Search NASA⌕ Search

Engineering topics

Honda, Y

Publications and source records attributed to Honda, Y.

A Comprehensive Study of Nanometer Resolution of the IPBPM at ATF2

High-resolution beam position monitors (IPBPMs) have been developed in order to measure the electron beam position at the focus point of ATF2 to a few nanometers in the vertical plane. To date, the IPBPM system has operated in test mode with a highest demonstrated resolution of 8.7 nm in the ATF extraction line during 2008. After expected noise source calculations there still remains 7.9 nm of noise of unexplained origin. We summarize the experimental work on the IPBPM system since this measurement and outline the possible origins of these sources. We then present a study plan to be performed at the ATF2 facility designed to identify and to improve the resolution performance and comment on the expected ultimate resolution of this system. The Accelerator Test Facility 2 (ATF2) is a test beamline for ILC final focus system in the framework of the ATF international collaboration which was constructed to extend the extraction line at ATF, located at KEK, Japan. There are two goals of the ATF2: firstly to demonstrate focusing to 37 nm vertical beam size, secondly to achieve a few nanometer level beam orbit stability at the focus point in the vertical plane. High-resolution beam position monitors (IPBPMs) for the interaction point (IP) have been developed in order to measure the electron beam position at the focus point of the ATF2 to a few nanometers in the vertical plane. The previous measured position resolution of IPBPMs was 8.7 nm for a 0.68 x 10{sup 10} e/bunch beam with a dynamic range of 5 {mu}m. The intrinsic noise of the system was estimated to be 2.6 nm at 10{sup 10} e/bunch. It is scaled to 3.8 nm at 0.68 x 10{sup 10} e/bunch which means that 7.9 nm of unknown noise remains. The origin of the unknown noise must be studied in order to improve the resolution. This paper describes the ongoing work to improve the resolution of IPBPMs.

43 PARTICLE ACCELERATORS↗

Spontaneous formation of highly regular superlattice structure in InGaN epilayers grown by molecular beam epitaxy

In this letter, we have investigated the structural properties of thick InGaN layers grown on GaN by plasma-assisted molecular beam epitaxy, using two growth rates of 1.0 and 3.6 A/s. A highly regular superlattice (SL) structure is found to be spontaneously formed in the film grown at 3.6 A/s but not in the film grown at 1.0 A/s. The faster grown film also exhibits superior structural quality, which could be due to the surface roughness suppression caused by kinetic limitation, and the inhibition of the Frank-Read dislocation generation mechanism within the spontaneously formed SL structure.

36 MATERIALS SCIENCE↗

Development of an electron gun for an ERL based light source in Japan

We have developed a prototype DC photoemission electron gun for a future energy recovery linac (ERL) based light source in Japan. The prototype gun is operated at up to 250 kV and is designed to deliver up to 50 mA beam current. A diagnostic beam line for emittance and bunch length measurements has been constructed. We have also designed a new 500 kV DC gun which is capable of producing up to 10 mA electron current with emittance lower than 1 mm-mrad. The high voltage terminal will be isolated by ten ceramics stacked in series. The new gun will satisfy performance required as an injector for the compact ERL, which will be constructed at KEK site as a prototype of the future ERL light source.

43 PARTICLE ACCELERATORS↗

ILC Positron Source Based on Laser Compton

Positron generation is one of the most difficult technical challenges among the ILC (International Linear Collider) subsystems. A positron source based on Laser Compton back scattering is an attractive and advanced option for the ILC positron source. Here, the positrons are generated, via the pair creation process, from high energy gamma rays which themselves are produced by Compton scattering of laser photons off a high-energy electron beam. Polarized positrons can be generated by employing a circularly polarized laser. The positron polarization is easily controlled and switched by changing the laser polarity. The electron beam can be unpolarized. The required electron energy is only a few GeV (in contrast, the ''undulator scheme'', another advanced option, requires at least 100 GeV or more) and the system can be prototyped and tested prior to the real construction. The laser Compton technology has many other applications like advanced X-ray sources and a good synergy is expected. In addition, this technology can be a powerful driving force for the ILC project attracting many researchers from outside the ILC community. The ILC positron source is a technical challenge and it will be realized only if the latest technologies are integrated seamlessly with the necessary R and D efforts for system specific issues. The latest technologies include high power lasers, high brightness electron beams, high finesse optical cavities for as laser-beam interaction point, etc. We present the design status and the related experimental efforts for the ILC positron source based on Laser Compton scattering. The respective advantages of various options for the electron beam (based on Linac, storage ring, and ERL) are also compared.

43 PARTICLE ACCELERATORS↗