Search NASA⌕ Search

Engineering topics

Hsiao, Yu-Che

Publications and source records attributed to Hsiao, Yu-Che.

Investigating underlying mechanism in spectral narrowing phenomenon induced by microcavity in organic light emitting diodes

This paper reports our experimental studies on the underlying mechanism responsible for electroluminescence spectral narrowing phenomenon in the cavity-based organic lightemitting diodes. It is found that the microcavity generates an emerging phenomenon: a magneto-photoluminescence signal in Poly(9,9-dioctylfluorene-alt-benzothiadiazole) polymer under photoexcitation, which is completely absent when microcavity is not used. This provides an evidence that microcavity leads to the formation of spatially extended states, functioning as the intermediate states prior to the formation of Frenkel excitons in organic materials. This is confirmed by the magneto-electroluminescence solely observed from the cavity-based light-emitting diodes under electrical injection. Furthermore, the narrowed electroluminescence output shows a linear polarization, concurrently occurred with magnetoelectroluminescence. This indicates that the spatially extended sates become aligned towards forming coherent light-emitting excitons within the microcavity through optical resonance. Clearly, the spatially extended states present the necessary condition to realize electroluminescence spectral narrowing phenomenon towards lasing actions in cavity-based organic light-emitting diodes.

36 MATERIALS SCIENCE↗

Dynamic Coupling between Electrode Interface and Donor/Acceptor Interface via Charge Dissociation in Organic Solar Cells at Device-Operating Condition

Organic solar cells exhibit both electrode/photovoltaic (E/P) interface and donor/acceptor (D/A) interface in controlling the critical photovoltaic processes. Here, on the basis of the efficient PTB7:PC71BM solar cells, our studies on magneto-photocurrent with external bias provide the first evidence that the E/P interface and D/A interface are dynamically coupled at device-operating condition. Specifically, we observe a significant decrease (90%) in the critical bias required to completely dissociate the charge transfer (CT) states at D/A interface by changing the E/P interface with increased interface dipole field from ZnO to the polyelectrolyte (PFN). The experimental results demonstrate that strong dipole field at the E/P interface can effectively decrease the electron hole binding energy at D/A interface through the enhancement of built-in field applied on CT states. Clearly, our experimental studies provide new insight on the interfacial engineering through addressing the dynamic coupling between E/P interface and D/A interface in organic bulkheterojunction solar cells toward further improvement on photovoltaic efficiencies.

14 SOLAR ENERGY↗

Control of morphology and function of low band gap polymer–bis-fullerene mixed heterojunctions in organic photovoltaics with selective solvent vapor annealing

We reported how by replacing PCBM with a bis-adduct fullerene (i.e. ICBA) we significantly improve the open circuit voltage (VOC) and power conversion efficiency (PCE) in P3HT bulk heterojunctions. But, for the most promising low band-gap polymer (LBP) systems, replacing PCBM with ICBA results in very poor shortcircuit current (JSC) and PCE although the VOC is significantly improved. Therefore, in this work, we have completed small angle neutron scattering and neutron reflectometry experiments to study the impact of post-deposition solvent annealing (SA) with control of solvent quality on the morphology and performance of LBP bis-fullerene BHJ photovoltaics. Our results show that SA in a solvent that is selective for the LBP results in a depletion of bis-fullerene near the air surface, which limits device performance. SA in a solvent vapor which has similar solubility for polymer and bis-fullerene results in a higher degree of polymer ordering, bis-fullerene phase separation, and segregation of the bis-fullerene to the air surface, which facilitates charge transport and increases power conversion efficiency (PCE) by 100%. The highest degree of polymer ordering combined with significant bis-fullerene phase separation and segregation of bis-fullerene to the air surface is obtained by SA in a solvent vapor that is selective for the bis-fullerene. The resultant morphology increases PCE by 190%. These results indicate that solvent annealing with judicious solvent choice provides a unique tool to tune the morphology of LBP bisfullerene BHJ system, providing sufficient polymer ordering, formation of a bis-fullerene pure phase, and segregation of bis-fullerene to the air surface to optimize the morphology of the active layer. Furthermore, this process is broadly applicable to improving current disappointing LBP bis-fullerene systems to optimize their morphology and OPV performance post-deposition, including higher VOC and power conversion efficiency.

36 MATERIALS SCIENCE↗

Tuning the Morphology and Performance of Low Bandgap Polymer: Fullerene Heterojunctions via Solvent Annealing in Selective Solvents

Low bandgap polymer (LBG):fullerene mixtures are some of the most promising organic photovoltaic active layers. Unfortunately, there are no post-deposition treatments available to rationally improve the morphology and performance of as-cast LBG:fullerene OPV active layers, where thermal annealing usually fails. Therefore, there is a glaring need to develop postdeposition methods to guide the morphology of LBG:fullerene bulk heterojunctions towards targeted structures and performance. In this paper, the structural evolution of PCPDTBT:PCBM mixtures with solvent annealing (SA) is examined, focusing on the effect of solvent quality of the fullerene and polymer in the annealing vapor on morphological evolution and device performance. The results indicate that exposure of this active layer to the solvent vapor controls the ordering of PCPDTBT and PCBM phase separation very effectively, presumably by inducing component mobility as the solvent plasticizes the mixture. These results also unexpectedly indicate that solvent annealing in a selective solvent provides a method to invert the morphology of the LBG:fullerene mixture from a polymer aggregate dispersed in a polymer:fullerene matrix to fullerene aggregates dispersed in a polymer:fullerene matrix. The judicious choice of solvent vapor, therefore, provides a unique method to exquisitely control and optimize the morphology of LBG conjugated polymer/fullerene mixtures.

Chen, Huipeng↗

The Impact of Fullerene Structure on Its Miscibility with P3HT and Its Correlation of Performance in Organic Photovoltaics

Neutron reflectivity experiments are utilized to obtain the miscibility limit of four different fullerenes, bis-PCBM, ICBA, thio-PCBM, and PC70BM, in poly(3-hexylthiophene) (P3HT). The intermixing of P3HT and fullerene bilayers is monitored by neutron reflectivity before and after thermal annealing, providing quantification of the miscibility and interdiffusion of the fullerene within P3HT. These results indicate that the miscibility limit of these fullerenes in P3HT ranges from 11% to 26%, where the bis-adduct fullerenes exhibit lower miscibility in P3HT, which is also verified by small angle neutron scatting (SANS). The in-plane morphology of the P3HT:fullerene mixtures was also examined by SANS, which shows a decrease in domain size and an increase in the specific interfacial area between the fullerene and the polymer with the bis-fullerenes. Correlation of miscibility and morphology to device performance indicates that polymer/ fullerene miscibility is crucial to rationally optimize the design of fullerenes for use in organic photovoltaics. Bis-PCBM has a higher open circuit voltage (Voc) than PC60BM with P3HT; however, device performance of bis-PCBM based devices is lower than that of PC60BM based devices. This decrease in performance is attributed to the lower miscibility of bis-PCBM in P3HT, which decreases the probability of exciton dissociation and enhances the recombination of free charge carriers in the miscible region. Moreover, the minimum distance between fullerenes in the miscible region to facilitate intermolecular transport is identified as 11 .

Chen, Huipeng↗