Search NASA⌕ Search

Engineering topics

Hosemann, Peter

Publications and source records attributed to Hosemann, Peter.

At least 73 records · Page 4

Electrical properties of thermal oxide scales on pure iron in liquid lead-bismuth eutectic

Here, the impedance behavior of pre-oxidized iron in liquid lead-bismuth eutectic (LBE) at 200 °C is studied using electrochemical impedance spectroscopy. The structures and resistance of oxide grown on iron oxidized in air at different temperatures and durations are compared. The results show that the resistance of the oxide film increases with increasing oxidizing temperature, due to the formation of a thicker scale and fewer defects. At the same temperature (600 °C), increasing the oxidation time can also reduce the defect concentration in the oxide film and improve the impedance of the oxide scale in LBE.

42 ENGINEERING↗

Status Report on Development of a Cask to Enable Pulsed Neutron Characterization of Irradiated Fuel

We present the design of a shielding cask that allows pulsed neutron characterization of irradiated fuel rodlets prior to their destructive examination in hot cells. The goal is to provide complementary and informative measurements that will inform subsequent hot cell PIE examinations by identifying typical and atypical regions with respect to microstructure, tomographic data, or isotope densities. Time-of-flight neutron diffraction has the potential to offer efficient, non-destructive and non-contact microstructural characterization of irradiated fuel pins with spatial resolution of 1 mm3 to 1 cm3 while for energy-resolved neutron imaging (and by extension tomography) a resolution of 100 μm was demonstrated. The potential results include crystallinity vs. amorphous volumes and microstructural information such as phase compositions and textures from the diffraction data as well as distances (e.g. pellet to cladding), cracks, and isotopic distributions of minor actinides, fission products as well as fission gas partial pressures e.g. in the plenum from energy resolved neutron imaging. The capability will identify regions of atypical behavior and provide cost effective bulk characterization of entire samples prior to destructive evaluation in hot cells. This effort is a collaboration between LANL, INL, ORNL, and UC Berkeley. A key facet of the initiative is the ability to cost effectively ship irradiated fuels from INL to the pulsed spallation neutron source at LANSCE. The irradiated fuel would be loaded in the custom designed cask (designated RaMHaM) at INL hot cells which then could be shipped in a BRR Type B shipment container between INL and LANL. No hot cell is required after the loading of the sample at INL in the pathway laid out in this report, greatly simplifying handling at LANL.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Experimental methodology and theoretical framework in describing constrained plastic flow of FCC microscale tensile specimens

Small scale mechanical testing (SSMT) allows for the quantification of the mechanical responses for microscale and nanoscale material volumes. It has significant potential in improving our fundamental understanding of plastic deformation and in providing an engineering solution for testing complex and/or critical materials. Importantly, previous studies have revealed that plastic intermittency, manifested as strain bursts, are characteristic of the plastic flow behavior at the small length scale. In this work, interfacial constraint has been utilized to suppress strain bursts in order to stabilize plasticity. A new parameter, blocked volume ratio (BVR), is introduced to quantify the degree of constraint for a microscale specimen due to an interface. Here, we showed that the plastic flow behavior in FCC Ni-based metals is highly dependent on the BVR of the specimen.

36 MATERIALS SCIENCE↗

Chemical manipulation of hydrogen induced high p-type and n-type conductivity in Ga 2 O 3

Advancement of optoelectronic and high-power devices is tied to the development of wide band gap materials with excellent transport properties. However, bipolar doping (n-type and p-type doping) and realizing high carrier density while maintaining good mobility have been big challenges in wide band gap materials. Here P-type and n-type conductivity was introduced in β-Ga 2 O 3 , an ultra-wide band gap oxide, by controlling hydrogen incorporation in the lattice without further doping. Hydrogen induced a 9-order of magnitude increase of n-type conductivity with donor ionization energy of 20 meV and resistivity of 10 -4 Ω.cm. The conductivity was switched to p-type with acceptor ionization energy of 42 meV by altering hydrogen incorporation in the lattice. Density functional theory calculations were used to examine hydrogen location in the Ga 2 O 3 lattice and identified a new donor type as the source of this remarkable n-type conductivity. Positron annihilation spectroscopy measurements confirm this finding and the interpretation of the experimental results. This work illustrates a new approach that allows a tunable and reversible way of modifying the conductivity of semiconductors and it is expected to have profound implications on semiconductor field. At the same time, it demonstrates for the first time p-type and remarkable n-type conductivity in Ga 2 O 3 which should usher in the development of Ga 2 O 3 devices and advance optoelectronics and high-power devices.

36 MATERIALS SCIENCE↗

High operating temperature heat transfer fluids for solar thermal power generation. Final report

This is the final technical report for the DOE MURI project on developing high-operating temperature heat transfer fluids for solar thermal power generation. This project aimed to evaluate liquid metals as a heat-transport fluid and potential energy storage medium for concentrated solar powered (CSP) systems. The project consisted of five phases, starting with fluid selection and screen and ending with potential CSP integration. The initial fluid selection arrived at heavy liquid metals as candidate fluids such as lead bismuth eutectic (LBE) as the prime liquid-alloy candidate to be studied, given the conditions above. Fifty-seven liquid compositions were initially identified with liquidus temperatures lower than 200°C, composed of elements that provide no driving force to the reduction of Cr 2 O 3 or Al 2 O 3 passivation layers in pipe material which is required for corrosion prevention. LBE was identified as the primary candidate fluid after these compositions were compared against computational thermodynamic modeling to screen all of the selected systems that would be compatible with our design objectives. Twenty-eight of these compositions were also investigated with the rapid characterization methods; the accuracies of the liquidus temperature and the specific heats predicted by the computations were better than 3 percent and 9 percent, respectively. We conducted numerus corrosion tests of various Fe-Cr-Al based steels in LBE and its variants at temperate as high as 800°C. It was found that minor additions to the liquid did not provide sufficient corrosion protection to warrant their use in real applications. Furthermore, we investigated the detailed mechanism of corrosion between heavy liquid metal and the pipe material at these very high temperatures. A liquid metal loop was constructed to operate at these high temperatures. The loop construction and operation lead to valuable lessons learned that will be needed for industrial scale loops. Furthermore, we learned that electromagnetic pumps at these extreme temperatures will have to be reengineered and redesigned to be used for CSP applications.

14 SOLAR ENERGY↗

Key mechanistic features of swelling and blistering of helium-ion-irradiated tungsten

In this study, helium-ion-induced swelling and blistering of single-crystal tungsten is investigated using a Helium Ion Microscope for site-specific dose-controlled irradiation (at 25 keV) with analysis by Helium Ion Microscopy, Atomic Force Microscopy and Transmission Electron Microscopy (cross-sectioning by Focused Ion Beam milling). We show that the blister cavity forms at a depth close to the simulated helium peak and that nanobubbles coalesce to form nanocracks within the envelope of the ion stopping range, swelling the blister shell. These results provide the first direct experimental evidence for the interbubble fracture mechanism proposed in the framework of the gas pressure model for blister formation.

36 MATERIALS SCIENCE↗

Correlating high temperature mechanical and tribological properties of CrAlN and CrAlSiN hard coatings

CrAlN and CrAlSiN hard coatings deposited by magnetron sputtering were analyzed for their high temperature mechanical and tribological properties. High temperature nanoindentation measurements on both coatings were performed from room temperature up to 700 °C in steps of 100 °C where a reduction in hardness H and elastic modulus E* from their initial values was noticed. In addition, high temperature tribological tests were conducted in inert atmosphere in the same temperature range to obtain information about the coefficient of friction and the wear coefficient. In order to link the tribological behavior to the obtained mechanical properties, the H/E* ratio was calculated and compared to the high temperature wear from the current and other studies with similar coatings. Finally, the evolution of the mechanical and tribological properties at high temperature is discussed based on the current knowledge available in literature.

Drnovšek, Aljaž↗

Elevated temperature microcantilever testing of fresh U-10Mo fuel

Proliferation concerns are the driving force to reduce the enrichment of research reactor fuel from highly enriched fuel to lower levels of enriched fuel. One promising fuel alloy that would enable a reduction in enrichment without greatly diminishing fuel performance is Uranium with 10 wt. % Molybdenum (U-10 wt-% Mo). While there is a large amount of data available on the microstructure and thermal properties of this new fuel type currently there is insufficient data available on the mechanical properties. Small scale mechanical testing techniques can be used to evaluate the mechanical properties of the as-fabricated U-10 wt% Mo components at their intended operating temperature which should improve the accuracy of the input parameters employed by modelers. In this study the mechanical properties of a U-10 wt% Mo fuel meat sample taken from an as-fabricated fuel plate for a new fuel design were evaluated using in-situ scanning electron microscopy microcantilever testing under varying temperatures between room temperature and 200 °C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Plasticity of UO 2 studied and quantified via elevated temperature micro compression testing

Small scale mechanical testing has many beneficial features including the ability to sample the properties of a single crystal over a wide temperature range. Here, this manuscript presents the results of high temperature, in-situ scanning electron microscope microcompression testing of a single crystal of UO 2 . Observations indicated that the UO 2 microcompression specimens deformed in a ductile fashion at temperatures of 350 °C and above. The slip traces on the micro-compression specimens after deformation appeared on the {100}1/2<110> system at the temperatures and orientation tested. Finally, the Peierls stress of UO 2 is calculated using the microcompression data.

36 MATERIALS SCIENCE↗

Micropillar compression response of femtosecond laser-cut single crystal Cu and proton irradiated Cu

Femtosecond laser cutting has been used to fabricate micro- and mesoscale specimens for mechanical testing, but the impact on mechanical properties has not been fully evaluated. Micropillars of assorted sizes were fabricated in a single crystal Cu specimen and Cu irradiated to 1.4 peak displacements per atom using a femtosecond laser cutting system followed by focused ion beam milling to a final dimension of 7 μm x 7 μm x 12 μm. Microcompression testing showed that removing 5 μm of material from the laser cut surface in both specimens resulted in similar behavior to purely focused ion beam milled micropillars.

36 MATERIALS SCIENCE↗

Manufacturing Oxide Dispersion-Strengthened (ODS) Steel Fuel Cladding Tubes Using the Cold Spray Process

The cold spray materials deposition process has been explored for manufacturing oxide dispersion-strengthened (ODS) steel fuel cladding tubes. Gas-atomized 14YWT ODS steel powder was used as the feedstock material. A parametric investigation of the cold spray process involving substrate materials of various hardnesses, gas preheat temperatures, and carrier gas compositions was performed to gain the highest quality deposit. The high-velocity impact of the powder on the substrate led to dissolution of discrete oxide nanoparticles, which subsequently reprecipitated during postdeposition annealing at high temperatures. The tubes were manufactured by deposition on an Al-alloy mandrel substrate and subsequent chemical dissolution of the substrate. A 204-mm-long and 1-mm-thick ODS steel cladding tube was successfully manufactured. The grain growth and distribution of oxide nanoparticles in ferritic steel matrix were identified at elevated temperatures. In general, the cold spray process holds considerable promise for rapid, cost-effective manufacturing of ODS steel cladding tubes.

36 MATERIALS SCIENCE↗

The Application of the OPTICS Algorithm to Cluster Analysis in Atom Probe Tomography Data

Atom probe tomography (APT) is a powerful technique to characterize buried 3D nanostructures in a variety of materials. Accurate characterization of those nanometer-scale clusters and precipitates is of great scientific significance to understand the structure-property relationships and the microstructural evolution. The current widely used cluster analysis method, a variant of the DBSCAN algorithm, can only accurately extract clusters of the same atomic density, neglecting several experimental realities, such as density variations within and between clusters and the non-uniformity of the atomic density in the APT reconstruction itself (e.g. crystallographic poles and other field evaporation artifacts). The clustering results of DBSCAN-like method rely heavily on multiple input parameters, but ideal selection of those parameters is challenging and oftentimes ambiguous. In this study, we present a new cluster analysis method consisting of a well-known algorithm, called OPTICS, and a cluster extraction algorithm we developed to enable accurate detection of clusters of varying atomic density in APT data. The new method requires only one free parameter, and other inputs can be estimated based on physical parameters of the material. The effectiveness of this method is demonstrated by application to several small-scale model datasets and a real APT dataset obtained from an oxide-dispersion strengthened ferritic alloy specimen. The method’s sensitivity with respect to parameter selection is discussed and compared with the current widely used methods.

atom probe tomography, cluster analysis, density-b↗

Developing a Macro-scale SiC-cladding Behavior Model Based on Localized Mechanical and Thermal Property Evaluation on Pre- and Post-Irradiation SiC-SiC Composites (Final Report)

Silicon carbide is being investigated for accident tolerant fuel cladding applications due to its good neutronic performance, high temperature strength, exceptional stability under irradiation, and reduced oxidation compared to Zircaloy under accident conditions. The development and investigation of these materials is particularly important in the light of the Fukushima event and subsequent emphasis in DOE on accident tolerant fuel (ATF) concepts. In this work, we propose to develop and improve upon existing small-scale mechanical and thermal characterization methods, including micro-cantilever bend tests and fiber push-out tests, and time-domain thermo-reflectance measurements. These techniques will be applied to evaluate micro-scale properties of SiC-SiC composite constituents (matrix, fibers, interphase). The results will be coupled with meso-scale fiber and void structural information and be used as input to develop a comprehensive, finite element-based model based on constituent properties. The goal of this multi-scale model is to be used to predict anisotropic mechanical and thermal cladding behaviors. The model will be benchmarked against measurements of bulk properties and validated for radiation-damaged materials by utilizing irradiated SiC-SiC composites available from General Atomics. The characterization approach developed under this program will have particular application in the property prediction of reactor irradiated materials, as only small volumes need to be tested, minimizing associated hazards and costs. The micro-scale test methods developed here will be used along with meso-scale structural data to inform a finite element model of the full SiC-based cladding system. This model will capture fabrication and irradiation effects and importantly include for the first-time separate material data for each system component. The incorporation of these micro-scale effects will lead to a more accurate model of SiC-SiC composite behavior, enabling further advancements in the development and design of SiC-based materials for improved fuel cladding performance. The aim of this work is to develop advanced localized material characterization techniques to directly measure mechanical and thermal properties of the individual constituents of SiC-based claddings at the relevant micro-scale. SiC-SiC composites will be evaluated before and after irradiation and these results will be coupled with macro-scale properties and microstructural information in order to provide the input parameters for a comprehensive finite element model, which will be developed in this program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗