Search NASA⌕ Search

Engineering topics

Hu, S X

Publications and source records attributed to Hu, S X.

At least 19 records

Spherical shock-ignition experiments with the 40 + 20-beam configuration on OMEGA

Spherical shock-ignition experiments on OMEGA used a novel beam configuration that separates low-intensity compression beams and high-intensity spike beams. Significant improvements in the performance of plastic-shell, D 2 implosions were observed with repointed beams. The analysis of the coupling of the high-intensity spike beam energy into the imploding capsule indicates that absorbed hot-electron energy contributes to the coupling. The backscattering of laser energy was measured to reach up to 36% at single-beam intensities of ~ 8 x 10 15 W/cm/ 2 . Hard x-ray measurements revealed a relatively low hot-electron temperature of ~30 keV independent of intensity and timing. At the highest intensity, stimulated Brillouin scattering occurs near and above the quarter-critical density and the two-plasmon-decay instability is suppressed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Rayleigh-Taylor-induced magnetic fields in laser-irradiated plastic foils

Experimental observations of magnetic fields generated by Rayleigh-Taylor growth in laser-irradiated planar foils are presented. X-ray and monoenergetic proton radiographic techniques were used to probe plastic foils with seeded surface perturbations at different times during the evolution. Protons deflected by fields in the target cause modulations in proton fluence at the seed wavelength of 120 {mu}m. Path-integrated magnetic-field strengths were inferred from modulations in proton fluence using a discrete-Fourier-transform analysis technique and found to increase from 10 to 100 T-{mu}m during linear growth. Electron thermal conduction was shown to be unaffected by Rayleigh-Taylor-induced magnetic fields during the linear growth phase.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Study of Rayleigh–Taylor growth in directly driven cryogenic-deuterium targets

Direct-drive, Rayleigh–Taylor growth experiments in liquid deuterium (D2) were performed on the OMEGA laser [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] using planar cryogenic targets at a laser intensity of ∼4 × 1014 W/cm2. These are the first Rayleigh–Taylor measurements in deuterium at conditions relevant to inertial confinement fusion using a mass preimposed initial modulation. The measured modulation optical depths are in agreement with the 2D hydrodynamics code DRACO using flux-limited local thermal transport, providing an important step in the experimental validation of simulations for direct-drive ignition.

Hager, J. D.↗

Burning plasmas with ultrashort soft-x-ray flashing

Fast ignition with narrow-band coherent x-ray pulses has been revisited for cryogenic deuterium-tritium (DT) plasma conditions achieved on the OMEGA Laser System. In contrast to using hard-x-rays (hv = 3–6 keV) proposed in the original x-ray fast-ignition proposal, we find that soft-x-ray sources with hv ≈ 500 eV photons can be suitable for igniting the dense DT-plasmas achieved on OMEGA. Two-dimensional radiation–hydrodynamics simulations have identified the break-even conditions for realizing such a “hybrid” ignition scheme (direct-drive compression with soft-x-ray heating) with 50-μm-offset targets: ∼10 ps soft-x-ray pulse (hv ≈ 500 eV) with a total energy of 500–1000 J to be focused into a 10 μm spot-size. A variety of x-ray pulse parameters have also been investigated for optimization. It is noted that an order of magnitude increase in neutron yield has been predicted even with x-ray energy as low as ∼50 J. Scaling this idea to a 1 MJ large-scale target, a gain above ∼30 can be reached with the same soft-x-ray pulse at 1.65 kJ energy. Even though such energetic x-ray sources do not currently exist, we hope that the proposed ignition scheme may stimulate efforts on generating powerful soft-x-ray sources in the near future.

Hu, S. X.↗

Experimental reduction of laser imprinting and Rayleigh–Taylor growth in spherically compressed, medium-Z-doped plastic targets

The effect of medium-Z doping of plastic ablators on laser imprinting and Rayleigh–Taylor (RT) instability growth was studied using spherical direct-drive implosions on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1977)]. The targets were spherical plastic (CH) shells, with an outer diameter of 860 μm and a thickness of 22 μm, volume doped with a varied concentration of Si (4.3% and 7.4%) and Ge (3.9%). The targets were imploded with 48 beams with a low-adiabat, triple-picket laser shape pulse with a peak intensity of 4×1014W/cm2, and a pulse duration of 2.5 ns. The shells were x-ray radiographed through a 40 -μm opening in the side of the target. The results show that volumetric impurity doping strongly reduces the shell density modulation and the instability growth rate. The amplitude of the initial imprint is reduced by a factor of 2.5 ±0.5 for CH[4.3% Si] targets and by a factor of 3 ±0.5 for CH[7.4% Si] and CH[3.9% Ge] targets. At the end of the acceleration phase, the reduction factor becomes 3 ±0.5 and 5 ± 0.5, correspondingly. The RT instability growth rate in doped targets is reduced by a factor of 1.5 compared to undoped ones. Simulations using the two-dimensional, radiation-hydrodynamics code draco show good agreement with the measurements

Fiksel, G.↗

Fast-electron generation in long-scale-length plasmas

Long-scale-length ({approx}400-{mu}m) planar CH plasmas have been generated on OMEGA EP with laser intensities of the order of 10{sup 14} W/cm{sup 2} and {approx}1-mm focal spots to quantify the number and temperature of fast electrons caused by the two-plasmon-decay instability. The main diagnostics were the time-integrated K{sub {alpha}} line emission and the hard x-ray bremsstrahlung (HXR) from a molybdenum (Mo) substrate. For the intensity range of 1-7 x 10{sup 14} W/cm{sup 2}, the Mo K{sub {alpha}} and HXR energies increased by more than three orders of magnitude. The fast-electron temperature in this range (deduced from the x-ray bremsstrahlung emission) rose from {approx}20 keV to {approx}90 keV. A Monte Carlo code was used to estimate the total energy (or number) of fast electrons based on these two experimental signatures. The resulting energy in fast electrons as a fraction of the laser energy was found to rise in the same intensity range up to {approx}1%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Multiple spherically converging shock waves in liquid deuterium

To achieve ignition, inertial confinement fusion target designs use a sequence of shocks to compress the target before it implodes. To minimize the entropy acquired by the fuel, the strength and timing of these shocks will be precisely set during a series of tuning experiments that adjust the laser pulse to achieve optimal conditions. We report measurements of the velocity and timing of multiple, converging shock waves inside spherical targets filled with liquid (cryogenic) deuterium. These experiments produced the highest reported shock velocity observed in liquid deuterium (U{sub s} = 135 km/s at {approx}25 Mb) and observed an increase in shock velocity due to spherical convergence. These direct-drive experiments are best simulated when hydrodynamic codes use a nonlocal model for the transport of absorbed laser energy from the coronal plasma to the ablation surface.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Velocity and Timing of Multiple Spherically Converging Shock Waves in Liquid Deuterium

The fuel entropy and required drive energy for an inertial confinement fusion implosion are set by a sequence of shocks that must be precisely timed to achieve ignition. This Letter reports measurements of multiple spherical shock waves in liquid deuterium that facilitate timing inertial confinement fusion shocks to the required precision. These experiments produced the highest shock velocity observed in liquid deuterium (U{sub s}=135 km/s at {approx}2500 GPa) and also the first observation of convergence effects on the shock velocity. Simulations model the shock-timing results well when a nonlocal transport model is used in the coronal plasma.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Attosecond timing the ultrafast charge-transfer process in atomic collisions

By solving the three-dimensional, time-dependent Schroedinger equation, we have demonstrated that the ultrafast charge-transfer process in ion-atom collisions can be mapped out with attosecond extreme uv (xuv) pulses. During the dynamic-charge transfer from the target atom to the projectile ion, the electron coherently populates the two sites of both nuclei, which can be viewed as a 'short-lived' molecular state. A probing attosecond xuv pulse can instantly unleash the delocalized electron from such a ''transient molecule,'' so that the resulting photoelectron may exhibit a ''double-slit'' interference. On the contrary, either reduced or no photoelectron interference will occur if the attosecond xuv pulse strikes well before or after the collision. Therefore, by monitoring the photoelectron interference visibility, one can precisely time the ultrafast charge-transfer process in atomic collisions with time-delayed attosecond xuv pulses.

74 ATOMIC AND MOLECULAR PHYSICS↗

Two-dimensional simulations of the neutron yield in cryogenic deuterium-tritium implosions on OMEGA

Maximizing the neutron yield to obtain energy gain is the ultimate goal for inertial confinement fusion. Nonuniformities seeded by target and laser perturbations can disrupt neutron production via the Rayleigh-Taylor instability growth. To understand the effects of perturbations on the neutron yield of cryogenic DT implosions on the Omega Laser Facility [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)], two-dimensional DRACO[P. B. Radha et al., Phys. Plasmas 12, 056307 (2005)] simulations have been performed to systematically investigate each perturbation source and their combined effects on the neutron-yield performance. Two sources of nonuniformity accounted for the neutron-yield reduction in DRACO simulations: target offset from the target chamber center and laser imprinting. The integrated simulations for individual shots reproduce the experimental yield-over-clean (YOC) ratio within a factor of 2 or better. The simulated neutron-averaged ion temperatures <T{sub i}> is only about 10%-15% higher than measurements. By defining the temperature-over-clean, its relationship to YOC provides an indication of how much the hot-spot volume and density are perturbed with respect to the uniform situation. Typically, the YOC in OMEGA experiments is of the order of {approx}5%. The simulation results suggest that YOC can be increased to the ignition hydroequivalent level of 15%-20% (with <{rho}R>=200-300 mg/cm{sup 2}) by maintaining a target offset of less than 10 {mu}m and employing beam smoothing by spectral dispersion.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Strong Coupling and Degeneracy Effects in Inertial Confinement Fusion Implosions

Accurate knowledge about the equation of state (EOS) of deuterium is critical to inertial confinement fusion (ICF). Low-adiabat ICF implosions routinely access strongly coupled and degenerate plasma conditions. Using the path integral Monte Carlo method, we have derived a first-principles EOS (FPEOS) table of deuterium. It is the first ab initio EOS table which completely covers typical ICF implosion trajectory in the density and temperature ranges of {rho}=0.002-1596 g/cm{sup 3} and T=1.35 eV-5.5 keV. Discrepancies in internal energy and pressure have been found in strongly coupled and degenerate regimes with respect to SESAME EOS. Hydrodynamics simulations of cryogenic ICF implosions using the FPEOS table have indicated significant differences in peak density, areal density ({rho}R), and neutron yield relative to SESAME simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Optimizing the FEDVR-TDCC Code for Exploring the Quantum Dynamics of Two-Electron Systems in Intense Laser Pulses

To efficiently solve the three-dimensional (3D) time-dependent linear and nonlinear Schrödinger equation, we have developed a large-scale parallel code RSP-FEDVR [B. I. Schneider, L. A. Collins, and S. X. Hu, Phys. Rev. E 73, 036708 (2006)], which combines the finite-element discrete variable representation (FEDVR) with the real-space product algorithm. Using the similar algorithm, we have derived an accurate approach to solve the time-dependent close-coupling (TDCC) equation for exploring two-electron dynamics in linearly polarized intense laser pulses. However, when the number N of partial waves used for the TDCC expansion increases, the FEDVR-TDCC code unfortunately slows down, because the potential-matrix operation scales as ~O(N^2). In this paper, we show that the full potential-matrix operation can be decomposed into a series of small-matrix operations utilizing the sparse property of the N N potential matrix. Such optimization speeds up the FEDVR-TDCC code by an order of magnitude for N=256. This may facilitate the ultimate solution to the 3D two-electron quantum dynamics in ultrashort intense optical laser pulses, where a large number of partial waves are required.

Hu, S X↗

Shock-tuned cryogenic-deuterium-tritium implosion performance on Omega

Cryogenic-deuterium-tritium (DT) target compression experiments with low-adiabat (alpha), multiple-shock drive pulses have been performed on the Omega Laser Facility [T. R. Boehly, D. L. Brown, R. S. Craxton et al., Opt. Commun. 133, 495 (1997)] to demonstrate hydrodynamic-equivalent ignition performance. The multiple-shock drive pulse facilitates experimental shock tuning using an established cone-in-shell target platform [T. R. Boehly, R. Betti, T. R. Boehly et al., Phys. Plasmas 16, 056301 (2009)]. These shock-tuned drive pulses have been used to implode cryogenic-DT targets with peak implosion velocities of 3x10{sup 7} cm/s at peak drive intensities of 8x10{sup 14} W/cm{sup 2}. During a recent series of alphaapprox2 implosions, one of the two necessary conditions for initiating a thermonuclear burn wave in a DT plasma was achieved: an areal density of approximately 300 mg/cm{sup 2} was inferred using the magnetic recoil spectrometer [J. A. Frenje, C. K. Li, F. H. Seguin et al., Phys. Plasmas 16, 042704 (2009)]. The other condition--a burn-averaged ion temperature <T{sub i}>{sub n} of 8-10 keV--cannot be achieved on Omega because of the limited laser energy; the kinetic energy of the imploding shell is insufficient to heat the plasma to these temperatures. A <T{sub i}>{sub n} of approximately 3.4 keV would be required to demonstrate ignition hydrodynamic equivalence [Betti et al., Phys. Plasmas17, 058102 (2010)]. The <T{sub i}>{sub n} reached during the recent series of alphaapprox2 implosions was approximately 2 keV, limited primarily by laser-drive and target nonuniformities. Work is underway to improve drive and target symmetry for future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Demonstration of the Highest Deuterium-Tritium Areal Density Using Multiple-Picket Cryogenic Designs on OMEGA

The performance of triple-picket deuterium-tritium cryogenic target designs on the OMEGA Laser System [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] is reported. These designs facilitate control of shock heating in low-adiabat inertial confinement fusion targets. Areal densities up to 300 mg/cm{sup 2} (the highest ever measured in cryogenic deuterium-tritium implosions) are inferred in the experiments with an implosion velocity {approx}3x10{sup 7} cm/s driven at peak laser intensities of 8x10{sup 14} W/cm{sup 2}. Extension of these designs to ignition on the National Ignition Facility [J. A. Paisner et al., Laser Focus World 30, 75 (1994)] is presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Neutron Yield Study of Direct-Drive, Low-Adiabat Cryogenic D2 Implosions on OMEGA Laser System

Neutron yields of direct-drive, low-adiabat (alpha ~~ 2 to 3) cryogenic D2 target implosions on the OMEGA laser system [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)] have been systematically investigated using the two-dimensional (2D) radiation hydrodynamics code DRACO [P. B. Radha et al., Phys. Plasmas 12, 056307 (2005)]. Low-mode (ell <- 12) perturbations, including initial target offset, ice-layer roughness, and laser-beam power imbalance, were found to be the primary source of yield reduction for thin-shell (5 um), low-alpha, cryogenic targets. The 2D simulations of thin-shell implosions track experimental measurements for different target conditions and peak laser intensities ranging from 2.5 x 10^14–6 x 10^14 W/cm^2. Simulations indicate that the fusion yield is sensitive to the relative phases between the target offset and the ice-layer perturbations. The results provide a reasonable good guide to understanding the yield degradation in direct-drive, low-adiabat, cryogenic, thin-shell-target implosions. Thick-shell (10 um) implosions generally give lower yield over clean than low-ell-mode DRACO simulation predictions. Simulations including the effect of laser-beam nonuniformities indicate that high-ell-mode perturbations caused by laser imprinting further degrade the neutron yield of thick-shell implosions. To study ICF compression physics, these results suggest a target specification with a <-30 um offset and ice-roughness of sigma_rms < 3 um are required.

Hu, S X↗

Spherical Rayleigh-Taylor growth of three-dimensional broadband perturbations on OMEGA

Spherical Rayleigh-Taylor (RT) growth experiments of three-dimensional (3D) broadband nonuniformities were conducted in the acceleration phase of spherical implosions on OMEGA [T. R. Boehly et al., Opt. Commun. 133, 495 (1997)]. The targets consisted of 20- and 24-{mu}m-thick plastic spherical shells having diagnostic openings for backlighter x rays to image shell modulations. Experiments were conducted with square laser pulses at a low drive intensity of {approx}2x10{sup 14} W/cm{sup 2}, high drive intensity of {approx}1x10{sup 15} W/cm{sup 2}, and a shaped pulse consisting of a low-intensity foot and high-intensity drive part (peak intensity of {approx}1x10{sup 15} W/cm{sup 2}). In low-intensity experiments, large RT growth was measured, resulting in shells being broken up by 3D modulations at the end of the drive. In the high-intensity experiments, no RT growth of the 3D modulations was detected. In the shaped-pulse experiments, perturbations grew during the low-intensity part of the drive and were stabilized later during the high-intensity part of the drive. The measured RT growth stabilization with the high-intensity drive was similar to previous observations in planar geometry [V. A. Smalyuk et al., Phys. Rev. Lett. 101, 025002 (2008)].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗