Engineering topics

Hooker, John R.

Publications and source records attributed to Hooker, John R..

5 records

NASA NTRS2017

Commercial Cargo Derivative Study of the Advanced Hybrid Wing Body Configuration with Over-Wing Engine Nacelles

LM has leveraged our partnership with the Air Force Research Laboratory (AFRL) and NASA on the advanced hybrid wing body (HWB) concept to develop a commercial freighter which addresses the NASA Advanced Air Transport Technology (AATT) Project goals for improved efficiency beyond 2025. The current Air Force Research Laboratory (AFRL) Revolutionary Configurations for Energy Efficiency (RCEE) program established the HWB configuration and technologies needed for military transports to achieve aerodynamic and fuel efficiencies well beyond the commercial industry's most modern designs. This study builds upon that effort to develop a baseline commercial cargo aircraft and two HWB derivative commercial cargo aircraft to quanitify the benefit of the HWB and establish a technology roadmap for further development.

Hooker, John R.↗

NASA NTRS2017

Transonic Semispan Aerodynamic Testing of the Hybrid Wing Body with Over Wing Nacelles in the National Transonic Facility

A wind tunnel investigation of a 0.04-scale model of the Lockheed Martin Hybrid Wing Body (HWB) with Over Wing Nacelles (OWN) air mobility transport configuration was conducted in the National Transonic Facility at the NASA Langley Research Center under a collaborative partnership between NASA, the Air Force Research Laboratory, and Lockheed Martin Aeronautics Company. The wind tunnel test sought to validate the transonic aerodynamic performance of the HWB and to validate the efficiency benefits of the OWN installation as compared to the traditional under-wing installation. The semispan HWB model was tested in a clean wing configuration and also tested with two different nacelles representative of a modern turbofan engine and a future advanced high bypass ratio engine. The nacelles were installed in three different locations with two over-wing positions and one under-wing position. Five-component force and moment data, surface static pressure data, and aeroelastic deformation data were acquired. For the cruise configuration, the model was tested in an angle-of-attack range between -2 and 10 degrees at free-stream Mach numbers from 0.3 to 0.9 and at unit Reynolds numbers between 8 and 39 million per foot, achieving a maximum of 80% of flight Reynolds numbers across the Mach number range. The test results validated pretest computational fluid dynamic (CFD) simulations of the HWB performance including the OWN benefit and the results also exhibited excellent transonic drag data repeatability to within +/-1 drag count. This paper details the experimental setup and model overview, presents some sample data results, and describes the facility improvements that led to the success of the test.

Chan, David T.↗

NASA NTRS1997

Static Aeroelastic Analysis of Transonic Wind Tunnel Models Using Finite Element Methods

A computational method for accurately predicting the static aeroelastic deformations of typical transonic transport wind tunnel models is described. The method utilizes a finite element method (FEM) for predicting the deformations. Extensive calibration/validation of this method was carried out using a novel wind-off wind tunnel model static loading experiment and wind-on optical wing twist measurements obtained during a recent wind tunnel test in the National Transonic Facility (NTF) at NASA LaRC. Further validations were carried out using a Navier-Stokes computational fluid dynamics (CFD) flow solver to calculate wing pressure distributions about several aeroelastically deformed wings and comparing these predictions with NTF experimental data. Results from this aeroelastic deformation method are in good overall agreement with experimentally measured values. Including the predicted deformations significantly improves the correlation between CFD predicted and experimentally measured wing & pressures.

Hooker, John R.↗

NASA NTRS1992

Spatial and temporal adaptive procedures for the unsteady aerodynamic analysis of airfoils using unstructured meshes

An algorithm which combines spatial and temporal adaption for the time integration of the two dimensional Euler equations on unstructured meshes of triangles is presented. Spatial adaption involves mesh enrichment to add elements in high gradient regions of the flow and mesh coarsening to remove elements where they are no longer needed. Temporal adaption is a time accurate, local time stepping procedure which integrates the flow equations in each cell according to the local numerical stability constraint. The flow solver utilizes a four stage Runge-Kutta time integration scheme with an upwind flux-split spatial discretization. Results obtained using spatial and temporal adaption indicate that highly accurate solutions can be obtained with a significant savings of computing time over global time stepping.

Hooker, John R.↗

NASA NTRS1992

Spatial and temporal adaptive procedures for the unsteady aerodynamic analysis of airfoils using unstructured meshes

An algorithm which combines spatial and temporal adaption for the time integration of the two-dimensional Euler equations on unstructured meshes of triangles is presented. Spatial adaption involves mesh enrichment to add elements in high gradient regions of the flow and mesh coarsening to remove elements where they are no longer needed. Temporal adaption is a time accurate, local time stepping procedure which integrates the flow equations in each cell according to the local numerical stability constraint. The flow solver utilizes a four-stage Runge-Kutta time integration scheme with an upwind flux-split spatial discretization. Results obtained using spatial and temporal adaption indicate that highly accurate solutions can be obtained with a significant savings of computing time over global time stepping.

Hooker, John R.↗