Search NASA⌕ Search

Engineering topics

Hou, Jiahui

Publications and source records attributed to Hou, Jiahui.

Direct regeneration of degraded LiFePO4 cathodes via a separator-enabled prelithiation strategy

A persistent challenge in lithium-ion batteries is the loss of active lithium due to the solid electrolyte interphase (SEI) formation and associated side reactions. While prelithiation employing lithium replenishment separator (LRS) has been proven effective in compensating for lithium loss, previous studies have largely been accompanied by gas evolution or solid residue formation during the prelithiation process. To surmount this challenge, we present a LRS based on 4-fluoro-1,2-dihydroxybenzene lithium salt (LiDF), capable of mitigating lithium loss while producing decomposition products that integrate directly into the electrolyte as functional additives which can assist with the stability of the SEI, free from gas or solid formation, thus establishing a sustainable and environmentally benign strategy for lithium compensation. Incorporation of the LRS enables the pristine LiFePO4||graphite (Gr) full cell to achieve 10.8% higher capacity than the cell with a polypropylene separator (PPS) after 200 cycles at 0.5C. Remarkably, the degraded LiFePO4 (D-LFP)||Gr full cell with the LRS exhibits a 135.8% capacity improvement over the PPS-based cell after 500 cycles. These findings establish the LRS as a powerful approach for both boosting high-performance lithium-ion batteries and recovering the capacity of degraded batteries.

Tao, Fujun↗

Recycled graphite enabled superior performance for lithium ion batteries

Recycling graphite attracts growing attention since cumulative amount of spent Li-ion batteries and the shortage of graphite supply chain. Although various recycling methods have been reported, the recycled graphite cannot reach the strict commercial standards of purity, scalability, efficiency, and capacity, preventing it from battery manufacturing. Herein, the important roles of defects and functional groups on the graphite surface are deeply studied, and a closed-loop graphite recycling process with the surface recovery and modification for the graphite from the end-of-life batteries is demonstrated. The recovered graphite delivers a purity of over 99.9 % and an average initial coulombic efficiency of 91.5 %. Compared with commercial graphite in industrial standard battery testing parameters, full cells with recovered graphite possess enhanced rate reversibility, doubled cycle life, over 10 % higher capacity along with half anode material cost. In conclusion, these impressive results not only underscore the transformative potential of surface reconstruction and modification in graphite recycling, but also present economic feasibility and sustainable pathway for significantly improving battery performance and addressing global resource challenges via integration with the hydrometallurgical recycling process.

25 ENERGY STORAGE↗

Acid Etching‐Driven Self‐Assembly of Mn‐Shell Inducing Rock‐Salt Phase for Enhanced Single‐Crystal Ni‐Rich Cathodes

With the wide adoption of Li‐ion batteries, Ni‐rich cathode is considered as one of the most promising candidates of cathodes due to its high energy density and low cost. However, stability decreased with increasing Ni content in the Ni‐rich cathode. To solve this bottleneck, many strategies, such as coating, doping, surface modification, and special morphologies, have been developed. Herein, we introduce a groundbreaking approach for enhancing Ni‐rich cathode through an innovative acid etching process that promotes Mn shell self‐assembly, inducing a rock‐salt phase on the surface. This method not only simplifies the Ni‐rich cathode modification process, but also significantly improves the structural stability and electrochemical performance of Ni‐rich cathode. Our findings demonstrate that developed single‐crystal Ni‐rich cathode shows 3–34 % better stability compared to both commercial modified Ni‐rich cathode and unmodified counterparts. The unique Mn shell effectively mitigates reversible phase shifts during cycling, contributing to a remarkable enhancement in cycling stability. Additionally, this novel fabrication technique paves the way for cost‐effective production of high‐performance cathode materials, offering substantial benefits for lithium‐ion battery technology. And this study proves the potential of this method in advancing the design and development of durable, high‐capacity cathode materials for next‐generation batteries.

Ni-rich cathode↗

Understanding the Effects of Bi Modification on the Properties of Ni-Rich Cathodes

With the skyrocketing market demands for energy storage, lithium ions batteries (LIB) with higher energy density are urgently needed. Cathodes play a critical role in determining the energy density of LIB, and the most popular one is Ni-rich cathode due to its high capacity. However, due to the fast structural degradation, Ni-rich cathode materials should be further modified to achieve higher stability. Herein, we introduce bismuth ions in LiNi 0.83 Co 0.11 Mn 0.06 O 2 cathodes by adding Bi 2 O 3 during sintering to optimize the specific capacity and cycle stability. By adding 0.1% mol Bi, the Li + diffusion and structural stability are effectively optimized, leading to improved electrochemical performances. Further, the modified sample delivers much higher specific capacity (222.9 mAhg -1 , 0.05 C) than unmodified sample (204 mAhg -1 , 0.05 C). Meanwhile, the specific capacity of optimized sample after 100 cycles at 0.33 C is 27.75 mAhg -1 higher than that of unmodified sample. Therefore, this work demonstrates that Bi modification can be regarded as a possible solution to optimizing the electrochemical performance of Ni-rich cathodes.

25 ENERGY STORAGE↗

Regulating Anionic Redox via Mg Substitution in Mn-Rich Layered Oxide Cathodes Enabling High Electrochemical Stability for Sodium-Ion Batteries

Here, with the limited resources and high cost of lithium-ion batteries (LIBs) and the ever-increasing market demands, sodium-ion batteries (SIBs) gain much interest due to their economical sustainability, and similar chemistry and manufacturing processes to LIBs. As cathodes play a vital role in determining the energy density of SIBs, Mn-based layered oxides are promising cathodes due to their low cost, environmental friendliness, and high theoretical capacity. However, the main challenge is structural instability upon cycling at high voltage. Herein, Mg is introduced into the P2-type Na 0.62 Ni 0.25 Mn 0.75 O 2 cathode to enhance electrochemical stability. By combining electrochemical testing and material characterizations, it is found that substituting 10 mol% Mg can effectively alleviate the P2–O2 phase transition, Jahn-Teller distortion, and irreversible oxygen redox. Moreover, structural integrity is greatly improved. These lead to enhanced electrochemical performances. With the optimized sample, a remarkable capacity retention of 92% in the half cell after 100 cycles and 95% in the full cell after 170 cycles can be achieved. Altogether, this work provides an alternative way to stabilize P2-type Mn-based layer oxide cathodes, which in turn, put forward the development of this material for the next-generation SIBs.

25 ENERGY STORAGE↗

Unraveling the nature of sulfide ions in hydrometallurgical recycling of NCM622 cathode material

The use of lithium-ion batteries (LIBs) has increased dramatically since its initial inception in the late 20th century. Such a surge in the LIB market and industry has resulted in a huge demand for mineral resources. Besides, the large scale of production will lead to massive amounts of waste batteries in the end. As such, recycling is seen as an end-of-pipe process to resolve sustainability and environmental concerns. The hydrometallurgical recycling is considered to be the most prominent method to recover cathode materials from spent LIBs owing to its high leaching efficiency and low energy costs. A series of procedures including pretreatment of the spent LIBs, acid leaching of the black mass, chemical co-precipitation of the hydroxide precursor, and sintering of the cathode active material need to be operated precisely. In this aspect, the impurities introduced during the process could pose a serious threat to the reaction stability as well as recycling consistency. Here, the impact of sulfide ions on recovered LiNi 0.6 Co 0.2 Mn 0.2 O 2 (NCM622) cathode material with the method of hydrometallurgy is first investigated in detail. This study shows that hydrometallurgical process is not obviously influenced by sulfide impurity. No signs of secondary phase or impurity inclusion are spotted in synthesized cathodes. Under 5 at % sulfide concentration conditions, the obtained NCM622 cathode exhibits a capacity of 159.4 mAh/g after 100 cycles at 1/3C, which is at the same level as virgin benchmark. The difference in rate performance between cathodes with and without additional sulfide is less than 2 % or even smaller. In short, the results indicate a neutral status of sulfide ions in hydrometallurgical recycling.

25 ENERGY STORAGE↗

Modeling assisted synthesis of Zr-doped Li 3-x In 1-x Zr x Cl 6 with ultrahigh ionic conductivity for lithium-ion batteries

All-solid-state lithium-ion batteries (ASSLBs) are an important milestone for the future of energy storage because of their capability of impressive energy density and outstanding safety. However, oxide and sulfide solid-state electrolytes (SSEs) suffer from either low ionic conductivity or poor chemical stability. In contrast, halide-based SSEs, are promising as candidate materials owing to high conductivity, good stability, and broad cathode compatibility. Though element doping of the SSEs is an effective and common approach to further improve their electrochemical properties, dopant exploration and optimization through solely experimental trials are both costly and time-consuming. For this aspect, computational simulations for dopant element and concentration screening are adopted in this research and zirconium is selected as a suitable dopant for Li 3 InCl 6 . Further, the synthesized Li 2.75 In 0.75 Zr 0.25 Cl 6 exhibited Li ionic conductivity of 5.82 x 10 -3 Scm -1 at room temperature, which is the highest among reported halide SSEs. The ASSLB formed with Li 2 CoO 2 -Li 2.75 In 0.75 Zr 0.25 Cl 6 -Li/In delivers a high initial capacity of 129.3 mAh∙g -1 . Conclusively, this work provides an effective approach which combines computational modeling and experimental verification for the development of halide SSEs with improved stability and conductivity. The successful design approach and compelling results provide further possibilities and capabilities in future SSE research.

25 ENERGY STORAGE↗

A green closed-loop process for selective recycling of lithium from spent lithium-ion batteries

As the economy started to recover from the COVID pandemic, the price of Li 2 CO 3 skyrocketed to its highest. This situation has aggravated concerns about the supply chain for lithium-ion batteries (LIBs). Recycling spent LIBs is a potential solution to alleviate the bottleneck of the supply chain and prevent environmental pollution, and has attracted lots of attention. However, lithium recycling is generally disregarded because of the complex recycling process and its low recycling efficiency. Here, in this work we developed a sustainable lithium recovery process, which can selectively leach and recover lithium with formic acid before recycling valuable metals. With the reported method, lithium can be 99.8% recovered from layered oxide cathode materials with 99.994% purity. In addition, this lithium recovery process is affordable, compared to the typical hydrometallurgical process, by saving 11.15% per kilogram of spent LIBs. Therefore, this research provided a new solution to eliminating the effects of lithium ions on valuable metal separation and the co-precipitation reaction and precluding the influence of other metal ions on lithium recovery. Finally, this simplified lithium recovery process provides new opportunities for sustainable recycling of LIBs and economical restoration of the lithium supply chain.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Upgrading the Performance and Stability of Lithium, Manganese-Rich Layered Oxide Cathodes with Combined-Formic Acid and Spinel Coating Treatment

We report improving sluggish rate performance and cycling stability of Li, Mn-rich cathode materials (LMR) is of great importance for practical implementation. Here, dual surface modification on LMR particles with formic acid washing and spinel coating improves the electrochemical performance. Dilute formic acid can remove the Li2CO3 surface impurities and selectively reduce Ni while significantly increasing specific surface area by ~32 %, unlocking more electrochemically active surfaces. Spinel coating enhances cycle stability by suppressing detrimental side reactions at electrode-electrolyte interfaces at high voltage. Post-annealing temperature was found to significantly affect the cathode performance. Higher temperature favors diffusion of transition metal (TM)/Li ions of the spinel coating from surface to the bulk, removing the coating by possible reconstruction into the layered structure and thus degrading the performance. The spinel coating also appears to increase Co 3+ segregation on the particle surface. Compared to the original material, the optimized sample demonstrates 47 % higher capacity retention at 3C and retains 89 % of initial capacity after 150 cycles at 0.5C. Besides, the specific energy density of 523 Wh kg -1 can be attained after 150 cycles at 0.5C. Moreover, the post-cycling analysis of modified sample verifies a better structural integrity with less particle cracking. Altogether, this study portrays an alternative strategy to overcome the shortcomings of LMR cathode materials.

25 ENERGY STORAGE↗

Building a spontaneously formed and self-healing protective layer with an F-rich electrochemically active organic molecule for ultra-stable Li metal batteries

Additives in the electrolyte act as engineers in Li metal batteries. Inspired by the superior cycle performance of organic materials in half cells, tetrafluoro-1,4-benzoquinone (TFBQ), the main structure of which has been widely applied as an organic cathode material, is utilized for the first time as an additive for Li metal protection. By chemical and electrochemical reactions between TFBQ and the Li metal surface, an F-rich interface layer is in situ formed on the Li metal surface during the charge and discharge process. From electrochemical tests and characterization, the powerful self-healing ability of the interface layer enabled by TFBQ is revealed, making an extremely stable Li metal anode. By using a lean electrolyte with 0.1 M TFBQ, the cycle life of Li|Li symmetric cells is increased at least 6 times compared to the control group. Moreover, impressive full cell performance was achieved. Ultra-stable Li–LFP cells showed a 0.026% average degradation for 600 cycles at 1C and Li–NMC622 cells showed a 36.8% higher capacity compared to the control group over 200 cycles at 0.5C, which are among the best results reported. Furthermore, this work efficiently and conveniently provides a new research direction to Li metal protection and Li metal batteries.

25 ENERGY STORAGE↗

A universal etching method for synthesizing high-performance single crystal cathode materials

LiNi x MnyCo 1-x-y O 2 (NMC) is considered the most appealing cathode material due to its high energy density and low cost. However, the stability and safety concerns, caused by the degradation of polycrystalline cathode materials during cycling, have restricted their practical applications. To overcome this shortcoming, converting polycrystalline cathode to high-performance single-crystal cathode materials becomes an appealing solution. In this work, a universal etching approach is firstly developed to synthesize single-crystal cathode materials. The rate performance of the obtained single-crystal NMC111 is 10–15% more than that of polycrystalline NMC111 whereas the capacity retention of single-crystal NMC111 is enhanced by ~12% after 300 cycles at 0.5C. The obtained single-crystal NMC622 exhibits a pronounced improvement in rate performance, especially at high rates (~28.6% better at 5C and ~129% better at 10C) and has a comparable cycle performance compared to polycrystalline NMC622. Altogether, the findings propose an alternative approach to generate single-crystal particles with high energy density and cycle stability for the next generation lithium-ion batteries.

25 ENERGY STORAGE↗