Search NASA⌕ Search

Engineering topics

Hu, Jiangtao

Publications and source records attributed to Hu, Jiangtao.

18 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Simultaneous Single Crystal Growth and Segregation of Ni-Rich Cathode Enabled by Nanoscale Phase Separation for Advanced Lithium-Ion Batteries

Here, a novel nanoscale phase separation process has been discovered to promote the growth and segregation of single-crystal LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811). This process occurs directly during high-temperature calcination without significant agglomeration. The key lies in converting transition metal hydroxide (TM(OH) 2 ) precursors with well-controlled morphology into transition metal oxide (TMO) intermediates before reacting them with lithium salt. The nanoscale redistribution of Ni in TMO, resulting from the concurrent formation of spinel and rock salt phases, helps to deagglomerate the clusters of later-formed NMC811 crystals. The as-prepared single-crystal NMC811 is further validated in a 2Ah pouch cell, demonstrating 1,000 stable cycles. The fundamentally new reaction mechanism of single-crystal growth and segregation provides a new direction for large-scale synthesis of a broad range of single crystals for advanced energy storage.

25 ENERGY STORAGE↗
DOE OSTI2022

Direct Imaging of the Structural and Morphological Evolution of Epitaxial LiCoO 2 Films during Charge and Overcharge

The capacity decay of layered cathodes in high-voltage applications underscores the need to utilize accurate and precise techniques to understand the underlying mechanisms. Here, we use well-defined epitaxial LiCoO 2 (LCO) films on SrRuO 3 /SrTiO 3 (SRO/STO) with controlled orientations and defect structures along with in situ electrochemical atomic force microscopy to probe the structural and morphological evolutions during the charge and overcharge processes. We quantitatively show the morphological changes in both the reversible delithiation regime and the irreversible over-delithiation regime and correlate the overall electrochemical behaviors to atomic scale defect evolutions in the films. Further, we also observe a significantly lower charging capacity for LCO/SRO/STO(111) compared to that of LCO/SRO/STO(001) films of the same thickness, which is ascribed to different types of atomic scale defects formed during the film growth process. Our high- resolution scanning transmission electron microscopy (STEM) and electron energy loss spectroscopy (EELS) studies reveal that the antiphase boundaries in LCO/SRO/STO(111) act as viable channels for Li migration but are more susceptible to irreversible phase transitions, which then block subsequent Li diffusion. The failure mechanisms developed here may provide insight into the design of future cathode materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Additive engineering for robust interphases to stabilize high-Ni layered structures at ultra-high voltage of 4.8 V

Nickel-rich layered cathode materials promise high energy density for next-generation batteries when coupled with lithium metal anodes. However, the practical capacities accessible are far less than the theoretical values due to their structural instability during cycling, especially when charged at high voltages. Here we demonstrate that stable cycling with an ultra-high cut-off voltage of 4.8 V can be realized by using an appropriate amount of lithium difluorophosphate in a common commercial electrolyte. The Li||LiNi 0.76 Mn 0.14 Co 0.10 O 2 cell retains 97% of the initial capacity (235 mAh g -1 ) after 200 cycles. The cycling stability is ascribed to the robust interphase on the cathode. It is formed by lithium difluorophosphate decomposition, which is facilitated by the catalytic effect of transition metals. The decomposition products (Li 3 PO 4 and LiF) form a protective interphase. This suppresses transition metal dissolution and cathode surface reconstruction. It also facilitates uniform Li distribution within the cathode, effectively mitigating the strain and crack formation.

25 ENERGY STORAGE↗
DOE OSTI2022

Facile Dual-Protection Layer and Advanced Electrolyte Enhancing Performances of Cobalt-free/Nickel-rich Cathodes in Lithium-Ion Batteries

Despite cobalt (Co)-free/nickel (Ni)-rich layered oxides being considered as one of the promising cathode materials due to their high specific capacity, their highly reactive surface is one of the shortcomings that still hinder their practical usages in high-energy-density batteries. Herein, a polyimide/polyvinylpyrrolidone (PI/PVP, denoted as PP) coating layer is demonstrated as dual-protection for LiNi 0.96 Mg 0.02 Ti 0.02 O 2 (NMT) cathode material to suppress surface contamination against moisty air and to prevent unwanted side reactions between cathode and electrolyte during electrochemical cycling. The optimal PP-coated NMT (PP@NMT) preserves a clean surface without generation of lithium (Li) residues, structural degradation, and gas evolution after exposure to air with ~30% humidity for 2 weeks. Contrarily, the exposed bare NMT shows severe contamination, structural shrinkage due to Li loss, and increased gas release during charging. In addition, the exposed PP@NMT significantly enhances the electrochemical performance of graphite (Gr)||NMT cells by decreasing byproducts and maintaining structural stability. Moreover, the exposed PP@NMT achieves a high capacity retention of 86.7% after 500 cycles in Gr||NMT cells using an advanced localized high-concentration electrolyte. Furthermore, this work demonstrates a promising facile approach to the protection of Co-free/Ni-rich layered cathodes for their practical applications even after exposure to moisty air.

25 ENERGY STORAGE↗
DOE OSTI2022

Locking oxygen in lattice: A quantifiable comparison of gas generation in polycrystalline and single crystal Ni-rich cathodes

High-energy Ni-rich NMC (LiNi x Mn y Co 1-x-y O 2 , x ≥ 0.6) is a very promising cathode material in Li-ion batteries but the gas generation during cycling is a significant safety concern and becomes the major roadblock of the large-scale commercialization of Ni-rich NMC cathode materials. Micron-sized single crystal Ni-rich NMC has a potential to address the common issues that polycrystals have. However, it is unknown if gassing issue will be mitigated or even eliminated by using single crystals, not mentioning a quantifiable understanding of gas generation from single crystals and polycrystals. This work takes LiNi 0.76 Mn 0.14 Co 0.1 O 2 (NMC76) as a model material to study the mechanism of gas generation from single crystal and polycrystalline NMC by using both coin cells and pouch cells, which provides different conclusions on the generated gases, highlighting the importance of using relevant testing conditions for fundamental diagnostic study on battery materials. Further, the information from single crystal NMC also provides critical insights from material perspective to enhance the safety attributes of Ni-rich NMC cathodes.

25 ENERGY STORAGE↗
DOE OSTI2021

Stable Solid Electrolyte Interphase Layer Formed by Electrochemical Pretreatment of Gel Polymer Coating on Li Metal Anode for Lithium–Oxygen Batteries

Lithium (Li)-oxygen (O2) batteries (LOBs) exhibit the highest theoretical specific energy density among candidates of the next-generation energy storage systems, but the instability of Li metal anode (LMA), air electrode, and electrolyte largely limit the practical energy density of these batteries. Herein, we report an effective method to protect LMA against side reactions between LMA and crossover contaminants such as highly reactive oxygen moieties. A solid electrolyte interphase (SEI) layer rich in inorganic components was formed on a LMA coated with polyethylene oxide thin-film through an in-situ electrochemical pre-charging step under oxygen atmosphere. This uniformly distributed stiff SEI layer interacted with flexible polymer matrix and formed a submicron-sized gel-like polymer layer. This polymer supported SEI layer leads to much longer cycle life (130 vs. 65 cycles) as compared to those of pristine cell under the same testing conditions (1.0 mAh cm-2 at 0.2 mA cm-2 in the voltage range of 2 to 5 V without any catalysts). It is also very effective during low voltage (2 to 4.5 V) cycling with a redox mediator (0.1 and 0.15M (2,2,6,6-tetramethylpiperidin-1-yl) oxidanyl). Therefore, this approach can be used to stabilize LMA/electrolytes interphase and improve the cycle life of rechargeable LOBs.

lithium-oxygen batteries, lithium metal anodes, ar↗
DOE OSTI2021

Toward the Practical Use of Cobalt-Free Lithium-Ion Batteries by an Advanced Ether-Based Electrolyte

The criticality of cobalt (Co) has been motivating the quest for Co-free positive electrode materials for building lithium (Li)-ion batteries. However, the Co-free positive electrode materials usually suffer from relatively fast capacity decay when coupled with conventional LiPF 6 -organocarbonates electrolytes. To address this issue, a 1,2-dimethoxyethane (DME) based localized high concentration electrolyte (LHCE) was developed and evaluated in a Co-free Li-ion cell chemistry (Graphite||LiNi 0.96 Mg 0.02 Ti 0.02 O 2 ). Extraordinary capacity retentions were achieved with the LHCE in coin cells (95.3%), single layer pouch cells (79.4%) and high capacity loading double layer pouch cells (70.9 %) after being operated within the voltage range of 2.5-4.4 V for 500 charge/discharge cycles. The capacity retentions of counterpart cells using LiPF6 based conventional electrolyte only reached 61.1%, 57.2% and 59.8%, respectively. Mechanistic studies reveal that the superior electrode/electrolyte interphases formed by the LHCE and the intrinsic chemical stability of the LHCE account for the excellent electrochemical performance in the Co-free Li-ion cells.

25 ENERGY STORAGE↗
DOE OSTI2021

A Polymer-in-Salt Electrolyte with Enhanced Oxidative Stability for Lithium Metal Polymer Batteries

Lithium (Li) metal polymer batteries (LMPBs) are a promising candidate of solid-state batteries with high safety. However, rare progress has been demonstrated so far in high voltage stability of polyethylene oxide (PEO) based polymer electrolytes for LMPBs. Herein, we revived the polymer-in-salt electrolyte (PISE) strategy based on the PEO-LiFSI system with EO/Li = 8 through a dry process to avoid the contamination of the residual solvent. The obtained PISEs exhibit quite different morphologies and coordination structures which greatly enhance the oxidative stability of polymer electrolytes. P(EO)1LiFSI has a low melting temperature, a high ionic conductivity at 60 ?C and an oxidative stability of ~4.5 V vs. Li/Li+ (overcoming the inherent low oxidative stability of PEO). With an effective interphase rich in inorganic species, in combination with good stability of the hybrid polymer electrolyte towards Li metal, the cycling stability of Li||LiNi1/3Co1/3Mn1/3O2 is greatly improved. The LMPB can retain 74.4% of capacity after 186 cycles at 60 ?C under the charge cutoff voltage of 4.3 V. The findings point out a promising strategy to develop high-voltage stable polymer electrolytes for high energy-density and safe LMPBs.

Polymer-in-salt electrolyte, lithium metal battery↗
DOE OSTI2021

Achieving Highly Reproducible Results in Graphite-based Li-ion Full Coin Cells

Electrode materials, cathodes or anodes, are mostly evaluated in half coin cells where lithium (Li) metal is used. However, due to the instability nature of Li metal, the cycling performances of the half cells is more likely reflecting Li anode stability instead of the coupled electrodes, questioning the conclusions. Full coin cells utilizing graphite as the anode effectively assesses materials. But the key factors of preparing full coin cells with reproducible performances have rarely been discussed and overlooked leading to many inconsistent results. This work discusses the scientific gap between cell preparation and observed electrochemical performances to unveil the key parameters for achieving consistent and reliable results in full coin cells, critical for effective evaluation of any new materials tested under relevant conditions. The knowledge from this work is broadly applicable in other full cells systems such as Si-based full cells or Na-ion batteries.

Hu, Jiangtao↗
DOE OSTI2021

Origin, nature, and the dynamic behavior of nanoscale vacancy clusters in Ni-rich layered oxide cathodes

Oxygen and transition metal (TM) vacancies in transition metal oxides (TMOs) play an important role in materials functionalities. For TMO cathodes of Li-ion batteries, vacancies can be introduced, either deliberately or inevitably, during materials synthesis or upon electrochemical cycling. Effects of vacancies on the electrochemical properties of cathodes critically depend on the dynamic characteristics of vacancies during the battery cycling. However, a fundamental understanding of such characteristics in the layer structured cathode remains elusive. Here, using scanning transmission electron microscopy (STEM), we reveal a cycling-induced aggregation behavior of oxygen and TM vacancies in a Ni-rich layer structured cathode of secondary particles. We discover that during the initial charging, vacancies aggregate to form visible vacancy-rich nanoregions (vacancy clusters) firstly at the outer layer of the secondary particle, and then the vacancy-cluster populated region extends to the inner part of particle upon fully charged. The spatial distinction of preferential nucleation of vacancy clusters at the outer layer indicates that the vacancy migration and clustering is associated with Li migration flux, which is larger at the outer layer, as all the Li from the inner part has to go through the outer layer. With extended cycling (> 50), these vacancy clusters become immobilized. We further reveal that the generation of these vacancy clusters is correlated to the material-synthesis conditions. Our findings solve a long-standing puzzle on the origin, nature, and behavior of the commonly visible vacancy clusters in the NMC cathode, providing insights on correlation between properties and dynamic behaviors of atomic-scale defects in layered oxide cathodes.

Li-ion batteries, layered oxide cathodes, NMC, cat↗
DOE OSTI2021

Electrolyte Regulating toward Stabilization of Cobalt-Free Ultrahigh-Nickel Layered Oxide Cathode in Lithium-Ion Batteries

Cobalt (Co)-free ultrahigh-nickel (Ni) layered oxides exhibit a double-edged competitive advantages in reducing the cathode cost and boosting the energy density, promising the sustainable development of batteries for electric vehicles. However, the increased Ni content, resultantly more highly oxidative Ni 4+ , potentially induces severe capacity fading due to the aggravated side reactions, limiting the practical applications. Here, we evaluate the compatibility of two localized high-concentration electrolytes (LHCEs) with LiNi 0.96 Mg 0.02 Ti 0.02 O 2 (NMT) cathode under a high charging voltage of 4.4 V in lithium ion batteries. The LHCE with EC additive enables the formation of stable interfacial layers on both NMT cathode and graphite anode, thus realizing a capacity retention of 97.2% over 200 cycles at 25 °C and high reversible capacities of ~180.2 and ~185.8 mAh g -1 , respectively, at 5C charge rate and 5C discharge rate. This study offers a promising approach to enable Co-free ultrahigh-Ni layered oxides for practical applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Effects of fluorinated solvents on electrolyte solvation structures and electrode/electrolyte interphases for lithium metal batteries

Electrolyte is very critical to the performance of the high-voltage lithium (Li) metal battery (LMB), which is one of the most attractive candidates for the next generation high-density energy storage systems. Electrolyte formulation and structure determine the physical properties of the electrolytes and their interfacial chemistries on the electrode surfaces. Localized high-concentration electrolytes (LHCEs) outperform state-of-the-art carbonate electrolytes in many aspects in LMBs due to their unique solvation structure. Types of fluorinated co-solvents used in LHCEs are investigated here in searching for the most suitable diluent for high concentration electrolytes (HCEs). Non-solvating solvents (including fluorinated ethers, fluorinated borate and fluorinated orthoformate) added in HCEs enable the formation of LHCEs with high-concentration solvation structures. However, low solvating fluorinated carbonate will coordinate with Li+ ions and form a second solvation shell or a pseudo-LHCE which diminishes the benefits of LHCE. In addition, it is evident that the diluent has significant influence on the electrode/electrolyte interphases (EEIs) beyond retaining the high-concentration solvation structures. Diluent molecules surrounding the high-concentration clusters could accelerate or decelerate the anion decomposition through co-participation of diluent decomposition in the EEI formation. The varied interphase features lead to significantly different battery-performance. This study points out the importance of diluents and their synergetic effects with the conductive salt and the solvating solvent in designing LHCEs. These systematic comparisons and fundamental insights into LHCEs using different types of fluorinated solvents can guide further development of advanced electrolytes for high-voltage LMBs.

Cao, Xia↗
DOE OSTI2021

Mesoscale-architecture-based crack evolution dictating cycling stability of advanced lithium ion batteries

The cracking phenomenon of Ni-rich NMC (LiNixMnyCo1-x-yO2, x = 0.6) secondary particles is frequently discovered and believed to be one of critical reasons deteriorating the long-term cycling stability of NMC cathode in lithium ion batteries (LIBs). However, the initiation and evolution of those cracks is still controversial due to the limited quantification especially by in situ monitoring, leading to the challenge of identifying an efficient approach to inhibit the formation of the fractures during repeated cycling. Herein, the irreversible, anisotropic cycling lattice and mesoscale expansion/shrinkage of nano-grain during the first cycle, as revealed by in situ X-ray diffraction (XRD) and in situ atomic force microscopy (AFM), have been quantified and confirmed to be the dominant driving forces of microcracks initiation at the grain boundaries. These microcracks preferentially nucleates at the core region with random oriented nano-grains in early stage. The further growth and aggregation of microcracks into macrocrack eventually results in microfracture propagation radially outward to the periphery region with more uniform nano-grain orientation. This mesoscale nano-grain architecture controlled cracking process highlight the importance of predictive synthesis of cathode materials with controllable multiscale crystalline architecture for high-performance LIBs.

25 ENERGY STORAGE↗
DOE OSTI2020

Evolution of the Rate-Limiting step: From Thin Film to Thick Ni-rich Cathodes

Ni-rich NMC (LiNixMnyCo1-x-yO2, x = 0.6) has the attributes of high specific capacity (greater than 180 mAh g-1), high operating voltage (ca. 3.8 V) and low cost, which is therefore deemed as one of the most promising cathode candidates for next-generation high-energy Li-ion batteries (LIBs). However, challenges exist before the large-scale commercialization of Ni-rich cathode such as gas generation, capacity degradation especially at high rate or elevated temperatures. From thin film to densely pack high loading cathode, this work investigates the rate-limiting steps in Ni-rich cathodes e.g., phase structure, electronic and ionic conductivity to understand the reaction kinetics at different scales. This work provides new insights in understanding the electrochemical properties of Ni-rich cathode at different levels to inspire revolutionary ideas to address the fundamental issues of Ni-rich cathode from materials to relevant electrode levels.

Hu, Jiangtao↗