barrier height to migration for larger boundaries.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Nanotwin stability in alloyed copper under ambient and cryo-temperature dependent deformation states

Nanometer size grains, solid solution strengthening, low temperatures, and a high density of nanotwins can provide significant strengthening to a material. Nevertheless, under loading the microstructure may evolve altering the effect of grain size, twin density, etc. on this strengthening. In some cases, these effects can be coupled as in detwinning, which is a mechanism for cryogenic grain growth. Here, in this work, a series of copper nanotwinned columnar grains are solid solution alloyed with aluminum and subject to ambient and cryogenic (–196 °C) environments during mechanical indentation, with the influence of alloying on the detwinning evolution studied. Under indentation, at a lower aluminum solute content (2 at.%), the columnar grains bent corresponding to a loss of twins. At a higher aluminum solute content (8 at.%), the grains shear and retain the nanotwins. Atomistic-scale simulations reveal an increase in the incoherent twin boundary velocity with decreasing temperature, but this boundary velocity is reduced with increasing alloy solute content. The coupling of solid solution strengthening and nanotwin stabilization is then used to explain the microstructural stability as a function of indentation at different temperature conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2022

A classical equation that accounts for observations of non-Arrhenius and cryogenic grain boundary migration

Observations of microstructural coarsening at cryogenic temperatures, as well as numerous simulations of grain boundary motion that show faster migration at low temperature than at high temperature, have been troubling because they do not follow the expected Arrhenius behavior. This work demonstrates that classical equations, that are not simplified, account for all these oddities and demonstrate that non-Arrhenius behavior can emerge from thermally activated processes. According to this classical model, this occurs when the intrinsic barrier energies of the processes become small, allowing activation at cryogenic temperatures. Additional thermal energy then allows the low energy process to proceed in reverse, so increasing temperature only serves to frustrate the forward motion. This classical form is shown to reconcile and describe a variety of diverse grain boundary migration observations.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Fundamental Mechanisms Controlling Dislocation-Obstacle Interactions in Metals and Alloys

This project combined modeling and experimentation across micro-meso-macro length scales to investigate the role of long-range internal stresses associated with obstacles and dislocation populations, in the deformation response of cubic metals. In addition to unique insights into the physical behavior of metals, advances were also made in modeling techniques and tools at the meso and atomistic level, and new characterization methods were developed and disseminated to the scientific community. Twenty eight journal papers, two dissertations and three theses have served as vehicles to share the gained scientific knowledge, and two open-source software packages have been developed, maintained and distributed. Additional publications are in progress.

36 MATERIALS SCIENCE↗

DOE OSTI2021

New Mechanism for Yield Point Phenomena

Yield point phenomena (YPP) are widely attributed to discrete dislocation locking by solute atmospheres. An alternate YPP mechanism was recently suggested by simulations of Ta single crystals without any influence of solutes or discrete dislocations. The general meso-scale (GM) simulations consist of crystal plasticity (CP) plus accounting for internal stresses of geometrically necessary dislocation content. GM predicted the YPP while CP did not, suggesting a novel internal stress mechanism. The predicted YPP varied with crystal orientation and boundary conditions, contrary to expectations for a solute mechanism. The internal stress mechanism was probed by experimentally deforming oligocrystal Ta samples and comparing the results with independent GM simulations. Strain distributions of the experiments were observed with high-resolution digital image correlation. A YPP stress–strain response occurred in the 0–2% strain range in agreement with GM predictions. Shear bands appeared concurrent with the YPP stress–strain perturbation in agreement with GM predictions. At higher strains, the shear bands grew at progressively slower rates in agreement with GM predictions. It was concluded that the internal stress mechanism can account for the existence of YPP in a wide variety of materials including ones where interstitial-dislocation interactions and dislocation transient avalanches are improbable. Furthermore, the internal stress mechanism is a CP analog of various micro-scale mechanisms of discrete dislocations such as pile-up or bow-out. It may operate concurrently with strain aging, or either mechanism may operate alone. A suggestion was made for a future experiment to answer this question.

42 ENGINEERING↗

DOE OSTI2021

Fundamental Mechanisms Controlling Dislocation-Obstacle Interactions in Metals and Alloys

This project combined modeling and experimentation across micro-meso-macro length scales to investigate the role of long-range internal stresses associated with obstacles and dislocation populations, in the deformation response of cubic metals. In addition to unique insights into the physical behavior of metals, advances were also made in modeling techniques and tools at the meso and atomistic level, and new characterization methods were developed and disseminated to the scientific community. Twenty eight journal papers, two dissertations and three theses have served as vehicles to share the gained scientific knowledge, and two opensource software packages have been developed, maintained and distributed. Additional publications are in progress.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Insights into grain boundary energy structure-property relationships by examining computed [100] disorientation axis grain boundaries in Nickel

A study of 346 computed [100] disorientation axis grain boundaries provides insight into grain boundary energy structure-property relationships. The grain boundaries come from 6 coincidence site lattice misorientations at regularly spaced disorientation angles, and cover the full range of boundary plane orientations. The computed energy has clear trends in disorientation angle and boundary plane orientation. Here, the data are used to reexamine the 'special' attribute frequently applied to low Σ coincidence site lattice misorientations and low-angle boundaries and to assess the accuracy of a face-centered cubic grain boundary energy function.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Slip band characteristics in the presence of grain boundaries in nickel-based superalloy

Shear strain profiles along slip bands in a modified Rolls-Royce nickel superalloy (RR1000) were analyzed for a tensile sample deformed by 2%. The strain increased with distance away from a grain boundary (GB), with maximum shear strain towards the center of the grain, indicating that dislocation nucleation generally occurred in the grain interior. The strain gradients in the neighborhood of the GBs were quantified and generally correlated with rotation about the active slip system line direction. This leads to an ability to determine the active slip system in these regions. The dislocation spacing and pileup stresses were inferred. The dislocation spacing closely follows an Eshelby analytical solution for a single ended pileup of dislocations under an applied stress. The distribution of pileup stress values for GBs of a given misorientation angle follows a log-normal distribution, with no correlation between the pileup stress and the GB misorientation angle. Furthermore, there is no observed correlation between various transmissivity factors and slip band pileup stress. Hence it appears that the obstacle strength of any of the observed GBs is adequate to facilitate the dislocation pileups present in the slip bands. However, slip band transmission does correlate with transmissivity factors, with the current study focusing on the Luster and Morris m’-factor. Observation of strain profiles of transmitted bands indicate dislocation nucleation locations.

36 MATERIALS SCIENCE↗