Engineering topics

Huang, John

Publications and source records attributed to Huang, John.

At least 19 records

NASA NTRS2012

Wind Tunnel Testing of a One-Dimensional Laser Beam Scanning and Laser Sheet Approach to Shock Sensing

A 15- by 15-cm supersonic wind tunnel application of a one-dimensional laser beam scanning approach to shock sensing is presented. The measurement system design allowed easy switching between a focused beam and a laser sheet mode for comparison purposes. The scanning results were compared to images from the tunnel Schlieren imaging system. The tests revealed detectable changes in the laser beam in the presence of shocks. The results lend support to the use of the one-dimensional scanning beam approach for detecting and locating shocks in a flow, but some issues must be addressed in regards to noise and other limitations of the system.

Tokars, Roger↗

NASA NTRS2009

Wide-Angle-Scanning Reflectarray Antennas Actuated by MEMS

An effort to develop large-aperture, wide-angle-scanning reflectarray antennas for microwave radar and communication systems is underway. In an antenna of this type as envisioned, scanning of the radiated or incident microwave beam would be effected through mechanical rotation of the passive (reflective) patch antenna elements, using microelectromechanical systems (MEMS) stepping rotary actuators typified by piezoelectric micromotors. It is anticipated that the cost, mass, and complexity of such an antenna would be less than, and the reliability greater than, those of an electronically scanned phased-array antenna of comparable beam-scanning capability and angular resolution. In the design and operation of a reflectarray, one seeks to position and orient an array of passive patch elements in a geometric pattern such that, through constructive interference of the reflections from them, they collectively act as an efficient single reflector of radio waves within a desired frequency band. Typically, the patches lie in a common plane and radiation is incident upon them from a feed horn.

Fang, Houfei↗

NASA NTRS2008

Advanced Precipitation Radar Antenna to Measure Rainfall From Space

To support NASA s planned 20-year mission to provide sustained global precipitation measurement (EOS-9 Global Precipitation Measurement (GPM)), a deployable antenna has been explored with an inflatable thin-membrane structure. This design uses a 5.3 5.3-m inflatable parabolic reflector with the electronically scanned, dual-frequency phased array feeds to provide improved rainfall measurements at 2.0-km horizontal resolution over a cross-track scan range of up to 37 , necessary for resolving intense, isolated storm cells and for reducing the beam-filling and spatial sampling errors. The two matched radar beams at the two frequencies (Ku and Ka bands) will allow unambiguous retrieval of the parameters in raindrop size distribution. The antenna is inflatable, using rigidizable booms, deployable chain-link supports with prescribed curvatures, a smooth, thin-membrane reflecting surface, and an offset feed technique to achieve the precision surface tolerance (0.2 mm RMS) for meeting the low-sidelobe requirement. The cylindrical parabolic offset-feed reflector augmented with two linear phased array feeds achieves dual-frequency shared-aperture with wide-angle beam scanning and very low sidelobe level of -30 dB. Very long Ku and Ka band microstrip feed arrays incorporating a combination of parallel and series power divider lines with cosine-over-pedestal distribution also augment the sidelobe level and beam scan. This design reduces antenna mass and launch vehicle stowage volume. The Ku and Ka band feed arrays are needed to achieve the required cross-track beam scanning. To demonstrate the inflatable cylindrical reflector with two linear polarizations (V and H), and two beam directions (0deg and 30deg), each frequency band has four individual microstrip array designs. The Ku-band array has a total of 166x2 elements and the Ka-band has 166x4 elements with both bands having element spacing about 0.65 lambda(sub 0). The cylindrical reflector with offset linear array feeds reduces the complexity from "NxN" transmit/receive (T/R) modules of a conventional planar-phased array to just "N" T/R modules. The antenna uses T/R modules with electronic phase-shifters for beam steering. The offset reflector does not provide poor cross-polarization like a double- curved offset reflector would, and it allows the wide scan angle in one plane required by the mission. Also, the cylindrical reflector with two linear array feeds provides dual-frequency performance with a single, shared aperture. The aperture comprises a reflective surface with a focal length of 1.89 m and is made from aluminized Kapton film. The reflective surface is of uniform thickness in the range of a few thousandths of an inch and is attached to the chain-link support structure via an adjustable suspension system. The film aperture rolls up, together with the chain-link structure, for launch and can be deployed in space by the deployment of the chain-link structure.

Rahmat-Samii, Yahya↗

NASA NTRS2008

VHF Wide-Band, Dual-Polarization Microstrip-Patch Antenna

The figure depicts selected aspects of a very-high-frequency (VHF) microstrip patch antenna designed and built to satisfy requirements specific to an airborne synthetic-aperture radar system for measuring the thickness of sea ice. One of the requirements is that the antenna be capable of functioning over the relatively wide frequency band of 127 to 172 MHz corresponding to a fractional bandwidth of about 30 percent relative to a nominal mid-band frequency of 149.5 MHz. Another requirement is that the antenna be capable of functioning in either or both of two orthogonal linear polarizations. In addition, the antenna is required to be as compact and lightweight as possible. In a basic design according to generally accepted microstrip-patch-antenna engineering practice, one would ordinarily use a relatively thick dielectric substrate and multiple feed probes to obtain the desired combination of wide-band and dual-polarization capabilities. However, the combination of a thick substrate and multiple feeds would give rise to higher-order electromagnetic nodes, thereby undesirably contributing to cross polarization and to reduction of the isolation between feed probes. To counter these adverse effects while satisfying the requirements stated above, the design of this antenna incorporates several improvements over the basic design.

Huang, John↗

NASA NTRS2008

In-Space Deployable Reflectarray Antenna: Current and Future

Technologies associated with a 10-m X/Ka-band dual-frequency reflectarray antenna have been developed for deep space communication applications. The first task is the development of a 3-m diameter X/Ka dual frequency reflectarray which serves as a stepping-stone to the 10-m aperture antenna. The second task is to develop a deployable frame.

Fang, Houfei↗

NASA NTRS2007

Lightweight Reflectarray Antenna for 7.115 and 32 GHz

A lightweight reflectarray antenna that would enable simultaneous operation at frequencies near 7.115 GHz and frequencies near 32 GHz is undergoing development. More precisely, what is being developed is a combination of two reflectarray antennas -- one for each frequency band -- that share the same aperture. (A single reflectarray cannot work in both frequency bands.) The main advantage of the single dual-band reflectarray is that it would weigh less and occupy less space than do two single-band reflectarray antennas

Zawadzki, Mark↗

NASA NTRS2007

Aperture-Coupled Thin-Membrane L-Band Antenna

The upper part of the figure depicts an aperture-coupled L-band antenna comprising patterned metal conductor films supported on two thin polyimide membranes separated by an air gap. In this antenna, power is coupled from a microstrip line on the lower surface of the lower membrane, through a slot in a metal ground plane on the upper surface of the lower membrane, to a radiating metal patch on the upper surface of the upper membrane. The two-membrane configuration of this antenna stands in contrast to a three-membrane configuration heretofore considered as the basis for developing arrays of dual-polarization, wideband microwave antennas that could be thin and could be, variously, incorporated into, or supported on, thin structures, including inflatable structures. By reducing the number of membranes from three to two, the present design simplifies the problems of designing and fabricating such antennas or arrays of such antennas, including the problems of integrating such antennas or arrays with thin-membrane-mounted transmit/ receive modules. In addition, the use of aperture (slot) coupling eliminates the need for rigid coaxial feed pins and associated solder connections on thin membranes, making this antenna more mechanically reliable, relative to antennas that include coaxial feed pins. This antenna is designed for a nominal frequency of 1.26 GHz. The polyimide membranes are 0.05 mm thick and have a relative permittivity of 3.4. The radiating patch is square, 8.89 cm on each side. This radiating patch lies 1.27 cm above the ground plane. The feeding microstrip line is 0.12 mm wide and has a characteristic impedance of 50 . The aperture-coupling slot, etched in the ground plane, is 0.48 mm wide and 79.5 mm long. In order to maximize coupling, the microstrip line is extended beyond the middle of the slot by a length of 36 mm, which corresponds to a transmission- line electrical length of about a quarter wavelength. The other end of the microstrip line is transformed to a 50-Ohm coplanar waveguide line, which is used for connection to a transmit/receive module. Some plated-through vias are added to the outer conductors of the coplanar waveguide to suppress parallel-plate modes. The measured and calculated 10-dB-return-loss bandwidth of the antenna is 100 MHz. By eliminating the radiating patch and the upper membrane that supports it, and performing two other simple modifications, one can convert the two-membrane antenna described above to a paper-thin single-membrane antenna, shown in the lower part of the figure. One modification is to increase the slot length to 104.95 mm; the other is to extend the microstrip to 36.68 mm past the middle of the slot. With these modifications, the slot now becomes a half-wavelength radiator with a nearly omnidirectional radiation pattern. In one potential use, such a paper-thin antenna could be pasted on an automobile window to enable omnidirectional communication.

Huang, John↗

NASA NTRS2006

Radiation Characteristics of Reflectarray Antennas: Methodology and Applications to Dual Configurations

Reflectarrays combines key features of large reflectors and phased array elements to generate a collimated beam as required in high gain antennas. In reflectarrays, a large flat reflecting surface with many resonant patch elements is illuminated by a feed (or by a feed/subreflector in dual reflector configuration). In many space applications, reflectarrays applications can be advantageous because their large surface can be folded or rolled as a part of spacecraft payload before being deployed. Consequently, a reflectarray can significantly reduce both volume and mass requirements in space deployment. To optimize reflectarray antenna performance, a phase correction mechanism must be applied to its individual array elements some of which are well documented in the literatures. In this study, we attempt to extend analytical techniques in reflector analysis to reflectarrays by introducing a number of approaches to estimate the reflectarray antenna performance independent of its phase compensation mechanism. In one approach, a Physical Optics (PO) current will be assigned to the surface of individual reflectarray elements upon which a phase correction will be applied. In the second approach, a transmit/receive (TX/RX) radiation characteristics will be assigned to individual reflectarray elements from which coupling coefficients will be calculated and assigned as the excitation coefficient of individual elements. PO approach is modeled in the UCLA reflector code while coupling (TX/RX) method is implemented in both UCLA code as well as TICRA (GRASP) software. Results are presented for single and dual configurations with the main reflector as a reflectarray. The approach described is used to design a 3-m Cassegrain offset-fed configuration for dual X/Ka-bands application.

reflectors↗

NASA NTRS2006

High-capacity communications from Martian distances part 4 : assessment of spacecraft pointing accuracy capabilities required for large Ka-band reflector antennas

Improved surface accuracy for deployable reflectors has brought with it the possibility of Ka-band reflector antennas with extents on the order of 1000 wavelengths. Such antennas are being considered for high-rate data delivery from planetary distances. To maintain losses at reasonable levels requires a sufficiently capable Attitude Determination and Control System (ADCS) onboard the spacecraft. This paper provides an assessment of currently available ADCS strategies and performance levels. In addition to other issues, specific factors considered include: (1) use of "beaconless" or open loop tracking versus use of a beacon on the Earth side of the link, and (2) selection of fine pointing strategy (body-fixed/spacecraft pointing, reflector pointing or various forms of electronic beam steering). Capabilities of recent spacecraft are discussed.

Bassily, Samir (Sam)↗

NASA NTRS2006

Interferometric System for Measuring Thickness of Sea Ice

The cryospheric advanced sensor (CAS) is a developmental airborne (and, potentially, spaceborne) radar-based instrumentation system for measuring and mapping the thickness of sea ice. A planned future version of the system would also provide data on the thickness of snow covering sea ice. Frequent measurements of the thickness of polar ocean sea ice and its snow cover on a synoptic scale are critical to understanding global climate change and ocean circulation.

Hussein, Ziad↗

NASA NTRS2006

A Cassegrain Offset-Fed Dual-Band Reflectarray

An X/Ka dual-band microstrip reflectarray with circular polarization (CP) has been constructed using thin membranes and Cassegrain offset-fed configuration. It is believed that this is the first Cassegrain reflectarray ever been developed. This antenna has a 75-cm-diameter aperture and uses metallic subreflector and angular-rotated annular ring elements. It achieved a measured -3dB-gain bandwidth of 700 MHz at X-band and 1.5 GHz at Ka-band, as well as a CP bandwidth (3dB axial ratio) of more than 700 MHz at X-band and more than 2 GHz at Ka-band. The measured peak efficiencies are 49.8% at X-band and 48.2% at Ka-band.

offset fed↗

NASA NTRS2006

An eight-meter inflatable reflectarray antenna and its inflatable/self-rigidizable booms

This paper presents the analysis and test results related to buckling capability, modal characteristics, and thermal expansion coefficient of STR aluminum laminate inflatable/self-rigidizable booms with lengths up to 10 metes. STR booms are fundamental building blocks of space inflatable/self-rigidizable reflectarray antennas. These boom characteristics are essential for analyzing structural integrity, in orbit dynamic response, and in orbit thermal distortion of the 8-mter reflectarray antenna. Distinct advantages of the STR booms will also be identified and presented by this paper.

membranes↗

NASA NTRS2006

Large Deployable Reflectarray Antenna

A report discusses a 7-meter-diameter reflectarray antenna that has been conceived in a continuing effort to develop large reflectarray antennas to be deployed in outer space. Major underlying concepts were reported in three prior NASA Tech Briefs articles: "Inflatable Reflectarray Antennas" (NPO-20433), Vol. 23, No. 10 (October 1999), page 50; "Tape-Spring Reinforcements for Inflatable Structural Tubes" (NPO-20615), Vol. 24, No. 7 (July 2000), page 58; and "Self-Inflatable/Self-Rigidizable Reflectarray Antenna" (NPO-30662), Vol. 28, No. 1 (January 2004), page 61. Like previous antennas in the series, the antenna now proposed would include a reflectarray membrane stretched flat on a frame of multiple inflatable booms. The membrane and booms would be rolled up and folded for compact stowage during transport. Deployment in outer space would be effected by inflating the booms to unroll and then to unfold the membrane, thereby stretching the membrane out flat to its full size. The membrane would achieve the flatness for a Ka-band application. The report gives considerable emphasis to designing the booms to rigidify themselves upon deployment: for this purpose, the booms could be made as spring-tape-reinforced aluminum laminate tubes like those described in two of the cited prior articles.

Fang, Houfei↗

NASA NTRS2006

Dynamic Analysis of Large In-Space Deployable Membrane Antennas

This paper presents a vibration analysis of an eight-meter diameter membrane reflectarray antenna, which is composed of a thin membrane and a deployable frame. This analysis process has two main steps. In the first step, a two-variable-parameter (2-VP) membrane model is developed to determine the in-plane stress distribution of the membrane due to pre-tensioning, which eventually yields the differential stiffness of the membrane. In the second step, the obtained differential stiffness is incorporated in a dynamic equation governing the transverse vibration of the membrane-frame assembly. This dynamic equation is then solved by a semi-analytical method, called the Distributed Transfer Function Method (DTFM), which produces the natural frequencies and mode shapes of the antenna. The combination of the 2-VP model and the DTFM provides an accurate prediction of the in-plane stress distribution and modes of vibration for the antenna.

vibrations↗

NASA NTRS2006

High-Capacity Communications from Martian Distances Part 4: Assessment of Spacecraft Pointing Accuracy Capabilities Required For Large Ka-Band Reflector Antennas

Hodges, Richard E.↗

NASA NTRS2005

Remote sensing of sea ice thickness by a combined spatial and frequency domain interferometer : formulations, instrument design & development

The thickness of Arctic sea ice plays a critical role in Earth's climate and ocean circulation. An accurate measurement of this parameter on synoptic scales at regular intervals would enable characterization of this important component for the understanding of ocean circulation and the global heat balance. Presented in this paper is a low frequency VHF interferometer technique and associated radar instrument design to measure sea ice thickness based on the use of backscatter correlation functions. The sea ice medium is represented as a multi-layered medium consisting of snow, seaice and sea water, with the interfaces between layers characterized as rough surfaces. This technique utilizes the correlation of two radar waves of different frequencies and incident and observation angles, scattered from the sea ice medium. The correlation functions relate information about the sea ice thickness. Inversion techniques such as the genetic algorithm, gradient descent, and least square methods, are used to derive sea ice thickness from the phase information related by the correlation functions.

remote sensing↗

NASA NTRS2005

Aperture-coupled thin-membrane microstrip array antenna for beam scanning application

A microstrip array using aperture-slot-coupling technique with very thin membranes has been developed at the L-band frequency for beam scanning application. This technology-demonstration array with 4 x 2 elements achieved a relatively wide bandwidth of 100 MHz (8%) and +/-45(deg) beam scan. Very narrow coupling slots were used with each having an aspect ratio of 160 (conventional slot aspect ratio is between 10 to 30) for coupling through very thin membrane (0.05mm thickness). This thin-membrane aperture-coupling technique allows the array antenna elements to be more easily integrated with transmit/receive amplifier (T/R) and phase shifter modules. This paper addresses only the radiator portion of the array. The array and active components will be presented in a separate pape.

array antenna↗

NASA NTRS2005

A wide-band dual-polarized VHF microstrip antenna for global sensing of sea ice thickness

A VHF microstrip patch antenna was developed to achieve a bandwidth of 45 MHz (30%) from 127 MHz to 172 MHz with dual-linear-polarization capability. This microstrip antenna used foam substrates and dual stacked patches with capacitive probe feeds to achieve wide bandwidth. Four such capacitive feeds were used to achieve dual polarizations with less than -20 dB of cross-polarization level. Twenty-four shorting pins were used on the lower patch to achieve acceptable isolation between the four feed probes. This antenna has a measured gain of 8.5 dB at 137 MHz and 10 dB at 162 MHz. By using the Method of Moments technique, multipath scattering patterns were calculated when the antenna is mounted on the outside of a Twin Otter aircraft.

VHF↗