Engineering topics
Huang, Sijia
Publications and source records attributed to Huang, Sijia.
Ductile Glassy Polymer Networks Capable of Large Plastic Deformation and Heat-Induced Elastic Recovery
Many thermoplastic polymers are ductile by combining strength and large deformations. These deformations are irreversible - known as plastic deformation. Elastomers can deform reversibly but have low strength. To this end, we developed glassy and ductile polyamide networks capable of large plastic deformation (>200% strain) and high strength (~50 MPa tensile strength and ~1500 MPa Young’s modulus), similar to those of polyolefins and Nylon-66. We discovered that hydrogen bonding between meta-phthalamide groups was essential to the ductility. Since these polyamide networks are covalently bonded, we demonstrated their unique durability by repeatable elastic recovery at elevated temperatures, exhibiting indifferent tensile properties in each cycle. Furthermore, when we fixed the strain during the elastic recovery, these polyamide networks actuated stresses of 9–18 MPa, among the highest reported in shape-memory polymer actuators. Here, we envision these ductile, glassy polymer networks as promising alternatives to ductile thermoplastics, given the combined benefit of ductility and durability.
Virtual Volumetric Additive Manufacturing (VirtualVAM)
Abstract Tomographic volumetric additive manufacturing (VAM) produces arbitrary 3D geometries by exposure of a rotating volume of photopolymer resin to tomographically‐patterned illumination. This enables high speed, layer‐less printing of parts from a wide range of photopolymers not amenable to layer‐by‐layer processes. Since the entire geometry is produced at once over the course of a few seconds to minutes, molecular diffusion length scales become significant to the printing process. Understanding these molecular reaction and diffusion processes is imperative for advancing VAM to a usable technology. These processes are experimentally very difficult to monitor and measure. Herein, VirtualVAM ‐ a simulation framework for modeling the tomographic VAM process, is developed and experimentally validated. VirtualVAM simulates reaction, diffusion, and heat generation processes over the course of a print with single‐voxel resolution. From a few experimentally‐determined input parameters and a set of images for projection, VirtualVAM is able to generate a large spatio‐temporal data set for any given tomographic VAM print. Using VirtualVAM, a number of experimentally‐unattainable aspects of the VAM process are investigated such as single‐voxel conversion profiles, effect of molecular oxygen, and stopping time determination. VirtualVAM also enables the optimization of exposure patterns to further improve contrast between in‐part and out‐of‐part delivered dose.
One-pot ternary sequential reactions for photopatterned gradient multimaterials
Seamless multimaterial construction is a common motif in animal physiology. Such continuous mechanical gradients remain challenging to reproduce in engineered systems, as current resin chemistries typically result in a single fixed set of properties. As an alternative to single-property materials, we introduce a thiol-ene-epoxy-based photothermal reaction scheme that produces multimaterials by altering the polymer microstructure within a single resin. In this system, the photodosage during the first stage of processing dictates the extent of conversion for each subsequent reaction. As a result, our photochemistry can exhibit a diverse range of soft (Young’s modulus, E ~ 400 kPa; elongation, dL/L0 ~ 300%) and stiff (E ~ 1.6 GPa; dL/L 0 ~ 3%) mechanical properties. Furthermore, we pattern photostable and mechanically robust modulus gradients (d[E r, stiff /E r , soft] /dx > 1,000 mm -1 ) that exceed those found in squid beaks and human knee entheses. We demonstrate the ability to build intricate multimaterial architectures including a soft, wearable braille display.
Simple Bioparticle Filtration Device Based on an Ultralow-Fouling Zwitterionic Polyurethane Membrane for Rapid Large-Volume Separation of Plasma and Viruses from Whole Blood
Plasma separation from whole blood is oftent required as an essential first step when performing blood tests with a viral assay. However, developing a point-of-care plasma extraction device with a large output and high virus recovery remains a significant obstacle to the success of on-site viral load tests. Here, we report a portable, easy-to-use, cost-efficient, membrane-filtration-based plasma separation device that enables rapid large-volume plasma extraction from whole blood, designed for point-of-care virus assays. The plasma separation is realized by a low-fouling zwitterionic polyurethane-modified cellulose acetate (PCBU-CA) membrane. The zwitterionic coating on the cellulose acetate membrane can decrease surface protein adsorption by 60% and increase plasma permeation by 46% compared with a pristine membrane. The PCBU-CA membrane, with its ultralow-fouling properties, enables rapid plasma separation. The device can yield a total of 1.33 mL plasma from 10 mL whole blood in 10 min. The extracted plasma is cell-free and exhibits a low hemoglobin level. In addition, our device demonstrated a 57.8% T7 phage recovery in the separated plasma. The results of real-time polymerase chain reaction analysis confirmed that the nucleic acid amplification curve of the plasma extracted by our device is comparable to that obtained by centrifugation. With its high plasma yield and good phage recovery, our plasma separation device provides an excellent replacement for traditional plasma separation protocols for point-of-care virus assays and a broad spectrum of clinical tests.
Molecular dynamics and continuum analyses of the electrokinetic zeta potential in nanostructured slit channels
This work presents a theoretical and numerical study of electrokinetic flow and the zeta potential for the case of slit channels with nanoscale surface features of dimensions comparable to the Debye length, by employing molecular dynamics simulations and continuum-level analyses. Additionally, a simple analytical model for considering the average effect of such surface features producing nanoscale roughness is proposed by employing matched asymptotic solutions for the charge density and fluid flow field, and matching conditions that satisfy electroneutrality and the Onsager reciprocal relation between the electroosmotic flow rate and streaming current. The proposed analytical model quantitatively accounts for results from molecular dynamics simulations that consider the presence of ion solvation shells and surface hydration layers. Our analysis indicates that a simultaneous knowledge of the electroosmotic and pressure-driven flow rate or streaming current can be instrumental to unambiguously determine the zeta potential in the presence of nanoscale surface features.