Search NASA⌕ Search

Engineering topics

Hua, Zilong

Publications and source records attributed to Hua, Zilong.

At least 19 records

Impacts of point defects on shallow doping in cubic boron arsenide: A first principles study

Cubic boron arsenide (BAs) stands out as a promising material for advanced electronics, thanks to its exceptional thermal conductivity and ambipolar mobility. However, effective control of p- and n-type doping in BAs poses a significant challenge, mostly as a result of the influence of defects. In the present study, we employed density functional theory (DFT) to explore the impacts of the common point defects and impurities on p-type doping of Be B and Si As , and on n-type doping of Si B and Se As . We found that the most favorable point defects formed by C, O, and Si are C As , O B O As , Si As , C As Si B , and O B Si As , which have formation energies of less than 1.5 eV. While the O impurity detrimentally affects both p- and n-type dopings, C and Si impurities are harmful for n-type dopings, making n-type doping a potential challenge. Interestingly, the antisite defect pair A s B B As benefits both p- and n-type doping. Finally, the doping limitation analysis presented in this study can potentially pave the way for strategic development in the area of BAs-based electronics.

36 MATERIALS SCIENCE↗

Impact of classical statistics on thermal conductivity predictions of BAs and diamond using machine learning molecular dynamics

Machine learning interatomic potentials (MLIPs) have greatly enhanced molecular dynamics (MD) simulations, achieving near-first-principles accuracy in thermal conductivity studies. In this work, we reveal that this accuracy, observed in BAs and diamond at sub-Debye temperatures, stems from an accidental error cancelation: classical statistics overestimates specific heat while underestimating phonon lifetimes, balancing out in thermal conductivity predictions. However, this balance is disrupted when isotopes are introduced, leading MLIP-based MD to significantly underpredict thermal conductivity compared to experiments and quantum statistics-based Boltzmann transport equation. This discrepancy arises not from classical statistics affecting phonon–isotope scattering rates but from its impact on the interplay between phonon–isotope and phonon–phonon scattering in the normal scattering-dominated BAs and diamond. In conclusion, this work underscores the limitations of MLIP-based MD for thermal conductivity studies at sub-Debye temperatures.

36 MATERIALS SCIENCE↗

Experimental investigation of thermal conductivity of high entropy ceramics

In this talk, we will present the experimental investigation of thermal conductivity of high entropy carbides (HEC) and borides (HEB) with different compositions. Thermal conductivity determines the capability of a material to transport thermal energy and is considered as one critical physical property, specially in the energy industry. Due to the presences of disordered cation sublattice, it is expected that thermal conductivity of high entropy ceramics is lower than the counterparts with simpler compositions, but the experimental studies are relatively few. Using laser-based spatial-domain and frequency-domain thermoreflectance technique, we measured thermal conductivity of HECs and HEBs in a temperature range from 77K to 773K. Furthermore, by focusing the laser using an objective lens, we were able to perform the thermal property mapping on samples with the spatial resolution of micrometer. Such measurements could reveal important microstructure information in a rapid and efficient way without using scanning electron microscopy. The high spatial resolution also enables thermal conductivity measurements on ion-irradiated HECs with the damage layer of merely 1.1µm. These measurements can provide valuable information to predict the performances of HECs and HEBs with different compositions and from different manufacturing processes, and in the extreme environments such as nuclear reactors.

36 - MATERIALS SCIENCE↗

Results of Post-Process NDE Using Advanced Techniques on AM Parts

The purpose of this report is to provide an overview of the FY24 activities to apply advanced nondestructive examination (NDE) methods to materials and components produced using advanced manufacturing (AM) processes such as Laser Powder Bed Fusion (LPBF) and Direct Energy Deposition (DED) and assess the challenges of examining these materials to identify defects and microstructure variations. This work was performed as part of the U.S. Department of Energy‘s Office of Nuclear Energy Advanced Materials and Manufacturing Technologies (AMMT) Program. The primary mission of the AMMT program is to develop advanced materials and manufacturing technologies that enable both the current fleet and the next generation of advanced nuclear reactors to operate safely and economically, and to maintain U.S. leadership in technology development for nuclear energy systems.

36 MATERIALS SCIENCE↗

Advanced Materials and Manufacturing Technologies Nondestructive Examination Efforts at Idaho National Laboratory: Report of FY-24 Efforts

This report details FY-24 nondestructive examination (NDE) efforts at Idaho National Laboratory (INL) in support of the Advanced Materials and Manufacturing Technologies (AMMT) program. While the goal of this endeavor is to develop a multi-modal, multi-length scale workflow for nondestructive characterization of advanced manufactured (AM) nuclear reactor components, substantial development remains until this is a reality. In support of this effort X-ray computed tomography (XCT), X-ray diffraction (XRD), neutron computed tomography (nCT), neutron diffraction, lock-in thermography (LIT), multi-point lock-in thermography (MLIT), and positron annihilation spectroscopy (PAS) were all used on AM specimens to examine defects such as voids, porosity, and residual stress. In addition to summarizing the results of these NDE applications, recommendations for integrating these into a more comprehensive undertaking to promote NDE of engineering-scale components are also included.

36 MATERIALS SCIENCE↗

Embedded Fiber Optic Sensors in Structural Materials for Sensing in Extreme Environments

This slide deck presents the research results in embedding fiber optic sensors in structural materials. Fiber optic sensors were embedded in stainless steel and nickel via electric field assisted sintering. The embedded sensors were evaluated in terms of fiber integrity, fiber-matrix bonding, fiber functionality, mechanical properties, and machinability.

36 - MATERIALS SCIENCE↗

Selective laser sintering and spark plasma sintering of (Zr,Nb,Ta,Ti,W)C compositionally complex carbide ceramics

Abstract Two advanced manufacturing processes, spark plasma sintering (SPS) and selective laser sintering (SLS), have been developed for synthesis of (Zr,Nb,Ta,Ti,W)C compositionally complex carbide (CCC) via reactive sintering of a powder mixture of constitute monocarbides. X‐ray diffraction analysis confirmed that the single‐phase CCC can be formed by both SPS and SLS. While a homogenous microstructure with uniform metal element distributions was developed during SPS, three‐layer microstructures with a thin TiC‐rich layer and two TaC‐rich layers along with a TiO 2 ‐rich surface layer containing W nanoparticles were formed during SLS. In addition, cellular structures with W, Zr, and Ti element segregation and dislocations on cell boundaries were observed in the SLS‐CCC sample, indicating the effect of nonequilibrium conditions on microstructure formation during laser melting followed by rapid cooling and solidification process. Compared to the SPS‐CCC sample, the SLS‐CCC showed enhanced hardness and reduced thermal conductivity, which may be related to their unique cellular structures.

36 MATERIALS SCIENCE↗

Compositionally complex carbide ceramics: A perspective on irradiation damage

Extensive experimental and computational studies have demonstrated outstanding physical and chemical properties of the novel materials of compositionally complex carbides (CCCs), enabling their promising applications in advanced fission and fusion energy systems. This perspective provides a comprehensive overview of radiation damage behavior reported in the literature to understand the fundamental mechanisms related to the impact of multi-principal metal components on phase stability, irradiation-induced defect clusters, irradiation hardening, and thermal conductivity of compositionally complex carbides. Several future research directions are recommended to critically evaluate the feasibility of designing and developing new ceramic materials for extreme environments using the transformative “multi-principal component” concept. Compared to the existing materials for nuclear applications including stainless steels, nickel alloys, ZrC, SiC, and potentially high-entropy alloys, as well as certain other compositionally complex ceramic families. CCCs appear to be more resistant to amorphization, growth of irradiation defect clusters, and void swelling.

36 MATERIALS SCIENCE↗

Accelerated thermal property mapping of TRISO advanced nuclear fuel

TRistructural ISOtropic (TRISO) fuel is a leading-edge nuclear fuel form representing a departure from the more traditional nuclear fuel forms utilized in the reactor fleet of today. Rather than a monolithic fuel pellet of uranium dioxide, integral fuel forms containing TRISO fuel are composed of thousands of microencapsulated uranium-bearing fuel kernels and individually coated with multiple layers of pyrolytic carbon and silicon carbide. These multilayered ceramic coatings serve as an environmental barrier to ensure radioactive and chemically reactive fission products are contained within the reactor fuel elements, but also participate in the transfer of heat generated in the nuclear fuel to the coolant – the primary purpose of a nuclear reactor. Since traditional thermal property measurement techniques, such as laser flash analysis, would be unable to resolve the thermal properties of the individual TRISO coating layers, a simplified frequency-domain thermoreflectance technique has been developed to rapidly map the thermal properties of TRISO particles. Using this technique, the thermal properties of TRISO particles have been mapped from room temperature up to 1000 °C to examine the spatial variation and temperature-dependency of the thermal properties within each layer. Additionally, spatial-domain thermoreflectance was used to examine the anisotropy of the thermal properties for each layer at different locations within a single TRISO particle, and across multiple TRISO particles to assess the intra- and inter-particle uniformity of thermal properties, respectively. To elucidate the underlying causes for the measured variations in thermal properties, scanning electron microscopy and Raman spectroscopy were used to examine variations in microstructure and chemical bonding within the different coating layers. Results from this work are then compared with previous examinations of TRISO fuel particles and microstructurally driven mechanisms for the variations in the measured thermal properties of the different carbonaceous layers are discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Extreme sensitivity of higher-order interatomic force constants and thermal conductivity to the energy surface roughness of exchange-correlation functionals

In this Letter, we report that the fourth-order interatomic force constants (4th-IFCs) are significantly sensitive to the energy surface roughness of exchange-correlation (XC) functionals in density functional theory calculations. This sensitivity, which is insignificant for the second- (2nd-) and third-order (3rd-) IFCs, varies for different functionals in different materials and can cause misprediction of thermal conductivity by several times of magnitude. As a result, when calculating the 4th-IFCs using the finite difference method, the atomic displacement needs to be taken large enough to overcome the energy surface roughness, in order to accurately predict phonon lifetime and thermal conductivity. We demonstrate this phenomenon on a benchmark material (Si), a high-thermal conductivity material (BAs), and a low thermal conductivity material (NaCl). For Si, we find that the LDA, PBE, and PBEsol XC functionals are all smooth to the 2nd- and 3rd-IFCs but all rough to the 4th-IFCs. This roughness can lead to a prediction of nearly one order of magnitude lower thermal conductivity. For BAs, all three functionals are smooth to the 2nd- and 3rd-IFCs, and only the PBEsol XC functional is rough for the 4th-IFCs, which leads to a 40% underestimation of thermal conductivity. For NaCl, all functionals are smooth to the 2nd- and 3rd-IFCs but rough to the 4th-IFCs, leading to a 70% underprediction of thermal conductivity at room temperature. In conclusion, with these observations, we provide general guidance on the calculation of 4th-IFCs for an accurate thermal conductivity prediction.

42 ENGINEERING↗

Integrating fiber optic sensors into metallic components for sensing in harsh environments

The integration of fiber optic sensors into high-temperature materials is critical for real-time monitoring and autonomous operation of engineering systems. This study demonstrated a spark plasma sintering (SPS)-assisted embedding process for integrating sapphire fiber optic sensors into stainless steel components during part fabrication. Optical fibers were encapsulated in stainless steel 316L powders which were sintered at different fabrication conditions using SPS to investigate the effects of sintering parameters on the embedment. Measurements of optical transmittance, combined with microstructural analysis (X-ray computed tomography and scanning electron microscopy) and mechanical testing (tensile and microhardness), were conducted to examine the fiber functionality, fiber–matrix bonding quality, and properties of the sintered materials. Here, the results show that under suitable fabrication conditions, intact optical fibers can be encapsulated in highly-densified (>98 % relative density) stainless steel components. These conditions also led to a good bond at the fiber–matrix interface with micron-sized material interdiffusion across the interface. The sintering parameters were observed to affect fiber optical attenuation, where high temperature, pressure, and hold time during SPS enhanced fiber–matrix bonding and adversely affected optical transmission. Tensile testing confirmed the superior tensile strength and ductility of the matrix fabricated by SPS. Furthermore, the materials exhibited limited strength reduction (~70 MPa) upon the integration of fibers. This study demonstrates the effectiveness of SPS for fiber-material integration for high-temperature applications.

36 MATERIALS SCIENCE↗

Initial Results of PostProcess NDE Using Advanced Techniques

The U.S. Department of Energy, Office of Nuclear Energy Advanced Materials and Manufacturing Technologies Program is developing advanced materials and manufacturing technologies that will enable the safe and economical operation of both the current fleet and the next generation of advanced nuclear reactors. Post-process nondestructive evaluation capabilities are a key enabling technology that will be required to qualify and verify the condition of components produced using advanced materials and manufacturing technologies.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Impacts of irradiation-induced nanostructure on phonon linewidths and thermal conductivity in U-Zr alloy

Ion irradiation can significantly change material properties. Thermal conductivity degradation of reactor fuel is detrimental to safety and efficiency—driving research on how irradiation impacts heat-carrying phonons. Here, we report the measurements of phonon dispersion and lifetimes (inverse linewidths) in freestanding irradiated crystals and reveal the relationship between thermal conductivity and proton irradiation induced nanostructures in UZr 2.6 using inelastic x-ray scattering, electron microscopy, modulated thermoreflectance, and first-principles calculations. Irradiation results in more significant increases in phonon linewidths and decreased thermal conductivity in the basal plane than that along the c axis, decreasing thermal conductivity anisotropy. Furthermore, microscopy reveals that this results from irradiation induced nanoprecipitates and metastable phase separation. Surprisingly, irradiation leads to smaller phonon linewidths near some zone boundaries, which we attribute to irradiation induced short-range order.

36 MATERIALS SCIENCE↗

Microstructure characterization of electric field assisted sintering (EFAS) sintered metallic and ceramic materials using local thermal diffusivity measurement

Electric Field Assisted Sintering (EFAS, also referred to as spark plasma sintering) is a powerful technology for the consolidation of powder materials. The high heating rate during the sintering process is critical for minimizing energy consumption, but it can also cause microstructure heterogeneities in sintered parts, such as spatially varied porosity. The examination of localized porosity usually requires the use of a scanning electron microscope with a carefully prepared surface. In this paper, photothermal radiometry is used to measure local thermal diffusivity and extract localized porosity of EFAS-sintered parts by using a percolation-threshold model. Applying this approach, we identified the radial position-dependent porosity variation in EFAS parts, which is likely formed due to the large temperature gradient during the sintering process. This approach has a unique advantage because it can measure samples with minimal or no surface preparation, enabling the possibility of in situ characterization in EFAS with proper system modification. Necessary modifications on the measurement approach for EFAS deployment and in situ characterization are also discussed.

36 MATERIALS SCIENCE↗

Nondestructive property and defect characterization using X-rays and neutrons

As advanced manufacturing (AM) continues to mature as a fabrication technique, interest in its use for the fabrication of nuclear components continues to grow. AM nuclear parts offer the ability to create parts with complex and non-standard geometries that cannot be produced using traditional manufacturing techniques, circumvention of supply chain issues, and reduction of time from design to implementation. However, components fabricated with AM techniques must undergo nondestructive examination (NDE) to ensure they are fabricated to the required specifications to ensure safe and proper operation. The Advanced Materials and Manufacturing Technologies (AMMT) program has undertaken initial exploratory studies on several NDE techniques to evaluate their feasibility for research and development (R&D), as well as Quality Assurance and Quality Control (QA/QC), and in-service inspections of AM parts. This work describes research results on several techniques, including X-ray and neutron tomography and scattering, as well as photothermal radiometry. The experimental results are described and an overview for each techniques’ potential use on AM parts in the various phases of part development and lifetime is given. Finally, future directions for technique development and application to AM nuclear components are described.

36 MATERIALS SCIENCE↗