Engineering topics

Horner, Garnett C.

Publications and source records attributed to Horner, Garnett C..

7 records

NASA NTRS2001

A Cryogenic Magnetostrictive Actuator using a Persistent High Temperature Superconducting Magnet, Part 1: Concept and Design: Concept and Design - Part 1

Cryogenic magnetostrictive materials, such as rare earth zinc crystals, offer high strains and high forces with minimally applied magnetic fields, making the material ideally suited for deformable optics applications. For cryogenic temperature applications, such as Next Generation Space Telescope (NGST), the use of superconducting magnets offer the possibility of a persistent mode of operation, i.e., the magnetostrictive material will maintain a strain field without power. High temperature superconductors (HTS) are attractive options if the temperature of operation is higher than 10 degrees Kelvin (K) and below 77 K. However, HTS wires have constraints that limit the minimum radius of winding, and even if good wires can be produced, the technology for joining superconducting wires does not exist. In this paper, the design and capabilities of a rare earth zinc magnetostrictive actuator using bulk HTS is described. Bulk superconductors can be fabricated in the sizes required with excellent superconducting properties. Equivalent permanent magnets, made with this inexpensive material, are persistent, do not require a persistent switch as in HTS wires, and can be made very small. These devices are charged using a technique which is similar to the one used for charging permanent magnets, e.g., by driving them into saturation. A small normal conducting coil can be used for charging or discharging. Very fast charging and discharging of HTS tubes, as short as 100 microseconds, has been demonstrated. Because of the magnetic field capability of the superconductor material, a very small amount of superconducting magnet material is needed to actuate the rare earth zinc. In this paper, several designs of actuators using YBCO and BSCCO 2212 superconducting materials are presented. Designs that include magnetic shielding to prevent interaction between adjacent actuators will also be described. Preliminary experimental results and comparison with theory for BSSCO 2212 with a magnetostrictive element will be discussed.

Horner, Garnett C.↗

NASA NTRS1999

Single Axis Piezoceramic Gimbal

This paper describes the fabrication, testing, and analysis of a single axis piezoceramic gimbal. The fabrication process consist of pre-stressing a piezoceramic wafer using a high-temperature thermoplastic polyimide and a metal foil. The differential thermal expansion between the ceramic and metal induces a curvature. The pre-stressed, curved piezoceramic is mounted on a support mechanism and a mirror is attached to the piezoceramic. A plot of gimbal angle versus applied voltage to the piezoceramic is presented. A finite element analysis of the piezoceramic gimbal is described. The predicted gimbal angle versus applied voltage is compared to experimental results.

Horner, Garnett C.↗

NASA NTRS1994

Joint for a variable geometry truss and method of constructing same

A joint and a method of constructing a joint for a variable geometry truss having a variable number of planes of variable length battens connected together in a triangular configuration, each plane being connected by six fixed length longerons in a Stewart platform configuration, are presented. The variable length battens allow the orientation of one end plane of the variable geometry truss to be changed to the other end plane in a controlled manner by selectively adjusting the lengths of the variable length battens. A main pivot joint pivotally connects two battens about a pivotal axis. A universal joint is pivotally connected to the main joint such that the pivotal axis of the universal joint is coextensive with the pivotal axis at the main joint. Two longerons are pivotally connected to the universal joint. Each longeron is thereby provided with three intersecting axes of rotation. Each longeron may include a revolute joint, allowing rotation about the longitudinal axis of the longeron.

Horner, Garnett C.↗

NASA NTRS1989

A survey of experiments and experimental facilities for active control of flexible structures

A brief survey of large space structure control related experiments and facilities was presented. This survey covered experiments performed before and up to 1982, and those of the present period (1982-...). Finally, the future planned experiments and facilities in support of the control-structure interaction (CSI) program were reported. It was stated that new, improved ground test facilities are needed to verify the new CSI design techniques that will allow future space structures to perform planned NASA missions.

Sparks, Dean W., Jr.↗

NASA NTRS1988

System identification in the microcomputer environment

An implementation of an algorithm for system identification, the eigenvalue realization algorithm (ERA), on a microcomputer is reported. Test results are presented to show that accurate structural identification can be performed in a microcomputer environment. It is also shown that the memory limits (640 K) of small machines are generally adequate for solving large scale problems (e.g., Hankel matrices with 15,000 elements), with run times being on the order of several minutes.

Garcia, Ephrahim↗

NASA NTRS1987

Microprocessor controlled proof-mass actuator

The objective of the microprocessor controlled proof-mass actuator is to develop the capability to mount a small programmable device on laboratory models. This capability will allow research in the active control of flexible structures. The approach in developing the actuator will be to mount all components as a single unit. All sensors, electronic and control devices will be mounted with the actuator. The goal for the force output capability of the actuator will be one pound force. The programmable force actuator developed has approximately a one pound force capability over the usable frequency range, which is above 2 Hz.

Horner, Garnett C.↗

NASA NTRS1986

Analysis and simulation of the MAST (COFS-1 flight hardware)

In-house analysis work in support of the Control of Flexible Structures (COFS) program is being performed at the NASA Langley Research Center. The work involves evaluation of the proposed design configuration, controller design as well as actuator dynamic modeling, and MAST/actuator dynamic simulation of excitation and damping. A complete finite element model of the MAST has been developed. This finite element model has been incorporated into an optimization procedure which minimizes total mass while maintaining modal coupling. Results show an increase in the total mass due to additional constraints (namely, the diagonal frequency constraint) imposed on the baseline design. A valid actuator dynamic model is presented and a complete test sequence of the proposed flight experiment is demonstrated. The actuator dynamic model is successfully used for damping and the stroke limitations for first mode excitation are demonstrated. Plans are to incorporate additional design variables and constraints into the optimization procedure (such as actuator location) and explore alternative formulations of the objective function. A different actuator dynamic model to include hardware limitations will be investigated.

Horta, Lucas G.↗