Search NASA⌕ Search

Engineering topics

Hu, Boxun

Publications and source records attributed to Hu, Boxun.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Prospects of hydrogen cogeneration and carbon dioxide utilization in electrochemical refineries for ethylene production via oxidative coupling of methane: A techno-economic assessment

Ethylene is recognized as one of the most significant chemicals globally. The projected ethylene production for 2023 stands at 227.6 million tonnes, with expectations of continued demand growth. The primary use of ethylene, accounting for over 76%, lies in the production of plastics such as polyethylene, polyvinyl chloride, and polystyrene. Despite the enduring carbon retention potential of plastics themselves, traditional ethylene feedstock production from fossil resources contributes substantially to greenhouse gas emissions, ranging from 0.29 to 2.29 kg CO2 /kg Ethylene depending on various factors like feedstock and process design. Various decarbonization strategies, including the utilization of hydrogen as a primary heat source, have been proposed to reduce the carbon footprint of ethylene production, but their efficacy remains limited, offering at best a 0–30% reduction in on-site CO 2 emissions.

09 BIOMASS FUELS↗
DOE OSTI2024

Dynamic operation of metal-supported solid oxide electrolysis cells

Symmetric-structure metal-supported solid oxide fuel cells and electrolysis cells (MS-SOFCs, MS-SOECs) offer several advantages over conventional solid oxide cells, including the use of inexpensive materials, high mechanical strength, and rapid ramp-up ability. Aggressive operation of MS-SOCs in fuel cell mode is well-established, including extremely fast start-up, redox tolerance, and imbalanced pressure. Here, we extend dynamic operation to MS-SOCs in SOEC mode with high steam content for both small button cells and a large rectangular cell, including: steam cycling, thermal cycling, redox cycling and power cycling. Steam cycling entailed switching between 3:97 and 50:50 steam:hydrogen ratio. For thermal cycling, the temperature was rapidly varied between 150°C and 700°C for 50 cycles. Redox cycling involved switching the steam side gas between 50 % humidified H 2 and 50 % humidified N 2 for 5 cycles. Power cycling was performed by operating the cell under variable current density, resulting in cell voltage between 1.3V and 2.8V. Degradation rates for each testing strategy were compared to a baseline cell, and found to be similar. In conclusion, the excellent tolerance to dynamic operation increases confidence that MS-SOECs will be compatible with dynamic or intermittent renewable resources.

08 HYDROGEN↗
DOE OSTI2023

Ethanol-fueled metal supported solid oxide fuel cells with a high entropy alloy internal reforming catalyst

High-performance metal supported solid oxide fuel cells (MS-SOFC) with an integrated high entropy alloy (HEA) internal reforming catalyst (IRC) are demonstrated for transportation applications using ethanol and methanol as fuels. Addition of the HEA IRC dramatically improves cell performance and stability when using ethanol/water blend fuel. Absence of carbon deposition predicted by thermodynamic calculations is confirmed by Raman spectroscopy analysis of posttest anodes. Optimal catalyst processing (deposition technique, loading, firing temperature) and cell operation conditions (flow rates, temperature, fuel compositions) are explored. Infiltrated HEA reforming catalyst provides a highly porous structure and low catalyst loading (6 mg cm –2 ). The designed structure and catalysts achieve small mass transport resistances in the fuel electrode (26.2 s m –1 ) and oxygen electrode (41.6 s m –1 ). The best ethanol concentration (60:40 v% ethanol: water) provides 0.83 W cm –1 at 700 °C, without carbon deposition. The ethanol-fueled MS-SOFC is operated for 500 h, including five thermal cycles. As a result, cell evolution is similar to that reported previously for hydrogen fuel; nickel aggregation and chromia deposition were the major observed changes, and carbon formation can be avoided even after long-term operation.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Electrochemical conversion of methane to ethylene, olefins, and paraffins using metal-supported solid oxide cells

Electrochemical oxidative coupling of methane (E-OCM) with Sr 2 Fe 1·5 Mo 0·5 O 6–δ (SFM) catalyst is demonstrated with metal-supported solid oxide cells (MS-SOC). SFM anode and Pr 6 O 11 cathode catalysts are loaded into a porous symmetric-architecture cell by infiltration and firing. The most effective chelating agent (citric acid/ethyl glycol) and optimal firing/reducing temperatures (850 °C/750 °C) for the SFM catalyst precursor solution are selected and confirmed by cell testing. Operating temperature, cell voltage, and oxygen concentration at the cathode greatly affect the methane conversion rate and product selectivity by controlling the oxygen ion flow. CH 4 conversion of 85.8% is obtained, with C 2 H 4 , C 2 H 6 , and H 2 concentrations of 10.5%, 12.3%, and 25.6% at 800 °C, respectively, in the product exhaust gas. Reasonable stability of the current density and methane conversion is demonstrated during 200 h operation. Furthermore, this research demonstrates technical progress in catalyst and device development for the E-OCM reaction to synthesize valuable chemicals.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Direct Utilization of Pure and Denatured Ethanol in Metal Supported Solid Oxide Fuel Cells

Metal supported solid oxide fuel cells (MS-SOFC) are integrated with internal reforming catalyst for direct utilization of ethanol to generate electricity. MS-SOFCs are operated up to 500 h at 700°C, with water-ethanol blend fuel using high-purity ethanol and denatured ethanol. Performance and durability with denatured ethanol varies dramatically with the composition of the denaturant. Cells operated with three denatured ethanol fuels containing small amount of methanol, isopropanol, and denatonium benzoate demonstrate similar and relative stable performance after stabilization, suggesting that these fuels are fit for MS-SOFC operation. No or minimum carbon deposits are observed on the high entropy alloy-based reforming catalyst layer. Denatured ethanol containing gasoline and toluene leads to fast degradation. Here, MS-SOFCs are promising for direct utilization of denatured ethanol, offering a path to rapid-start, carbon-neutral operation with widely-available fuels.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2023

Optimization of metal-supported solid oxide electrolysis cells with infiltrated catalysts

We report metal-supported solid oxide electrolysis cells (MS-SOECs) are being developed for steam-to-hydrogen electrolysis, especially for utilization of dynamic or intermittent electrical power from renewable sources. Various aspects of the electrocatalyst processing and composition, and metal support structure were explored. Catalyst materials, infiltration temperature and infiltration cycles were optimized for high performance and durability. Numerous catalyst materials were screened for both oxygen and steam electrodes. The oxygen catalyst had moderate impact on both initial cell performance and durability. Reducing Ni content in the steam electrode had little effect on durability, but reduced initial performance. Ex-situ XRD analysis and cell assessment of catalyst infiltration temperature revealed that the optimal range is 750–850 °C. The best cell performance and durability was achieved with LSCF-SDC oxygen electrocatalyst and SDC-Ni (60:40 vol%) steam electrocatalyst infiltrated 11 times at 800 °C and operated at 700 °C. At low steam content, a significant mass transport limitation on the steam side results in limiting current behavior. Thinner and more porous metal supports were implemented, and found to improve steam mass transport at low steam content, relevant for SOECs operating under high H 2 recycle rate or high steam utilization.

08 HYDROGEN↗
DOE OSTI2022

Optimization of metal-supported solid oxide fuel cells with a focus on mass transport

Performance of symmetric-architecture metal-supported solid oxide fuel cells was improved significantly by optimizing the catalyst infiltration process and metal support structure. Optimization of component structure and processing parameters was performed during tape-casting and fabrication of button cells. Mass transport of oxygen in the metal support was identified as a major limitation. To overcome this limitation, pore former loading and thickness of the metal support (130–250 μm) were optimized. The catalyst infiltration process was also improved by studying the impact of firing temperature (400 °C–900 °C) and infiltration cycle numbers (1–15). The maximum power density of the optimized cell was 0.9 W cm –2 at 700°C using hydrogen as a fuel, a three-fold increase over the baseline cell performance. The degradation rate of optimized cells at 550 °C, 600 °C, and 700 °C was 2%, 4.5%, and 5.5% per 100 h, respectively. Here, the phenomena of mass transport, catalyst coarsening, and chromium poisoning on the catalyst were analyzed by electrochemical impedance spectroscopy and scanning electron microscopy.

13 HYDRO ENERGY↗
DOE OSTI2022

Direct utilization of gaseous fuels in metal supported solid oxide fuel cells

Direct utilization and internal reforming of gaseous fuels is investigated on symmetric-architecture metal supported solid oxide fuel cells (MS-SOFCs) with thin ceramic electrolyte and scaffold backbone layers, and low cost ferritic stainless steel supports on both sides. Infiltrated Pr-oxide and Ni/samarium-doped ceria catalysts are added to the cathode and anode electrodes, respectively. Initial performance and durability is evaluated for MS-SOFCs operating with natural gas, propane, ammonia, and dimethyl ether at 700 °C. Cells for natural gas and propane utilize a novel high entropy alloy (HEA) catalyst for internal reforming with performance and degradation rates similar to H 2 (0.5W cm -2 and ~12%/100 h). In conclusion, initial testing with sulfur shows reversible degradation for levels found in natural gas and irreversible degradation for higher levels found in commercial propane. Overall, MS-SOFCs show successful fuel flexibility.

08 HYDROGEN↗
DOE OSTI2022

Metal-supported solid oxide fuel cells operating with reformed natural gas and sulfur

The performance, long-term durability, and thermal cycling tolerance of metal supported solid oxide fuel cells (MS-SOFCs) operating with natural gas reformate fuels is assessed. Symmetric MS-SOFCs with composite SDC-Ni anode catalysts and PrO x cathode catalysts are operated with simulated natural gas steam-reformate and partial-oxidation-reformate fuels with 1 ppm and 5 ppm of sulfur. Cells are operated for 1000 h with initial degradation rates similar to humidified H 2 , and initial performance differences attributed to the lower H 2 concentration in reformate fuels. Additionally, cells tolerate many aggressive thermal cycles with sulfur present, with minimal impact on performance. Post mortem analysis suggests that Ni particle coarsening and Cr deposition are sources of degradation, while carbon and sulfur deposition are not observed. Overall, MS-SOFCs operate successfully with reformed natural gas.

08 HYDROGEN↗
DOE OSTI2021

Scaleup and manufacturability of symmetric-structured metal-supported solid oxide fuel cells

Metal-supported solid oxide fuel cells with symmetric architecture, having metal supports on both sides of the cell, are scaled up from button cell size to large 50 cm 2 active area cell size. The cells remain flat after sintering assisted by the symmetric structure. Equivalent performance is achieved for button cells and large cells, and thermal cycling and redox cycling tolerance are demonstrated for the large cells. The catalyst infiltration process is improved to enable high-throughput manufacturing. The cumbersome lab-scale molten nitrate infiltration process is replaced with a room-temperature process in which a shelf-stable aqueous solution of nitrate salts is applied to the cell by spraying, painting, or other scalable techniques. Here, a fast-ramp thermal conversion of the nitrate salts to the final oxide catalyst composition is implemented, allowing many infiltration cycles to be accomplished in a single work shift. Increasing the number of infiltration cycles from 5 to 10 led to an increase in peak power density from approximately 0.3 to 0.52 W cm -2 .

25 ENERGY STORAGE↗
DOE OSTI2020

Advanced Anode for Internal Reforming and Thermal Management in Solid Oxide Fuel Cells

Solid oxide fuel cell (SOFC) is an efficient and clean electrical power generation system compared to conventional combustion based technologies with energy efficiency reaching as high as 85-90% in co-generation mode (electricity and heat). Other advantages of SOFCs are hybridization, modularity of construction, small CO 2 foot print per kWh of generated electricity and fuel flexibility. Hydrocarbons present in the gaseous fuel is utilized in SOFCs by internal or external reforming. There are two different internal reforming concepts: Direct Internal Reforming (DIR) and Indirect Internal Reforming (IIR). For DIR operation, the endothermic reforming reaction and the exothermic reaction from the oxidation reaction are operated together in the single unit eliminating the requirement for a separate fuel reformer. This configuration also simplifies the overall system design, making SOFC more attractive and efficient means of producing electrical power. The main advantage of the DIR type of operation is that the H 2 or CO consumption by the electrochemical reaction could directly promote the conversion of methane at the anode side of the fuel cell resulting in high conversion and high efficiency. The DIR operation, however, requires an anode material that has desired dual catalytic (hetero and electro) properties for reforming reaction and electrochemical reactions. The anode materials also need to remain resistant to carbon formation at the operating temperature and atmosphere with stable cell performance. Another requirement is to match the reforming reactions and electrochemical reactions to avoid local cooling or overheating, which can result in mechanical failure due to thermally induced stresses. Direct internal reforming (DIR) of hydrocarbon fuels simplifies the overall SOFC system design making it more attractive and efficient for producing electrical power. Low cost alloy anodes for distributed internal reforming of methane and other hydrocarbon fuels offer increased fuel-flexibility, reliability, and long term performance stability of solid oxide fuel cells (SOFC). The research program examined modification of the chemical compositions and microstructure of high entropy alloy (HEA) anode materials using thermochemical calculations and process simulation and modeling to achieve distributed reforming over the entire anode to eliminate hot zones. Cell fabrication and testing of the HEA anodes using button cell configuration has been performed to demonstrate the advantages of new anode over traditional Ni-YSZ anodes for distributed reforming and carbon free operation. Technical accomplishments include identification and synthesis of HEA carbon-resistant anode, demonstration of reduction in reforming rate confirmed by GC and modelling data validating effectiveness for thermal management in cell/stacks, electrochemical testing of HEA anode in single cell (HEA-GDC||YSZ||LSM-YSZ) and Characterization of pretest and posttest anode materials by TEM and SEM-EDS confirming carbon-free operation.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2020

Self-sustainable protonic ceramic electrochemical cells using a triple conducting electrode for hydrogen and power production

The protonic ceramic electrochemical cell (PCEC) is an emerging and attractive technology that converts energy between power and hydrogen using solid oxide proton conductors at intermediate temperatures. To achieve efficient electrochemical hydrogen and power production with stable operation, highly robust and durable electrodes are urgently desired to facilitate water oxidation and oxygen reduction reactions, which are the critical steps for both electrolysis and fuel cell operation, especially at reduced temperatures. In this study, a triple conducting oxide of PrNi 0.5 Co 0.5 O 3-δ perovskite is developed as an oxygen electrode, presenting superior electrochemical performance at 400-600°C. More importantly, the self-sustainable and reversible operation is successfully demonstrated by converting the generated hydrogen in electrolysis mode to electricity without any hydrogen addition. The excellent electrocatalytic activity is attributed to the considerable proton conduction, as confirmed by hydrogen permeation experiment, remarkable hydration behavior and computations.

08 HYDROGEN↗
DOE OSTI2020

Materials and Approaches for Mitigation of SOFC Cathode Degradation in SOFC Power Systems

Perovskites such as doped lanthanum manganite and cobaltite have been used successfully as a cathode material in SOFC power systems operating between 700-1000°C. The electrodes, however, remain prone to degradation in presence of Cr containing gas atmosphere under systems operating conditions. Cathode in SOFCs is considered as one of the largest contributors of electrochemical performance degradations, leading to significant increase in ohmic and non-ohmic losses as well as interfacial compound formation. These degradations are mostly irreversible due to permanent changes to chemical and morphological alterations in the electrodes, resulting in the blockage of triple phase boundary (TPB) sites and decrease in oxygen reduction reactions (ORR). Fundamental mechanistic understanding has been developed to elucidate the reaction pathways of electrode poisoning in electronically conducting electrodes (LSM) as well as mixed ionic and electronically conducting electrodes (LSCF). The overall goal of this program has been identification and development of cost effective solutions to mitigate electrode degradations under “real world” systems operating conditions. The overall technological innovations and impact from this work are: The research provides an understanding of the degradation mechanism and cost-effective approaches for implementation in SOFC systems; Develop mitigation processes utilizing low cost getters using conventional synthesis and fabrication route; Develop tailored high surface area powders and coatings for high Cr capture capacity under systems operating conditions; >Developed computational models to understand mechanistic behavior; Experimentally measure rate of Cr evaporation from chromia and alumina forming alloys under SOFC operating conditions; Developed conditions to minimize Cr evaporation from balance-of-plant alloys; This innovation will support the development of getter platform to capture both intrinsic and extrinsic impurities present in air; and, Applications under wide operating temperature range (500-900°C) as well for wide high-temperature electrochemical systems (SOFC, SOEC, and OTM). The work has been successfully developed, validated experimentally and implemented. Successful technology transfer of this knowledge with industrial partners has been accomplished and the getters have been independently tested and validated under their systems operating conditions. The innovation will also find application in related high temperature electrochemical systems such as OTM and SOEC for the prevention of Cr assisted performance degradation. The proposed approach for Cr capture can also be applied to oxy-combustion and other advanced combustion techniques for the reduction of Cr vapor in the exhaust gas stream. This fundamental knowledge gained also has led to the path forward for developing advanced getters for capturing more than one contaminant in air.

01 COAL, LIGNITE, AND PEAT↗