Search NASA⌕ Search

Engineering topics

Howell, S.

Publications and source records attributed to Howell, S..

Combined Retrievals of Boreal Forest Fire Aerosol Properties with a Polarimeter and Lidar

Absorbing aerosols play an important, but uncertain, role in the global climate. Much of this uncertainty is due to a lack of adequate aerosol measurements. While great strides have been made in observational capability in the previous years and decades, it has become increasingly apparent that this development must continue. Scanning polarimeters have been designed to help resolve this issue by making accurate, multi-spectral, multi-angle polarized observations. This work involves the use of the Research Scanning Polarimeter (RSP). The RSP was designed as the airborne prototype for the Aerosol Polarimetery Sensor (APS), which was due to be launched as part of the (ultimately failed) NASA Glory mission. Field observations with the RSP, however, have established that simultaneous retrievals of aerosol absorption and vertical distribution over bright land surfaces are quite uncertain. We test a merger of RSP and High Spectral Resolution Lidar (HSRL) data with observations of boreal forest fire smoke, collected during the Arctic Research of the Composition of the Troposphere from Aircraft and Satellites (ARCTAS). During ARCTAS, the RSP and HSRL instruments were mounted on the same aircraft, and validation data were provided by instruments on an aircraft flying a coordinated flight pattern. We found that the lidar data did indeed improve aerosol retrievals using an optimal estimation method, although not primarily because of the constraints imposed on the aerosol vertical distribution. The more useful piece of information from the HSRL was the total column aerosol optical depth, which was used to select the initial value (optimization starting point) of the aerosol number concentration. When ground based sun photometer network climatologies of number concentration were used as an initial value, we found that roughly half of the retrievals had unrealistic sizes and imaginary indices, even though the retrieved spectral optical depths agreed within uncertainties to independent observations. The convergence to an unrealistic local minimum by the optimal estimator is related to the relatively low sensitivity to particles smaller than 0.1 ( m) at large optical thicknesses. Thus, optimization algorithms used for operational aerosol retrievals of the fine mode size distribution, when the total optical depth is large, will require initial values generated from table look-ups that exclude unrealistic size/complex index mixtures. External constraints from lidar on initial values used in the optimal estimation methods will also be valuable in reducing the likelihood of obtaining spurious retrievals.

Knobelspiesse, K.↗

Kepler Ground-Based Photometry Proof-of-Concept

We report on our efforts to evaluate the feasibility of using the 4-Shooter CCD camera on the 48-inch reflector at the Whipple Observatory to carry out a multi-band photometric survey of the Kepler target region. We also include recommendations for future work. We were assigned 36 nights with the &hooter during 2003 for this feasibility study. Most of the time during the first two dozen nights was dedicated to the development of procedures, test exposures, and a reconnaissance across the Kepler field. The final 12 nights in September and October 2003 were used for "production" observing in the middle of the Kepler field using the full complement of seven filters (SDSS u, g, r, i, z, plus our special Gred and D51 intermediate-band filters). Nine of these 12 nights were clear and photometric, and production observations were obtained at 109 pointings, corresponding to 14.6 square degrees.

Brown, Timothy M.↗

Oscillating flow loss test results in Stirling engine heat exchangers

The results are presented for a test program designed to generate a database of oscillating flow loss information that is applicable to Stirling engine heat exchangers. The tests were performed on heater/cooler tubes of various lengths and entrance/exit configurations, on stacked and sintered screen regenerators of various wire diameters and on Brunswick and Metex random fiber regenerators. The test results were performed over a range of oscillating flow parameters consistent with Stirling engine heat exchanger experience. The tests were performed on the Sunpower oscillating flow loss rig which is based on a variable stroke and variable frequency linear drive motor. In general, the results are presented by comparing the measured oscillating flow losses to the calculated flow losses. The calculated losses are based on the cycle integration of steady flow friction factors and entrance/exit loss coefficients.

Koester, G.↗

Measurement of liquid water content in a melting snowpack using cold calorimeter techniques

Liquid water in a snowpack is a quantifiable parameter of hydrological significance. It is also important in the interpretation of snowpack remote sensing data using microwave techniques. One acceptable approach to measuring liquid water content of a snowpack (by weight) is the cold calorimeter. This technique is presented from theory through application. Silicon oil was used successfully as the freezing agent. Consistent results can be obtained even when using operators with a minimum of training. Data can be obtained approximately every 15 minutes by using two calorimeters and three operators. Accuracy within one to two percent can be achieved under reasonable field conditions.

Rango, A.↗

Snowpack ground truth: Radar test site, Steamboat Springs, Colorado, 8-16 April 1976

Ground-truth data taken at Steamboat Springs, Colorado is presented. Data taken during the period April 8, 1976 - April 16, 1976 included the following: (1) snow depths and densities at selected locations (using a Mount Rose snow tube); (2) snow pits for temperature, density, and liquid water determinations using the freezing calorimetry technique and vertical layer classification; (3) snow walls were also constructed of various cross sections and documented with respect to sizes and snow characteristics; (4) soil moisture at selected locations; and (5) appropriate air temperature and weather data.

Howell, S.↗