Search NASA⌕ Search

Engineering topics

Hunt, Adrian

Publications and source records attributed to Hunt, Adrian.

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Structure Matters: Asymmetric CO Oxidation at Rh Steps with Different Atomic Packing

Curved crystals are a simple but powerful approach to bridge the gap between single crystal surfaces and nanoparticle catalysts, by allowing a rational assessment of the role of active step sites in gas-surface reactions. Using a curved Rh(111) crystal, here, we investigate the effect of A-type (square geometry) and B-type (triangular geometry) atomic packing of steps on the catalytic CO oxidation on Rh at millibar pressures. Imaging the crystal during reaction ignition with laser-induced CO 2 fluorescence demonstrates a two-step process, where B-steps ignite at lower temperature than A-steps. Such fundamental dissimilarity is explained in ambient pressure X-ray photoemission (AP-XPS) experiments, which reveal partial CO desorption and oxygen buildup only at B-steps. AP-XPS also proves that A-B step asymmetries extend to the active stage: at A-steps, low-active O–Rh–O trilayers buildup immediately after ignition, while highly active chemisorbed O is the dominant species on B-type steps. We conclude that B-steps are more efficient than A-steps for the CO oxidation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Elucidating CO Oxidation Pathways on Rh Atoms and Clusters on the “29” Cu 2 O/Cu(111) Surface

We report single-atom catalysts have attracted a great deal of attention due to their distinct reactivity and potential for cost savings. However, despite the wealth of literature in recent years, identifying the exact nature of the active sites and associated reaction mechanisms remains challenging in many cases. Herein, we take a surface science approach to understand how Rh single atoms and small clusters behave on the thin film “29” Cu 2 O grown on Cu(111). We find that in contrast to Pt, which is present solely as single atoms on the “29” Cu 2 O surface, Rh atoms and clusters coexist and each enable low-temperature CO oxidation, but via different pathways. Specifically, the single Rh atoms produce CO 2 at 444 K via a Mars van Krevelen mechanism whereas the Rh clusters can also dissociate CO, as demonstrated via isotope labeling, and liberate CO 2 at 313 K. Density functional theory (DFT) calculations quantify the energetics of these different pathways and demonstrate that only extended Rh is capable of CO dissociation. Low-temperature scanning tunneling microscopy (STM) reveals that unlike Pt atoms on the same surface, which stay atomically dispersed, the distribution of Rh structures is dependent on pretreatment conditions. DFT calculations reveal the greater tendency of Rh atoms to cluster than Pt, and STM image simulations confirm the active sites. Ambient pressure X-ray photoelectron spectroscopy studies on the same single crystal model systems demonstrate that 1% of a monolayer of Rh on the “29” Cu 2 O thin film significantly accelerates its reduction by CO at 400 K, thus confirming the ultrahigh vacuum surface science findings. Together, these results illustrate how well-defined single crystal experiments are useful in building structure–function relationships that elucidate the reactivity of different ensemble sizes with a level of detail beyond what is possible with high surface area catalysis.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Unraveling the role of tungsten as a minor alloying element in the oxidation NiCr alloys

Ni-based superalloys offer a unique combination of mechanical properties, corrosion resistance and high temperature performance. Near ambient pressure X-ray photoelectron spectroscopy was used to study in operando the initial steps of oxidation for Ni-5Cr, Ni-15Cr, Ni-30Cr and Ni-15Cr-6W at 500 °C, p(O 2 )=10 -6 mbar. The comparison of oxide evolution for these alloys quantifies the outsized impact of W in promoting chromia formation. For the binary alloys an increase in chromia due to Cr-surface enrichment is followed by NiO nucleation and growth thus seeding a dual-layer structure. The addition of W (Ni-15Cr-6W) shifts the reaction pathways towards chromia thus enhancing oxide quality. Density functional theory calculations confirm that W atoms adjacent to Cr create highly favorable oxygen adsorption sites. The addition of W supercharges the reactivity of Cr with oxygen essentially funneling oxygen atoms into Cr sites. The experimental results are discussed in the context of surface composition, chemistry, reactant fluxes, and microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Strain-Dependent Surface Defect Equilibria of Mixed Ionic-Electronic Conducting Perovskites

We report understanding the surface defect chemistry and its strain dependency is essential in developing next-generation electrochemical devices. However, due to their nanoscale dimensions, surface defects cannot be accessed by conventional techniques used in bulk defect studies. Here, we constructed the strain-dependent surface defect equilibria (i.e., the Brouwer diagram) of mixed ionic-electronic conducting perovskite oxides with near ambient pressure X-ray absorption spectroscopy. Using coherently strained thin-film La 0.6 Sr 0.4 Fe O3 (LSF) as model systems, we probed their surface defect equilibria at 400 °C in oxygen partial pressures between 1 to 10 -5 Torr. We found that the electron holes on the LSF surfaces have strong oxygen character, regardless of the strain states. Nevertheless, tensile strain makes the LSF surface more reducible than the compressed counterpart. These two observations were then validated using first-principles calculations. Finally, with the aid of thermodynamic analyses, we showed that the strain-dependent surface defect equilibria of LSF can be captured by bulk-like ideal solution defect models with shifted oxygen chemical potentials. The findings and methodology presented in this study enable quantitative determination of the surface defect chemistry, which is crucial to understanding and designing functional surfaces for efficient conversions of energy and fuels.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Additive engineering for robust interphases to stabilize high-Ni layered structures at ultra-high voltage of 4.8 V

Nickel-rich layered cathode materials promise high energy density for next-generation batteries when coupled with lithium metal anodes. However, the practical capacities accessible are far less than the theoretical values due to their structural instability during cycling, especially when charged at high voltages. Here we demonstrate that stable cycling with an ultra-high cut-off voltage of 4.8 V can be realized by using an appropriate amount of lithium difluorophosphate in a common commercial electrolyte. The Li||LiNi 0.76 Mn 0.14 Co 0.10 O 2 cell retains 97% of the initial capacity (235 mAh g -1 ) after 200 cycles. The cycling stability is ascribed to the robust interphase on the cathode. It is formed by lithium difluorophosphate decomposition, which is facilitated by the catalytic effect of transition metals. The decomposition products (Li 3 PO 4 and LiF) form a protective interphase. This suppresses transition metal dissolution and cathode surface reconstruction. It also facilitates uniform Li distribution within the cathode, effectively mitigating the strain and crack formation.

25 ENERGY STORAGE↗
DOE OSTI2022

Investigating the Elusive Nature of Atomic O from CO 2 Dissociation on Pd(111): The Role of Surface Hydrogen

CO 2 dissociation is a key step in CO 2 conversion reactions to produce value-added chemicals typically through hydrogenation. In many cases, the atomic O produced from CO 2 dissociation can potentially block adsorption sites or change the oxidation state of the catalyst. Here, we used ambient pressure X-ray photoelectron spectroscopy (AP-XPS) and density functional theory (DFT) calculations to investigate the presence of surface species from the dissociation of CO 2 on Pd(111). AP-XPS results show that CO 2 was dissociated to produce adsorbed CO, but dissociated atomic O was not observed at room temperature. We were only able to observe atomic O when CO 2 was introduced at 500 K. Further investigations of O-covered Pd(111) revealed that chemisorbed O could be easily removed by low pressures of CO and H 2 . Notably, the effect of H 2 is quite prominent since it could react with chemisorbed O at a pressure as low as 2 × 10 -9 Torr, and the presence of H2 at ambient pressure prevented CO 2 dissociation. DFT calculations showed that in the presence of background H 2 , facile CO 2 dissociation took place via the reverse water–gas shift (rWGS) reaction, which resulted in the formation of adsorbed CO and removal of O by H 2 . DFT also identified the possible variation of surface species on simultaneous exposure of CO 2 and H 2 over Pd(111) depending on temperature and pressure, which opens alternative opportunities to tune the CO 2 hydrogenation catalysis by controlling the reaction conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Avoiding CO 2 Improves Thermal Stability at the Interface of Li 7 La 3 Zr 2 O 12 Electrolyte with Layered Oxide Cathodes

Abstract Solid‐state batteries promise higher energy densities and better safety than Li‐ion batteries with liquid electrolytes. However, the interface between solid electrolyte and cathode is unstable at the elevated temperatures that are needed while sintering to achieve good bonding between ceramic components. Here, the hypothesis is that, the gas environment, especially the presence of CO 2, is critical in determining the stability of the solid electrolyte–cathode interface. The effect of gas species on the interface is systematically probed, by a using Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte with a thin film LiNi 0.6 Mn 0.2 Co 0.2 O 2 cathode as a model system to enable interface sensitivity. Detrimental phases formed at the interface and their onset conditions are identified by X‐ray absorption spectroscopy, X‐ray diffraction, and Gibbs free energy analysis. As a result, removing CO 2 and minimizing H 2 O(g) during sintering is necessary to obtain good contact at the LLZO|cathode interface without forming secondary phases. Sintering in O 2 is ideal, yielding excellent chemical stability and low interfacial resistance. Secondary phases also do not form in N 2, but oxygen loss occurs at elevated temperatures. The interfacial resistance obtained upon sintering in pure O 2 is comparable to the lowest values at LLZO interfaces with protective coatings, but here without the need for interface coatings.

25 ENERGY STORAGE↗
DOE OSTI2022

Water Formation Reaction under Interfacial Confinement: Al0.25Si0.75O2 on O-Ru(0001)

Confined nanosized spaces at the interface between a metal and a seemingly inert material, such as a silicate, have recently been shown to influence the chemistry at the metal surface. In prior work, we observed that a bilayer (BL) silica on Ru(0001) can change the reaction pathway of the water formation reaction (WFR) near room temperature when compared to the bare metal. In this work, we looked at the effect of doping the silicate with Al, resulting in a stoichiometry of Al0.25Si0.75O2. We investigated the kinetics of WFR at elevated H2 pressures and various temperatures under interfacial confinement using ambient pressure X-ray photoelectron spectroscopy. The apparent activation energy was lower than that on bare Ru(0001) but higher than that on the BL-silica/Ru(0001). The apparent reaction order with respect to H2 was also determined. The increased residence time of water at the surface, resulting from the presence of the BL-aluminosilicate (and its subsequent electrostatic stabilization), favors the so-called disproportionation reaction pathway (*H2O + *O ↔ 2 *OH), but with a higher energy barrier than for pure BL-silica.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Exsolution Synthesis of Nanocomposite Perovskites with Tunable Electrical and Magnetic Properties

Nanostructured functional oxides play an important role in enabling clean energy technologies and novel memory and processor devices. Using thin-film La 0.6 Sr 0.4 FeO 3 (LSF) as a model system, the novel utility of exsolution in fabricating self-assembled metal oxide nanocomposites with tunable functionalities is shown. Exsolution triggers the formation of metallic iron (Fe 0 ) nanoparticles, Ruddlesden–Popper domains, and nm-scale percolated Fe-deficient channels in LSF. Combining multimodal characterization with numerical modeling, the chemical, magnetic, and electrical properties of the exsolution-synthesized nanocomposite at different stages of Fe 0 exsolution as well as during redox cycling are assessed. After exsolution, the electronic conductivity of the nanocomposite LSF increased by more than two orders of magnitude. Based on numerical analysis representing all the constituents, it is expected that this increase in conductivity originates mainly from the Fe-deficient percolating channels formed during exsolution. Moreover, the exsolved nanocomposite is redox-active even at moderate temperatures. Such redox capabilities can enable dynamic control of the nanocomposite functionality by tailoring the oxygen non-stoichiometry. This concept is demonstrated with a continuous modulation of magnetization between 0 and 110 emu cm -3 . These findings point out that exsolution may serve as a platform for scalable fabrication of complex metal oxide nanocomposites for electrochemical and electronic applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stabilizing electrode–electrolyte interfaces to realize high-voltage Li||LiCoO 2 batteries by a sulfonamide-based electrolyte

High-voltage lithium-metal batteries (LMBs) with LiCoO 2 (LCO) as the cathode have high volumetric and gravimetric energy densities. However, it remains a challenge for stable cycling of LCO >4.5 V Li . Here we demonstrate that a rationally designed sulfonamide-based electrolyte can greatly improve the cycling stability at high voltages up to 4.7 V Li by stabilizing the electrode–electrolyte interfaces (EEIs) on both the Li-metal anode (LMA) and high-voltage LCO cathode. With the sulfonamide-based electrolyte, commercial LCO cathodes retain 89% and 85% of their capacities after 200 and 100 cycles under high charging voltages of 4.55 V Li and 4.6 V Li , respectively, significantly outperforming traditional carbonate-based electrolytes. The surface degradation, impedance growth, and detrimental side reactions in terms of gas evolution and Co dissolution are well suppressed. Our work demonstrates a promising strategy for designing new electrolytes to realize high-energy Li||LCO batteries.

25 ENERGY STORAGE↗
DOE OSTI2021

Xenon Trapping in Metal-Supported Silica Nanocages

Xenon (Xe) is a valuable and scarce noble gas used in various applications, including lighting, electronics, and anesthetics, among many others. It is also a volatile byproduct of the nuclear fission of uranium. In this work, a novel material architecture consisting of silicate nanocages in contact with a metal surface and an approach for trapping single Xe atoms in these cages is presented. The trapping is done at low Xe pressures and temperatures between 400 and 600 K, and the process is monitored in situ using synchrotron-based ambient pressure X-ray photoelectron spectroscopy. Release of the Xe from the cages occurs only when heating to temperatures above 750 K. A model that explains the experimental trapping kinetics is proposed and tested using Monte Carlo methods. Density functional theory calculations show activation energies for Xe exiting the cages consistent with experiments. This work can have significant implications in various fields, including Xe production, nuclear power, nuclear waste remediation, and nonproliferation of nuclear weapons. The results are also expected to apply to argon, krypton, and radon, opening an even more comprehensive range of applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Microscopic relaxation channels in materials for superconducting qubits

Despite mounting evidence that materials imperfections are a major obstacle to practical applications of superconducting qubits, connections between microscopic material properties and qubit coherence are poorly understood. Here, we combine measurements of transmon qubit relaxation times ( T 1 ) with spectroscopy and microscopy of the polycrystalline niobium films used in qubit fabrication. By comparing films deposited using three different techniques, we reveal correlations between T 1 and intrinsic film properties such as grain size, enhanced oxygen diffusion along grain boundaries, and the concentration of suboxides near the surface. Qubit and resonator measurements show signatures of two-level system defects, which we propose to be hosted in the grain boundaries and surface oxides. We also show that the residual resistance ratio of the polycrystalline niobium films can be used as a figure of merit for qubit lifetime. This comprehensive approach to understanding qubit decoherence charts a pathway for materials-driven improvements of superconducting qubit performance.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Tuning Point Defects by Elastic Strain Modulates Nanoparticle Exsolution on Perovskite Oxides

Exsolution generates stable and catalytically active metal nanoparticles via phase precipitation out of a host oxide. An ability to control the size and dispersion of the exsolution particles is desirable for design of nanostructured (electro)catalysts. In this work, we demonstrate that tuning point defects by lattice strain affects both the thermodynamics and the kinetics of iron (Fe 0 ) exsolution on La 0.6 Sr 0.4 FeO 3 (LSF) thin film model. By combining in situ surface characterization and ab initio defect modeling, we show oxygen vacancy and Schottky defects to be the primary point defects formed upon Fe0 exsolution. Lattice strain tunes the formation energy, and thus the abundance of these defects, and alters the amount and size of the resulting exsolution particles. In addition, we find that the density of exsolved nanoparticles matches the concentration of oxygen vacancy pairs, thus pointing to the surface oxygen vacancy pairs as preferential nucleation sites for exsolution. The tensile-strained LSF with a facile formation of these critical point defects results in a higher Fe 0 metal concentration, a larger density of nanoparticles, and a reduced particle size at its surfaces. These results provide important mechanistic insights and highlight the role of point-defect engineering in designing nanostructured catalysts in energy and fuel conversion technologies.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Modification of the Coordination Environment of Active Sites on MoC for High-Efficiency CH 4 Production

Modulating the coordination environment of active sites on catalyst surfaces is crucial to developing effective catalysts and controlling catalysis, but it is highly challenging. Guided by our first-principles calculations, we experimentally accomplish the modification of the coordination environment of active sites on MoC nanoparticle surfaces by anchoring pyridinic N atom rings of holey graphene on Mo atoms. The rings produce electrostatic forces that enable the tuning of the Mo sites' affinity to reaction intermediates, which passivates Mo hollow sites, activates Mo top sites and reduces the over-adsorption of OH on the Mo active sites, as predicted by the calculations. The atomic-level modification is well confirmed by atomic-resolution imaging, high-resolution electron tomography, synchrotron soft X-ray spectroscopy and operando electrochemical infrared spectroscopy. Consequently, the Faradaic efficiency for CO 2 reduction to CH 4 is enhanced from 16% to 89%, a record high efficiency so far, in aqueous electrolyte. Meantime, it also exhibits a negligible activity loss over 50 h.

77 NANOSCIENCE AND NANOTECHNOLOGY↗