Search NASA⌕ Search

Engineering topics

Hopkinson, David

Publications and source records attributed to Hopkinson, David.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Effect of Power Plant Capacity on the CAPEX, OPEX, and LCOC of the CO2 Capture Process in Pre-Combustion Applications - Abstract

Aspen Plus v8.8 was used to simulate the pre-combustion CO2 capture process from a typical fuel gas stream at different power plant capacities ranging from 54.3 to 543 MW. Polyethylene glycol polydimethyl siloxane (PEGPDMS-1) was used as a physical solvent to capture CO2 in a countercurrent packed-bed absorber containing a structured packing (Mellapak 250Y). The process pressure was 51.4 bar and the solvent temperature was varied from 10 to 40 <sup>o</sup>C. The internal diameter of the absorber ranged from 1.9 to 7 m and the packing height from 13.9 to 45.5 m. The physico-chemical properties were obtained and modeled using the Perturbed Chain-Statistical Associating Fluid Theory (PC-SAFT) Equation-of-State (EOS).<p> Four process constraints were imposed in Aspen Plus: (1) no flooding in the absorber, (2) the absorber height to diameter ratio (H/D) is greater than or equal 6, (3) at least 90 mol% of the CO2 capture from the fuel gas stream, and (4) the CO2 stream destined to sequestration sites should contain less than 600 ppm water concentration and less than or equal 0.5 mol% of fuel gases (H2, CO, CH4). The plant lifetime was assumed to be 30 years with an annual discount rate of 10% and an annual maintenance cost of 4% of the total capital expenses.</p><p> Seven power plants with different capacities were used and for each plant, the corresponding CO2 capture process was simulated. The absorber flooding was checked using the generalized pressure drop correlation (GPDC) by Leva [1] and the capital expenditure (CAPEX), operating expenditure (OPEX), and levelized costs per ton of CO2 captured (LCOC) were calculated [2-5]. Normalized by the largest power plant capacity (543 MW) used in the simulation, the results indicated that the capital and operating expenditures increased, however, the LCOC decreased with increasing plant capacity. This behavior was due to the increased annual tonnage of the CO2 captured with plant capacity as shown in Figure 1. The calculated CAPEX, OPEX, LCOC and the tonnage of CO2 captured for the 543 MW power plant were about 52 MM$, 22 MM$/year, 7.46 $/ton and 4 MM ton/year.</p>

Ashkanani, Husain↗
DOE OSTI2020

Alkylamine Incorporation in Amidoxime Functionalized Polymers of Intrinsic Microporosity for Gas Capture and Separation

Amidoxime functionalized polymers of intrinsic microporosity (PIMs) are synthesized from postsynthetic functionalization of PIM‐1 with hydroxylamine and processed into chemisorbents with alkylamine incorporation. Strong interaction between functionalized PIM‐1 and primary amines is characterized in detail by diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) study. As‐prepared sorbents not only show the highest CO 2 uptake capacity (37.9 cm 3 g −1 at 0.15 bar and 298 K) recorded in reported PIMs, but they also demonstrate tunable, processable, and stable polymeric sorbent design, which can be nanoengineered for other gas capture and separation applications.

Miles, Ashley↗
DOE OSTI2020

Levelized Cost of CO 2 Captured Using Five Physical Solvents in Pre-combustion Applications

Aspen Plus v8.8 was used to perform techno-economic analysis (TEA) of a CO 2 capture process from a typical fuel gas stream in a 543-MW pre-combustion power plant using five different physical solvents (Selexol, PEGPDMS-1, NMP, [aPy][Tf 2 N] and [hmim][Tf 2 N]). The process included a countercurrent packed-bed absorber operating under high-pressure over a wide range of temperatures and three pressure-swing flash drums for solvent regeneration. Furthermore, two packings, Mellapak 250Y and IMTP50, were used and the Levelized costs of CO 2 captured (LCOC) were calculated. The simulation results indicated that using Mellapak 250Y exhibited lower LCOC values than those when using IMTP50 for the five solvents under all conditions used as it offered better mass transfer. The CO 2 capture process carried out at low temperatures showed lower LCOC values than those at higher temperatures due to the increased CO 2 solubility in the solvents at lower temperatures, requiring smaller absorber diameter and lower solvent circulation rates, which offset the cooling requirements. Comparing the lowest LCOC values for the five solvents, the hydrophobic PEGPDMS-1 solvent was the most promising one compared to the other four solvents, due to its lowest capital and operating costs and noncorrosive, which enabled using less expensive materials for the process equipment.

42 ENGINEERING↗
DOE OSTI2020

Cross-Linked Polyphosphazene Blends as Robust CO2 Separation Membranes

An effective cross-linking technique allows a viscous, highly gas permeable hydrophilic polyphosphazene to be cast as solid membrane films. By judicious blending with other polyphosphazenes to improve mechanical properties, a membrane exhibiting the highest CO2 permeability (610 barrer) combined with good CO2/N2 selectivity (35) among polyphosphazenes is described here. The material demonstrates performance stability after 500 hours of exposure to a coal-fired power plant flue gas, making it attractive for use in carbon capture applications. Its CO2/N2 selectivity under conditions up to full humidity is also stable, and although the gas permeability does decline, the performance is fully recovered upon drying. The high molecular weight of these heteropolymers also allows them to be cast as a thin selective layer on an asymmetric porous membrane, yielding CO2 permeance of 1200 GPU, CO2/N2 pure gas selectivity of 31, which does not decline over 2000 hours due to physical aging. In addition to gas separation membranes, this cross-linked polyphosphazene can potentially be extended to other applications such as drug delivery or proton exchange membranes which take advantage of the polyphosphazene’s versatile chemistry.

Kusuma, Victor↗
DOE OSTI2020

Radiation-resistant metal-organic framework enables efficient separation of krypton fission gas from spent nuclear fuel

Capture and storage of volatile radionuclides that result from processing of used nuclear fuel is a major challenge. Solid adsorbents, in particular ultra-microporous metal-organic frameworks, could be effective in capturing these volatile radionuclides, including 85 Kr. However, metal-organic frameworks are found to have higher affinity for xenon than for krypton, and have comparable affinity for Kr and N 2 . Also, the adsorbent needs to have high radiation stability. To address these challenges, here we evaluate a series of ultra-microporous metal-organic frameworks, SIFSIX-3-M (M = Zn, Cu, Ni, Co, or Fe) for their capability in 85 Kr separation and storage using a two-bed breakthrough method. These materials were found to have higher Kr/N 2 selectivity than current benchmark materials, which leads to a notable decrease in the nuclear waste volume. The materials were systematically studied for gamma and beta irradiation stability, and SIFSIX-3-Cu is found to be the most radiation resistant.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Amino acids react with carbon dioxide (CO2) and form nanofibers and nanoflowers

A method for capturing CO2 comprising dissolving at least one pure amino acid (AA) in water without the use of a catalyst for establishing protonation of an amino group of the amino acid, adding at least one base solution to the amino acid and water solution to deprotonate the protonated amino group of the amino acid and forming an amino acid-XOH—H2O wherein X is sodium or potassium, and subjecting CO2 to the amino acid-XOH—H2O to form new nanomaterials is provided. A regenerable nanofiber is disclosed comprising a NaHCO3 nanofiber, a KHCO3 nanofiber, or an amino acid nanofiber made from subjecting a CO2 gas to an amino acid aqueous solvent. Preferably, the amino acid aqueous solvent is one or more of a Gly-NaOH—H2O, an Ala-NaOH—H2O, a Phe-NaOH—H2O, a Gly-KOH—H2O, an Ala-KOH—H2O, and a Phe-KOH—H2O.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Foaming Dependence on the Interface Affinities of Surfactant-like Molecules

We have explored the relationship between physical properties and foaming behavior of 30 wt % aqueous monoethanolamine (MEA) solutions with three different surfactant-like additives. The additives included one commercial surfactant, cetyltrimethylammonium bromide (CTAB), and two CO 2 capture catalysts that behave as weak surfactants. The physical properties of interest were the additives’ affinity for the liquid–vapor interface and the viscosity, surface tension, and surface elasticity of the solutions. The physical properties were explored using molecular dynamics simulations as well as experiments. The additives’ affinity for the liquid–vapor interface played a key role in the foaming behavior by affecting the interfacial properties (surface tension and surface elasticity) of the aqueous MEA solutions. The solution containing CTAB showed the largest surface tension depression and the largest surface elasticity and resulted in the largest amount of foaming. The two catalyst solutions had almost similar surface tensions but differed in their elasticity. Here, the catalyst solution with higher surface elasticity showed more foaming due to higher foam stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗