Search NASA⌕ Search

Engineering topics

Hull, D. G.

Publications and source records attributed to Hull, D. G..

18 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Maximum orbit plane change with heat-transfer-rate considerations

Two aerodynamic maneuvers are considered for maximizing the plane change of a circular orbit: gliding flight with a maximum thrust segment to regain lost energy (aeroglide) and constant altitude cruise with the thrust being used to cancel the drag and maintain a high energy level (aerocruise). In both cases, the stagnation heating rate is limited. For aeroglide, the controls are the angle of attack, the bank angle, the time at which the burn begins, and the length of the burn. For aerocruise, the maneuver is divided into three segments: descent, cruise, and ascent. During descent the thrust is zero, and the controls are the angle of attack and the bank angle. During cruise, the only control is the assumed-constant angle of attack. During ascent, a maximum thrust segment is used to restore lost energy, and the controls are the angle of attack and bank angle. The optimization problems are solved with a nonlinear programming code known as GRG2. Numerical results for the Maneuverable Re-entry Research Vehicle with a heating-rate limit of 100 Btu/ft(2)-s show that aerocruise gives a maximum plane change of 2 deg, which is only 1 deg larger than that of aeroglide. On the other hand, even though aerocruise requires two thrust levels, the cruise characteristics of constant altitude, velocity, thrust, and angle of attack are easy to control.

Lee, J. Y.↗
NASA NTRS1986

Aero-assisted orbital plane change using an elliptic drag polar

A three-impulse, aero-assisted maneuver is used to change the plane of a circular orbit. The guidance law used during the atmospheric phase is based on the repetitive use of an approximate optimal control law. The approximations include Loh's term being constant, an exponential atmosphere, and a constant-coefficient drag polar. Whereas the true optimal trajectory is flown at maximum lift-to-drag ratio, simulation results for a parabolic drag polar show the angle of attack becoming large near the end of the trajectory. Here, the approximate optimal control rule is developed for an elliptic polar which has maximum lift coefficient and higher values of the drag coefficient at high values of the lift coefficient than the parabolic polar. Simulation results show that the angle of attack still increases to high values near the end of the trajectory and that, overall, the parabolic drag polar produces better results. Finally, it is shown that Loh's term is not constant over the ascent portion of the atmospheric turn and is the probable cause of high angles of attack. However, the guidance laws developed by assuming Loh's term to be constant work well.

Hull, D. G.↗
NASA NTRS1985

New analytical results for AOTV guidance

Minimum energy-loss turns of an Aero-assisted, Orbital Transfer Vehicle (AOTV) performing the atmospheric portion of an orbital-plane-change maneuver are developed using the heading angle as the independent variable. Because the heading angle is monotonic, several difficulties previously encountered using the flight path angle, which is not monotonic, as the independent variable are eliminated. In addition, the solution of the optimal control problem reduces to the solution of a fourth-order polynomial which can be accomplished analytically.

Hull, D. G.↗
NASA NTRS1984

Minimum energy-loss guidance for aero-assisted orbital plane change

Minimum energy-loss guidance for the aero-assisted plane change of an orbiting vehicle is developed and applied to the plane change of a circular orbit. First, trajectories which minimize the fuel required to change the orbital plane are computed for a realistic vehicle. From these trajectories, it is observed that the fuel weight is minimized if the velocity at exit from the atmosphere is maximized. Next, for the atmospheric turn, approximate optimal controls (angle of attack and bank angle) which maximize the exit velocity are derived. Finally, the minimum-fuel problem is resolved using optimal guidance for the atmospheric part of the trajectory, and the optimization problem reduces to a one-dimensional parameter minimization. Successful plane changes up to 40 deg are demonstrated. Optimal guidance requires up to 14 percent more fuel than the 'true' optimum but only 50 percent of the fuel required by the single-impulse maneuver. Finally, the guidance law developed here is implementable because only algebraic manipulations are required.

Hull, D. G.↗
NASA NTRS1975

Interpolation in numerical optimization

The present work discusses the generation of the cubic-spline interpolator in numerical optimization methods which use a variable-step integrator with step size control based on local relative truncation error. An algorithm for generating the cubic spline with successive over-relaxation is presented which represents an improvement over that given by Ralston and Wilf (1967). Rewriting the code reduces the number of N-vectors from eight to one. The algorithm is formulated in such a way that the solution of the linear system set up yields the first derivatives at the nodal points. This method is as accurate as other schemes but requires the minimum amount of storage.

Hall, K. R.↗
NASA NTRS1972

Calculation of free-fall trajectories using numerical optimization methods.

An important problem in space flight is the calculation of trajectories for nonthrusting vehicles between fixed points in a given time. A new procedure based on Hamilton's principle for solving such two-point boundary-value problems is presented. It employs numerical optimization methods to perform the extremization required by Hamilton's principle. This procedure is applied to the calculation of an Earth-Moon trajectory. The results show that the initial guesses required to obtain an iteration procedure which converges are not critical and that convergence can be obtained to any predetermined degree of accuracy.

Hull, D. G.↗
NASA NTRS1971

Hypersonic bodies of maximum drag for a given lift-to-drag ratio.

The problem considered in this paper is concerned with the aerodynamic design of the forebody shape of reentry vehicles in the blunt, homothetic, elliptic transversal contour, power-law longitudinal contour, raked-off configurational set. In particular, the forebody shape which maximizes the ratio of the forebody pressure drag to the free-stream dynamic pressure for a given lift-to-drag ratio and given geometric properties is determined. This problem is considered because recent survey articles indicate that its solution will provide useful qualitative design information about manned vehicles entering the earth's atmosphere from any of the foreseeable planetary missions. Single-integral equations relating the lift and drag in Newtonian hypersonic flow to the forebody geometry are derived and used to formulate the optimization problem which is solved by a direct numerical method.

Mcmillan, W., III↗